BS EN ISO 15480-1999 Hexagon washer head drilling screws with tapping screw thread《带攻丝螺纹的六角头垫圈自攻螺钉》.pdf

1、BRITISH STANDARD BS EN ISO 15480:1999 Hexagon washer head drilling screws with tapping screw thread The European Standard EN ISO15480:1999has the status of a British Standard ICS 21.060.10BSENISO15480:1999 This British Standard, having been prepared under the directionof the Engineering SectorCommit

2、tee, was publishedunder the authority of the Standards Committee and comes into effect on 15November1999 BSI 04-2000 ISBN 0 580 35002 9 National foreword This British Standard is the English language version of ENISO15480:1999. It is identical with ISO15480:1999. The UK participation in its preparat

3、ion was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/2, Slotted and recessed head screws, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretati

4、on, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fac

5、t that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue und

6、er the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct a

7、pplication. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISOtitle page, page 2, the ISO title page, pages ii to iv, pages 1 to 4, aninside back cover

8、and aback cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSENISO15480:1999 BSI 04-2000 i Contents Page National for

9、eword Inside front cover Foreword 2 Foreword iii Text of ISO 15480 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15480 September 1999 ICS 21.060.00 English version Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999) Vis autoperceuses tte hexagonale amba

10、se plate, avec filetage de vis tle (ISO15480:1999) Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde (ISO15480:1999) This European Standard was approved by CEN on16July1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

11、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions

12、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech

13、Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de

14、Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO15480:1999EENISO15480:1999 2 BSI 04-2000 Foreword The text of the International Standard ISO15480:1999has been prepared by Technical Committee ISO

15、/TC2 “Fasteners” in collaboration with Technical Committee CEN/TC185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

16、endorsement, at the latest by March2000, and conflicting national standards shall be withdrawn at the latest by March2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgiu

17、m, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom. Endorsement notice The text of the International Standard ISO15480:1999 was approved by CEN as a European Standard withou

18、t any modification. NOTENormative references to International Standards are listed in Annex ZA (normative).ENISO15480:1999 ii BSI 04-2000 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 Dimensions 1 4 Specifications and reference International Standards 3 5 Designation 3 Annex ZA (no

19、rmative) Normative references to international publications with their relevant European publications Inside back cover Bibliography 4 Figure 1 1 Table 1 Dimensions 2 Table 2 Specifications and reference International Standards 3ENISO15480:1999 BSI 04-2000 iii Foreword ISO (the International Organiz

20、ation for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

21、 has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. I

22、nternational Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the m

23、ember bodies casting a vote. International Standard ISO15480was prepared by Technical Committee ISO/TC2, Fasteners.iv blankENISO15480:1999 BSI 04-2000 1 1 Scope This International Standard specifies the characteristics of hexagon washer head drilling screws with tapping screw threads from ST2,9up to

24、 and including ST6,3. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. Howe

25、ver, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and

26、IEC maintain registers of currently valid International Standards. ISO 1478:1999, Tapping screw thread. ISO 3269:, Fasteners Acceptance inspection 1) . ISO 4042:1999, Fasteners Electroplated coatings. ISO 4759-1:, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and

27、C 2) . ISO 10666:1999, Drilling screws with tapping screw thread Mechanical and functional properties. 3 Dimensions See Figure 1 and Table 1. 1) To be published. (Revision of ISO 3269:1988) 2) To be published. (Revision of ISO4759-1:1978) a The function of the drilling point (diameter d p ) is speci

28、fied in ISO10666. Figure 1 ENISO15480:1999 2 BSI 04-2000 Table 1 Dimensions Dimensions in millimetres Thread ST2,9 ST3,5 ST4,2 ST4,8 ST5,5 ST6,3 p a 1,1 1,3 1,4 1,6 1,8 1,8 a b max. 1,1 1,3 1,4 1,6 1,8 1,8 d c max. 6,3 8,3 8,8 10,5 11 13,5 min. 5,8 7,6 8,1 9,8 10 12,2 c min. 0,4 0,6 0,8 0,9 1 1 s no

29、m. = max. 4,00 c 5,50 7,00 8,00 8,00 10,00 min. 3,82 5,32 6,78 7,78 7,78 9,78 e min. 4,28 5,96 7,59 8,71 8,71 10,95 k nom. = max. 2,8 3,4 4,1 4,3 5,4 5,9 min. 2,5 3,0 3,6 3,8 4,8 5,3 k w d min. 1,3 1,5 1,8 2,2 2,7 3,1 r 1 max. 0,4 0,5 0,6 0,7 0,8 0,9 r 2 max. 0,2 0,25 0,3 0,3 0,4 0,5 Drilling range

30、sheet or plate thickness) e from 0,7 0,7 1,75 1,75 1,75 2 to 1,9 2,25 3 4,4 5,25 6 l l g f nom. min. max. min. 9,5 8,75 10,25 3,25 2,85 13 12,1 13,9 6,6 6,2 4,3 3,7 16 15,1 16,9 9,6 9,2 7,3 5,8 5 19 18 20 12,5 12,1 10,3 8,7 8 7 22 21 23 15,1 13,3 11,7 11 10 25 24 26 18,1 16,3 14,7 14 13 32 30,75 33

31、25 23 21,5 21 20 38 36,75 39,25 29 27,5 27 26 45 43,75 46,25 34,5 34 33 50 48,75 51,25 39,5 39 38 a P is the pitch of the thread. b a is the distance from the underside of the head to the first major diameter of the thread. c Divergence from the width across flats for hexagon tapping screws in acco

32、rdance with ISO1479 (5mm). In the case of hexagon washer head tapping screws (see ISO7053) the width across flats of4mm has been introduced world-wide and also applies in this case. d k wis the wrenching height. e In order to determine the nominal length l it may be necessary to add an air gap (if p

33、resent) to the individual sheet or plate thickness. f l gis the distance from the underside of the head to the last major diameter of the thread.ENISO15480:1999 BSI 04-2000 3 4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standa

34、rds 5 Designation EXAMPLE A hexagon washer head drilling screw with thread ST3,5and nominal length l=16mm is designated as follows: Drilling screw ISO 15480 ST3,5 16 Material Steel International Standard ISO 10666 Thread International Standard ISO 1478 Mechanical and functional properties Internatio

35、nal Standard ISO 10666 Tolerances Product grade A International Standard ISO 4759-1 Finish Plain Requirements for electroplating are covered in ISO 4042. Acceptability Acceptance procedure is covered in ISO 3269.ENISO15480:1999 4 BSI 04-2000 Bibliography 1 ISO 1479:1983, Hexagon head tapping screws.

36、 2 ISO 7053:1992, Hexagon washer head tapping screws.ENISO15480:1999 BSI 04-2000 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. Th

37、ese normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For unda

38、ted references the latest edition of the publication referred to applies. Publication Year Title EN Year ISO 1478 1999 Tapping screws thread EN ISO 1478 1999 ISO 1479 1983 Hexagon head tapping screws EN ISO 1479 1994 ISO 4042 1999 Fasteners Electroplated coatings EN ISO 4042 1999BS EN ISO 15480:1999

39、 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are

40、 updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Bri

41、tishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lates

42、t editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those tha

43、t have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are

44、also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these

45、and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

46、 Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of nece

47、ssary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.