BS EN ISO 15874-1-2013 Plastics piping systems for hot and cold water installations Polypropylene (PP) General《热水和冷水设施用塑料管道系统 聚丙烯(PP) 总则》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlastics piping systems for hot and cold water installations Polypropylene (PP)Part 1: GeneralBS EN ISO 15874-1:2013National forewordThis British Standard is the UK implementatio

2、n of EN ISO 15874-1:2013. Itsupersedes BS EN ISO 15874-1:2003 which is withdrawn.The UK participation in its preparation was entrusted by Technical CommitteePRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastics piping forpressure applications.A list of organizations represented on this

3、 committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2013Published by BSI Standards Limited 2013ISBN 978 0 580 71667 6ICS 23.0

4、40.01; 91.140.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 March 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN I

5、SO 15874-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15874-1 February 2013 ICS 23.040.20; 91.140.60 Supersedes EN ISO 15874-1:2003English Version Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013) Systmes de canal

6、isations en plastique pour les installations deau chaude et froide - Polypropylne (PP) - Partie 1: Gnralits (ISO 15874-1:2013) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polypropylen (PP) - Teil 1: Allgemeines (ISO 15874-1:2013) This European Standard was approved by CE

7、N on 5 January 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

8、 may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifi

9、ed to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icel

10、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre

11、: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15874-1:2013: EBS EN ISO 15874-1:2013EN ISO 15874-1:2013 (E) 2 Contents Page Foreword 3 BS EN ISO 15874-1:2013EN ISO 15874-1:2013 (E) 3 Fo

12、reword This document (EN ISO 15874-1:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”

13、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at the latest by August 2013. Attention is drawn to the possibility that some o

14、f the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15874-1:2003. According to the CEN-CENELEC Internal Regulations, the national standards organizations o

15、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

16、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN ISO 15874-1:2013ISO 15874-1:2013(E) ISO 2013 All rights reserved iiiContents PageIntroduction v1 Scope 12 Normative references . 13 Terms and definitions, symbols and abb

17、reviated terms 13.1 Terms and definitions . 23.2 Symbols . 53.3 Abbreviated terms . 64 Classification of service conditions . 65 Material . 75.1 General . 75.2 Influence on water intended for human consumption 85.3 Reprocessable material . 86 System performance requirement 8Bibliography . 9BS EN ISO

18、 15874-1:2013ISO 15874-1:2013(E)IntroductionThis part of ISO 15874 specifies the requirements for a piping system and its components when made from polypropylene (PP). The piping system is intended to be used for hot and cold water installations.Regarding potential undesirable effects on the quality

19、 of water intended for human consumption, caused by the product covered by ISO 15874 no information is provided as to whether the product can be used without restriction, and existing national regulations concerning the use and/or the characteristics of this product remain in force.Requirements and

20、test methods for components of the piping system are specified in ISO 15874-2 and ISO 15874-3. Characteristics for fitness of purpose (mainly for joints) are covered in ISO 15874-5. ISO/TS 15874-7 gives guidance for the assessment of conformity.This part of ISO 15874 specifies the general aspects of

21、 the plastics piping system.At the date of publication of this part of ISO 15874, the following system International Standards for piping systems of other plastics materials used for the same application areISO 15875, Plastics piping systems for hot and cold water installations Crosslinked polyethyl

22、ene (PE-X)ISO 15876, Plastics piping systems for hot and cold water installations Polybutylene (PB)ISO 15877, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C)ISO 22391, Plastics piping systems for hot and cold water installations - Polyethylene of

23、 raised temperature resistance (PE-RT)The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent.ISO takes no position concerning the evidence, validity and scope of this patent right.The

24、holder of this patent right has assured ISO that they are willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Information may be obta

25、ined from:Borealis AGWagramerstrasse 17-19, A-1220, Vienna, AustriaAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights.I

26、SO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line databases of patents relevant to their standards. Users are encouraged to consult the databases for the most up to date information concerning patents. ISO 2013 All rights reserved vBS EN ISO 15874-1:2013Plastics piping systems

27、 for hot and cold water installations Polypropylene (PP) Part 1: General1 ScopeThis part of ISO 15874 specifies the general aspects of polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for h

28、uman consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application (see Table 1).It covers a range of service conditions (classes of application), design pressures and pipe dimension classes. Values of TD, Tmaxand Tmalin excess

29、 of those in Table 1 of this part of ISO 15874 do not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.I

30、t also specifies the test parameters for the test methods referred to in this part of ISO 15874.In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to PP pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intend

31、ed to be used for hot and cold water installations.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest editi

32、on of the referenced document (including any amendments) applies.ISO 15874-2:2013, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 2: PipesISO 15874-3, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 3: FittingsISO 472, Plasti

33、cs VocabularyISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 4065, Thermoplastics pipes Universal wall thickness table3 Terms and definitions, symbols and abbreviated termsFor the purposes of this document, the terms and definitions give

34、n in ISO 472, ISO 1043-1 and the following apply.INTERNATIONAL STANDARD ISO 15874-1:2013(E) ISO 2013 All rights reserved 1BS EN ISO 15874-1:2013ISO 15874-1:2013(E)3.1 Terms and definitions3.1.1 Geometrical terms and definitions3.1.1.1nominal sizeDNnumerical designation of the size of a component, wh

35、ich is a convenient round number, approximately equal to the manufacturing dimensions in millimetres (mm)3.1.1.2nominal sizeDN/ODnominal size, related to outside diameter3.1.1.3nominal outside diameterdnspecified diameter, in millimetres, assigned to a nominal size DN/OD3.1.1.4outside diameter (at a

36、ny point)demeasured outside diameter through the cross-section at any point of a pipe or spigot end of a fitting, rounded up to the nearest 0,1 mm3.1.1.5mean outside diameterdemmeasured length of the outer circumference of a pipe or spigot end of a fitting in any cross section divided by ( 3,142) ro

37、unded up to the nearest 0,1 mm3.1.1.6minimum mean outside diameterdem,minminimum value of the mean outside diameter as specified for a given nominal size3.1.1.7maximum mean outside diameterdem,maxmaximum value of the mean outside diameter as specified for a given nominal size3.1.1.8mean inside diame

38、ter of socketdsmarithmetical mean of two measured inside diameters perpendicular to each other at the midpoint of the socket length3.1.1.9out-of-roundnessovalitydifference between the measured maximum outside diameter and the measured minimum outside diameter in the same cross-sectional plane of a p

39、ipe or spigot end of a fitting, or the difference between the measured maximum inside diameter and the measured minimum inside diameter in the same cross-sectional plane of a socket3.1.1.10nominal wall thicknessennumerical designation of the wall thickness of a component, approximately equal to the

40、manufacturing dimension in millimetres (mm)2 ISO 2013 All rights reservedBS EN ISO 15874-1:2013ISO 15874-1:2013(E)3.1.1.11wall thickness (at any point)emeasured wall thickness at any point around the circumference of a component, rounded up to the nearest 0,1 mm3.1.1.12minimum wall thickness (at any

41、 point)eminminimum wall thickness at any point around the circumference of a component, as specified3.1.1.13maximum wall thickness at any pointemaxmaximum wall thickness at any point around the circumference of a component, as specified3.1.1.14tolerancepermitted variation of the specified value of a

42、 quantity, expressed as the difference between the permitted maximum and the permitted minimum value3.1.1.15pipe seriesSdimensionless number for pipe designation conforming to ISO 4065Note 1 to entry: According to ISO 15874 the pipe series S is used as a means for selecting pipe sizes for practical

43、purposes (see ISO 15874-2).3.1.1.16calculated pipe valueScalcvalue for a specific pipe calculated according to the following equation, rounded up to the nearest 0,1 mm:Sdeecalcnnn= - 2where:dn is the nominal outside diameter, in millimetres;en is the nominal wall thickness, expressed in millimetres3

44、.1.2 Terms and definitions related to service conditions3.1.2.1design pressurepDhighest pressure related to the circumstances for which the system has been designed and is intended to be usedNote 1 to entry: The design pressure (pD) is equal to the maximum design pressure (MDP), as specified in EN 8

45、06-1 3. ISO 2013 All rights reserved 3BS EN ISO 15874-1:2013ISO 15874-1:2013(E)3.1.2.2hydrostatic stressstress, expressed in megapascals, induced in the wall of a pipe when a pressure is applied using water as a medium. It is calculated using the following approximate equation: = - )2em minminpdee(w

46、here:p is the applied pressure, in megapascals;dem is the mean outside diameter of the pipe, in millimetres;eminis the minimum wall thickness, in millimetres.3.1.2.3design temperatureTDa temperature or a combination of temperatures of the conveyed water dependent on the service conditions for which

47、the system has been designed3.1.2.4maximum design temperatureTmaxhighest design temperature, TD, occurring for short periods only3.1.2.5malfunction temperatureTmalhighest temperature that can be reached when the control limits are exceeded3.1.2.6cold water temperatureTcoldtemperature of conveyed col

48、d water of up to approximately 25 CNote 1 to entry: For design purposes 20 C is used.3.1.2.7treated water for heating installationswater, intended for heating installations, which contains additives which have no detrimental effect on the system3.1.3 Terms and definitions related to material charact

49、eristics3.1.3.1lower confidence limit of the predicted hydrostatic strengthLPLquantity, in megapascals (MPa), with the dimensions of stress, which represents the 97,5 % lower confidence limit of the predicted hydrostatic strength at the given temperature, T, and time, t3.1.3.2design stressDallowable stress, in megapascals (MPa), in the pipe material, DP, or in the plastics fitting material, DF, for a given application or set of service conditions, respectivelyNote 1 to entry: See also Annex A of I