1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlastics piping systems for hot and cold water installations Polypropylene (PP)Part 3: FittingsBS EN ISO 15874-3:2013National forewordThis British Standard is the UK implementati
2、on of EN ISO 15874-3:2013. Itsupersedes BS EN ISO 15874-3:2003 which is withdrawn.The UK participation in its preparation was entrusted by Technical CommitteePRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastics piping forpressure applications.A list of organizations represented on thi
3、s committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2013Published by BSI Standards Limited 2013ISBN 978 0 580 71669 0ICS 23.
4、040.01; 91.140.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 March 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN
5、ISO 15874-3:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15874-3 February 2013 ICS 23.040.45; 91.140.60 Supersedes EN ISO 15874-3:2003English Version Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013) Systmes de can
6、alisations en plastique pour les installations deau chaude et froide - Polypropylne (PP) - Partie 3: Raccords (ISO 15874-3:2013) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polypropylen (PP) - Teil 3: Formstcke (ISO 15874-3:2013) This European Standard was approved by CE
7、N on 5 January 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards
8、 may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifi
9、ed to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icel
10、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre
11、: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15874-3:2013: EBS EN ISO 15874-3:2013EN ISO 15874-3:2013 (E) 2 Contents Page Foreword 3 BS EN ISO 15874-3:2013EN ISO 15874-3:2013 (E) 3 Fo
12、reword This document (EN ISO 15874-1:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”
13、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at the latest by August 2013. Attention is drawn to the possibility that some o
14、f the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15874-3:2003. According to the CEN-CENELEC Internal Regulations, the national standards organizations o
15、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net
16、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN ISO 15874-3:2013ISO 15874-3:2013(E) ISO 2013 All rights reserved iiiContents PageIntroduction v1 Scope 12 Normative references . 13 Terms and definitions, symbols and abb
17、reviated terms 23.2 Mechanical fittings 23.3 Fittings for fusion 34 Material characteristics 34.1 Plastics fitting material 34.2 Metallic fitting material . 54.3 Influence on water intended for human consumption 55 General characteristics 55.1 Appearance 55.2 Opacity . 56 Geometrical characteristics
18、 . 66.1 General 66.2 Dimensions of sockets for socket fusion and electrofusion fittings 66.3 Dimensions of metallic fittings 97 Mechanical characteristics of plastics fittings 107.1 General .107.2 Fitting material identical to the PP pipe compound 107.3 Fitting made from PP not identical to the PP p
19、ipe compound 107.4 Fittings made from plastics other than PP .108 Physical and chemical characteristics of plastics components 129 Sealing elements .1310 Performance requirements .1311 Marking .1311.1 General requirements .1311.2 Minimum required marking .1311.3 Additional marking .14Bibliography .1
20、5BS EN ISO 15874-3:2013ISO 15874-3:2013(E)IntroductionThis part of ISO 15874 specifies the requirements for a piping system and its components when made from polypropylene (PP). The piping system is intended to be used for hot and cold water installations.Regarding potential undesirable effects on t
21、he quality of water intended for human consumption, caused by the product covered by ISO 15874 no information is provided as to whether the product can be used without restriction, and existing national regulations concerning the use and/or the characteristics of this product remain in force.Require
22、ments and test methods for materials and components, other than fittings, are specified in ISO 15874-1 and ISO 15874-2. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15874-5. ISO/TS 15874-7 gives guidance for the assessment of conformity.This part of ISO 15874 specif
23、ies the characteristics of the fittings.At the date of publication of this part of ISO 15874, the following system International Standards for piping systems of other plastics materials used for the same application are ISO 15875, Plastics piping systems for hot and cold water installations Crosslin
24、ked polyethylene (PE-X) ISO 15876, Plastics piping systems for hot and cold water installations Polybutylene (PB) ISO 15877, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) ISO 22391, Plastics piping systems for hot and cold water installations P
25、olyethylene of raised temperature resistance (PE-RT)The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent.ISO takes no position concerning the evidence, validity and scope of this pat
26、ent right.The holder of this patent right has assured ISO that they are willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Informati
27、on may be obtained from:Borealis AGWagramerstrasse 17-19, A-1220,Vienna, AustriaAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such pa
28、tent rights.ISO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line databases of patents relevant to their standards. Users are encouraged to consult the databases for the most up to date information concerning patents. ISO 2013 All rights reserved vBS EN ISO 15874-3:2013Plastics p
29、iping systems for hot and cold water installations Polypropylene (PP) Part 3: Fittings1 ScopeThis part of ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, w
30、hether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see ISO 15874-1:2013, Table 1).It covers a range of service conditions (application classes) and design pressure classes. For values
31、of TD, Tmaxand Tmalin excess of those in Table 1 of ISO 15874-1:2013 do not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installatio
32、n practices or codes.It also specifies the parameters for the test methods referred to in this part of ISO 15874.In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to fittings made from PP and to fittings made from other materials which are intended to be fitted t
33、o pipes conforming to ISO 15874-2 for hot and cold water installations, whereby the joints conform to the requirements of ISO 15874-5.This part of ISO 15874 is applicable to fittings of the following types: socket fusion fittings; electro fusion fittings; mechanical fittings; fittings with incorpora
34、ted inserts.It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to ISO 15874-2, conform to the requirements of ISO 15874-5.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indis
35、pensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances
36、and designation ISO 3126, Plastics piping systems Plastics components Determination of dimensionsISO 1133-1, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics.ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fl
37、uids Determination of the resistance to internal pressure Part 1: General method INTERNATIONAL STANDARD ISO 15874-3:2013(E) ISO 2013 All rights reserved 1BS EN ISO 15874-3:2013ISO 15874-3:2013(E)ISO 1167-3 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of th
38、e resistance to internal pressure Part 3: Preparation of componentsISO 1167-4 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies ISO 7686, Plastics pipes and fittings Determination of opaci
39、tyISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolationISO 15874-1:2013, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 1: General ISO 15874-2:2013, Plastics pi
40、ping system for hot and cold water installations Polypropylene (PP) Part 2: Pipes ISO 15874-5, Plastics piping system for hot and cold water installations Polypropylene (PP) Part 5: Fitness for purpose of the system EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in wate
41、r and drainage applications Part 1: Vulcanized rubber.EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers.EN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use
42、with plastics pipes.EN 10088-1, Stainless steels Part 1: List of stainless steels.EN 10226-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Taper external threads and parallel internal treads Dimensions, tolerances and designation.3 Terms and definitions, symbols and abbre
43、viated termsFor the purposes of this document, the terms and definitions, symbols and abbreviations given in ISO 15874-1 and the following apply3.1fittingcomponent of a piping system, which connects two or more pipes and/or fittings together, without any further function3.2 Mechanical fittings3.2.1c
44、ompression fittingfitting in which the joint is made by the compression of a ring or sleeve on the outside wall of the pipe with or without additional sealing elements and with internal support3.2.2crimped fittingfitting in which the joint is made by crimping of the fitting and/or a ring on the outs
45、ide wall of the pipe by means of a special tool3.2.3flanged fittingfitting in which the pipe connection consists of two mating flanges which are mechanically pressed together and sealed by the compression of an elastomeric sealing element between them2 ISO 2013 All rights reservedBS EN ISO 15874-3:2
46、013ISO 15874-3:2013(E)3.2.4flat seat union fittingfitting in which the pipe connection consists primarily of two components, at least one of which normally incorporates a flat sealing surface, which are mechanically pressed together by means of screwed nut or similar and sealed by the compression of
47、 an elastomeric sealing element between them3.3 Fittings for fusion3.3.1socket fusion fittingfitting in which the joint with the pipe is made by melting together the outer part of the pipe with the inner part of the fitting by means of heat induced by heated tool3.3.2electro fusion fittingfitting in
48、 which the joint with the pipe is made by melting together the outer part of the pipe and the inner part of the fitting by means of heat induced by current flowing in an appropriate resistor inserted in the fitting body3.4fitting with incorporated insertsfitting in which the joint is made by means o
49、f connecting threads or other outlets, inserted in the plastics body combined with fusion ends for socket fusion or electro fusion4 Material characteristics 4.1 Plastics fitting material4.1.1 Fitting material identical to the PP pipe compoundThe PP compound shall comply with ISO 15874-1:2013, 5.1.The material shall be tested in form of tubular test pieces.When tested in accordance with the test methods specified in Table 1, using the indicated parameters, the test pi
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1