BS EN ISO 16120-3-2011 Non-alloy steel wire rod for conversion to wire Specific requirements for rimmed and rimmed substitute low-carbon steel wire rod《拔丝用非合金钢丝棒 未脱氧的和未脱氧代用的低碳钢丝棒的特.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 16120-3:2011Non-alloy steel wire rod forconversion to wirePart 3: Specific requirements for rimmedand rimmed substitute, low-carbon steelwire rod (ISO 16120-3:2011)BS E

2、N ISO 16120-3:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO16120-3:2011. It supersedes BS EN 10016-3:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/106, Wire Rod and Wire.A list of organizations

3、 represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 59722 0ICS 77.140.60; 77.140.65Compliance with a British Standard

4、 cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 16120-3 July 2011 ICS 77.1

5、40.60 Supersedes EN 10016-3:1994English Version Non-alloy steel wire rod for conversion to wire - Part 3: Specific requirements for rimmed and rimmed substitute, low-carbon steel wire rod (ISO 16120-3:2011) Fil-machine en acier non alli destin la fabrication de fils - Partie 3: Exigences spcifiques

6、au fil-machine en acier effervescent ou pseudo-effervescent bas carbone (ISO 16120-3:2011) Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 3: Besondere Anforderungen an Walzdraht aus unberuhigtem und ersatzunberuhigtem Stahl mit niedrigem Kohlenstoffgehalt (ISO 16120-3:2011) This European Standard

7、 was approved by CEN on 30 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such n

8、ational standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own la

9、nguage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

10、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Bru

11、ssels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16120-3:2011: EBS EN ISO 16120-3:2011EN ISO 16120-3:2011 (E) 3 Foreword This document (EN ISO 16120-3:2011) has been prepared by Technical Committee ISO/TC 17 “Steel“ i

12、n collaboration with Technical Committee ECISS/TC 106 “Wire rod and wires” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting

13、national standards shall be withdrawn at the latest by January 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document sup

14、ersedes EN 10016-3:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,

15、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 16120-3:2011 has been approved by CEN as a EN ISO 16120-3:2011 without any

16、 modification. BS EN ISO 16120-3:2011ISO 16120-3:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Designation 2 5 Requirements.2 5.1 General .2 5.2 Chemical composition 2 5.3 Internal soundness and surface quality3 5.4 De

17、pth of surface discontinuities3 5.5 Non-metallic inclusions 3 5.6 Tensile strength.3 5.7 Scale characteristics.4 5.8 Mechanical damage.4 Annex A (informative) Steel designations in accordance with ISO 16120-3 and designation of comparable steel grades in national or regional standards .5 Bibliograph

18、y6 BS EN ISO 16120-3:2011ISO 16120-3:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO

19、technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates clo

20、sely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Dra

21、ft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this docu

22、ment may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16120-3 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 17, Steel wire rod and wire products. This second edition cancels and replaces the first editio

23、n (ISO 16120-3:2001), which has been technically revised. ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rod for conversion to wire: Part 1: General requirements Part 2: Specific requirements for general-purpose wire rod Part 3: Specific requirements for rimm

24、ed and rimmed substitute, low-carbon steel wire rod Part 4: Specific requirements for wire rod for special applications BS EN ISO 16120-3:2011INTERNATIONAL STANDARD ISO 16120-3:2011(E) ISO 2011 All rights reserved 1Non-alloy steel wire rod for conversion to wire Part 3: Specific requirements for rim

25、med and rimmed substitute, low-carbon steel wire rod 1 Scope This part of ISO 16120 is applicable to wire rod made of low-carbon, low-silicon, rimmed and rimmed substitute steel with high ductility intended for drawing and/or cold rolling. 2 Normative references The following referenced documents ar

26、e indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 377, Steel and steel products Location and preparation of samples and test pieces

27、for mechanical testing ISO 404, Steel and steel products General technical delivery requirements ISO 4885, Ferrous products Heat treatments Vocabulary ISO 4948-1, Steels Classification Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition ISO 4948-2, Steels C

28、lassification Part 2: Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics ISO/TS 4949, Steel names based on letter symbols ISO 4967, Steel Determination of content of nonmetallic inclusions Micrographic method using standard

29、 diagrams ISO 6929, Steel products Definitions and classification ISO 16120-1:2011, Non-alloy steel wire rod for conversion to wire Part 1: General requirements BS EN ISO 16120-3:2011ISO 16120-3:2011(E) 2 ISO 2011 All rights reserved3 Terms and definitions For the purposes of this document, the term

30、s and definitions given in ISO 377, ISO 404, ISO 4885, ISO 4948-1, ISO 4948-2 and ISO 6929 and the following apply. 3.1 rimmed substitute steel continuously cast steel designed to substitute the traditional rimming steel for drawability and formability 4 Designation In the designation C#D1, C means

31、non-alloy steel for wire-drawing (see ISO/TS 4949); # is the indicative average content of carbon; D signifies that it is for wire-drawing; 1 means rimmed. 5 Requirements 5.1 General For the general requirements, see ISO 16120-1. Steels ordered according to this part of ISO 16120 are to be ordered b

32、y their chemical composition and the purchaser shall use the steel names as designated in Table 1, first column. 5.2 Chemical composition For the heat analysis, the values shown in Table 1 apply. If a product analysis is required, the permissible deviations of the product analysis in rimmed substitu

33、te steels relative to the specified value of the heat analysis are given in Table 2; these deviations are not applicable for rimmed steel. Table 1 Chemical analysis (heat analysis)aHeat analysis Steel gradebC max. % Sicmax. % Mn % P max. % S max. % Crdmax. % Nidmax. % Mo max. % Cudmax. % Alemax. % N

34、 max. % C2D1 C3D1 C4D1 0,03 0,05 0,06 0,05 0,05 0,10 0,10 - 0,35 0,20 - 0,40 0,20 - 0,45 0,020 0,025 0,025 0,020 0,025 0,025 0,10 0,10 0,15 0,10 0,10 0,15 0,03 0,03 0,03 0,10 0,15 0,15 0,01 0,05 0,05 0,007 aElements not included in this table may not be added intentionally to the steel without the a

35、greement of the purchaser, except those intended for finishing the heat. bSpecial non-alloy steel complying with ISO 4948-1 and ISO 4948-2. cA lower silicon maximum may be agreed upon between the supplier and purchaser. dThe sum of the contents Cu + Ni + Cr shall not exceed the following: for steel

36、grade C2D1, 0,25 %; for steel grade C3D1, 0,30 %; for steel grade C4D1, 0,35 %. eFor steel grades C3D1 and C4D1, a lower maximum limit may be specified at the time of ordering. BS EN ISO 16120-3:2011ISO 16120-3:2011(E) ISO 2011 All rights reserved 3Table 2 Permissible deviation in the product analys

37、is in relation to the specified value of the heat analysis Elements Steel grade Permissible deviation in product analysis % C C2D1 C3D1 to C4D1 +0,01 +0,02 Si C2D1 to C3D1 C4D1 +0,02 +0,04 Mn All grades 0,05 P and S All grades +0,005 5.3 Internal soundness and surface quality The wire rod shall have

38、 no internal and/or surface discontinuities, such as shrink holes, segregation, cracks, folds, incrustations, notches, scabs or rolling burrs, which may be detrimental to its correct use. 5.4 Depth of surface discontinuities The wire rod shall not have any surface discontinuities with depths greater

39、 than those shown in Table 3. These limit values apply for the test chosen in accordance with 9.4.3 and 9.5.3 of ISO 16120-1:2011. Table 3 applies to round wire rod only. Maximum discontinuity levels for other shapes may be agreed upon. Table 3 Limit values for the depth of surface discontinuities o

40、f round wire rod Dimensions in millimetres Nominal diameter dNMaximum permissible depth of surface discontinuities radial depthaMaximum permissible actual length of surface discontinuitiesb5 dN 12 dN 12 0,20 0,25 0,25 0,30 aThe depth of surface discontinuities measured from the actual surface of the

41、 product in a radial direction. bThe actual measured length of the discontinuity. See Annex B of ISO 16120-1:2011, for an explanation of terms. 5.5 Non-metallic inclusions The method for assessment of non-metallic inclusions and the assessment criteria shall be agreed at the time of ordering, as far

42、 as possible with reference to ISO 4967. 5.6 Tensile strength Unless otherwise specified at the time of ordering, wire rod of diameter 5,5 mm and above shall have the maximum tensile strength values shown in Table 4. BS EN ISO 16120-3:2011ISO 16120-3:2011(E) 4 ISO 2011 All rights reservedTable 4 Ten

43、sile strength values Strength in megapascals Steel grade Maximum tensile strength C2D1 C3D1 C4D1 360 390 By agreement NOTE 1 MPa = 1 N/mm2. 5.7 Scale characteristics The scale characteristics may be agreed between the supplier and purchaser. These may be specified as the quantity of scale and/or des

44、calablity. 5.8 Mechanical damage The wire rod shall have no abrasive damage (the consequence of frictional contact between wire rod and wire rod, wire rod and concrete, or wire rod and steel) detrimental to its subsequent processing and end use. Standards of acceptability relating to permissible lev

45、els of damage may be agreed between the supplier and purchaser. Illustrative examples of mechanical damage are shown in Annex C of ISO 16120-1:2011. BS EN ISO 16120-3:2011ISO 16120-3:2011(E) ISO 2011 All rights reserved 5Annex A (informative) Steel designations in accordance with ISO 16120-3 and des

46、ignation of comparable steel grades in national or regional standards This part of ISO 16120 will be adopted by CEN without changes. The equivalent European steel numbers are therefore listed in column 2 of Table A.1. Table A.1 ISO 16120-3 JIS YB/T 170.3:2002 Steel designation European material No.

47、Steel designation n/nr/yaSteel designation n/nr/yaC2D1 1.1185 C2D1 y C3D1 1.1187 C3D1 y C4D1 1.1188 C4D1 y aDeviation of the chemical analysis (heat analysis) from that given in ISO 16120-3: n = no; nr = not relevant; y = relevant. BS EN ISO 16120-3:2011ISO 16120-3:2011(E) 6 ISO 2011 All rights rese

48、rvedBibliography 1 YB/T 170.3:2002, Non-alloy steel wire rod for conversion to wire Part 3: Specific requirements for rimmed and rimmed-substitute, low-carbon steel wire rod BS EN ISO 16120-3:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body r

49、esponsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment o