BS EN ISO 17663-2009 Welding - Quality requirements for heat treatment in connection with welding and allied processes(ISO n17663 2009)《焊接 与焊接和相关工艺过程有关的热处理质量要求(ISO 17663-2009)》.pdf

1、BS EN ISO17663:2009ICS 25.160.01,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDWelding Qualityrequirements forheat treatment inconnection withwelding and alliedprocesses (ISO17663:2009)This British Standardwas published under theauthority of the StandardsPolic

2、y and StrategyCommittee on 31 July 2009 BSI 2009ISBN 978 0 580 57188 6Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 17663:2009National forewordThis British Standard is the UK implementation of EN ISO 17663:2009.It supersedes PD CR ISO 17663:2001 which is withdrawn.The UK parti

3、cipation in its preparation was entrusted to TechnicalCommittee WEE/-/1, Briefing committee for welding.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are r

4、esponsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 17663June 2009ICS 25.160.01 Supersedes CR ISO 17663:2001 English VersionWelding - Quality requirements for heat treatment in co

5、nnectionwith welding and allied processes (ISO 17663:2009)Soudage - Exigences de qualit relatives au traitementthermique associ au soudage et aux techniques connexes(ISO 17663:2009)Schweien - Qualittsanforderungen zurWrmebehandlung beim Schweien und bei verwandtenProzessen (ISO 17663:2009)This Europ

6、ean Standard was approved by CEN on 27 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni

7、ng such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own lang

8、uage and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe

9、mbourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights o

10、f exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 17663:2009: EBS EN ISO 17663:2009EN ISO 17663:2009 (E) 3 Foreword This document (EN ISO 17663:2009) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboratio

11、n with Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and conflicting national standards shall be

12、 withdrawn at the latest by December 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CR ISO 17663:2001.

13、 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

14、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 17663:2009 has been approved by CEN as a EN ISO 17663:2009 without any modification. BS EN ISO 17663:2009IS

15、O 17663:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Review of requirements and technical review. 2 4.1 General. 2 4.2 Review of requirements . 3 4.3 Technical review . 3 5 Subcontracting 4 6 Personnel. 4 7 Insp

16、ection and testing 4 7.1 General. 4 7.2 Non-destructive testing 4 7.3 Destructive testing 4 8 Equipment for heat treatment 5 8.1 Production and testing equipment . 5 8.2 Description of facilities 5 8.3 Suitability of equipment . 5 8.4 Verification of heat treatment equipment. 5 8.5 New equipment . 7

17、 8.6 Maintenance 7 9 Heat treatment activities 7 9.1 General. 7 9.2 Heat treatment parameters 7 9.3 Heat-treatment-procedure specification. 8 9.4 Work instructions . 8 9.5 Number of measuring points. 8 9.6 General rules for local post weld heat treatment of pipe work 9 10 Heat treatment record. 10 1

18、1 Non-conformance and corrective actions 10 12 Quality records 11 Annex A (informative) Example of local heat treatment. 12 Bibliography . 13 BS EN ISO 17663:2009ISO 17663:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federati

19、on of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee

20、. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance w

21、ith the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appr

22、oval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17663 was prepared by Technical Commit

23、tee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding. This first edition cancels and replaces ISO/TR 17663:2001, which has been technically revised. Requests for official interpretations of any aspect of this International Standar

24、d should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A listing of these bodies can be found at http:/www.iso.org. BS EN ISO 17663:2009INTERNATIONAL STANDARD ISO 17663:2009(E) ISO 2009 All rights reserved 1Welding Quality requirements for heat treatment in conn

25、ection with welding and allied processes 1 Scope This International Standard provides quality requirements for heat treatment in air or controlled atmospheres carried out in workshops and on site in connection with welding and forming. It applies mainly to ferritic steels, but can be used for other

26、materials, as appropriate. This International Standard provides guidance for manufacturers that perform heat treatment or produce heat-treated products or components. This International Standard can also be used as a basis for assessing the manufacturer in respect to its heat treatment capability. T

27、he fulfilment of a requirement can be waived where justification can be provided that a specific requirement is not applicable to a specific process. This International Standard is intended to be a flexible framework to provide specific requirements for heat treatment by manufacturer in order to hav

28、e a quality system in accordance with ISO 9001; specific requirements for heat treatment in specifications which require the manufacturer to have a quality system other than ISO 9001; specific guidance for a manufacturer developing a quality control system for heat treatment; specific guidance for p

29、ost weld heat treatment for manufacturers adopting ISO 3834-2 or ISO 3834-3; detailed requirements for specifications, regulations or product standards that require control of heat treatment activities. 2 Normative references The following referenced documents are indispensable for the application o

30、f this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 13916, Welding Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance tem

31、perature IEC 60584-2, Thermocouples Part 2: Tolerances EN 10052, Vocabulary of heat treatment terms for ferrous products BS EN ISO 17663:2009ISO 17663:2009(E) 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 13916 and EN

32、10052 and the following apply. 3.1 manufacturer person or organization responsible for heat treatment of products or components 3.2 loading temperature temperature of the furnace at the stage when the product or component is put into the furnace 3.3 holding temperature temperature at which the produ

33、ct or component is kept in order to achieve the specified properties NOTE 1 The holding temperature depends on the type of heat treatment, type of material and material thickness. NOTE 2 Normally, the holding temperature is expressed as a temperature range. 3.4 holding time time the product or compo

34、nent is kept at the holding temperature NOTE 1 The holding time starts when the temperature at all measuring points has reached the minimum value of the range of the holding temperature and stops when one of the measuring points falls below that temperature. NOTE 2 The holding time depends on the ty

35、pe of heat treatment, material and material thickness. 3.5 unloading temperature temperature of the product or component when it is taken out of a furnace or when the heat source is removed or switched off in any other heat treatment, e.g. local heat treatment 3.6 section temperature range temperatu

36、re range with a specified linear distance that may vary between two adjacent measuring points 4 Review of requirements and technical review 4.1 General The manufacturer shall review the contractual requirements and any other requirements together with any technical data. This is to ensure that all i

37、nformation necessary to carry out the heat treatment operations is available prior to the commencement of the work. The manufacturer shall affirm its capability to meet all requirements and ensure adequate planning of all quality-related activities. The review of requirements is carried out by the m

38、anufacturer to verify that the work content is within its capability to perform, that sufficient resources are available to achieve delivery schedules and that documentation is clear and unambiguous. The manufacturer shall ensure that essential variations between the contract and previous quotation

39、are identified. BS EN ISO 17663:2009ISO 17663:2009(E) ISO 2009 All rights reserved 34.2 Review of requirements Aspects for consideration shall include the following: a) product standard used, together with any supplementary requirements; b) statutory and regulatory requirements; c) any additional re

40、quirement determined by the manufacturer; d) capability of the manufacturer to meet the prescribed requirements. 4.3 Technical review It shall be ensured that all necessary information has been supplied by the purchaser. Aspects for consideration shall include the following: a) application standard

41、being used and appropriate drawings; b) location and accessibility of the product or component being heat treated; c) type of marking of the product or component being heat treated; d) heat-treatment specifications (appropriate heat treatment values) and inspection procedures for heat treatment; e)

42、connection between heat-treatment specifications and welding and/or forming-procedure specifications; f) methods of heat treatment, e.g. which products or components are being treated in a furnace and which products or components are being subjected to local heat treatment; g) competence of personne

43、l; h) suitability of equipment; i) heat-treatment documentation; j) control and inspection arrangements; k) quality requirements for the subcontractor; l) handling of non-conformances of heat treatment; m) means of temperature measurement and recording; n) quality requirements and testing of heat tr

44、eatment, if any; o) schedule/sequence of heat treatment; p) availability of sufficient energy; q) other special agreements, e.g. supporting of the product or component. BS EN ISO 17663:2009ISO 17663:2009(E) 4 ISO 2009 All rights reserved5 Subcontracting Any subcontractor shall work under the orders

45、and responsibility of the manufacturer and shall fully comply with the relevant requirements of this International Standard. The manufacturer shall ensure that the subcontractor can comply with the quality requirements of the specification. Information that the manufacturer provides to the subcontra

46、ctor shall include all relevant data from the technical review (see 4.3). The manufacturer who orders heat treatment shall supply all relevant specifications and requirements concerning these works to the subcontractor. The subcontractor shall provide records and documentation of his work as specifi

47、ed by the manufacturer. 6 Personnel The manufacturer shall appoint a sufficient number of competent personnel for the planning, performing and supervising of the heat-treatment work according to specified requirements. The competence of personnel who carry out the heat treatment shall be confirmed b

48、y the manufacturer. The personnel shall be trained and be able to read, understand and implement heat-treatment instructions, e.g. programming the regulation, installation of thermocouples, control of measuring line. 7 Inspection and testing 7.1 General The manufacturer shall have at his disposal a

49、sufficient number of competent personnel for planning and performing, inspection, testing and assessing of the heat-treatment activities according to specified requirements. 7.2 Non-destructive testing Non-destructive testing shall be carried out at the stage of heat treatment specified in the application standard. 7.3 Destructive testing Destructive testing after heat treatment may be carried out if a) it is required by the application standard or contract; b) the manufacturer decides to verify the properties for the product or comp