BS EN ISO 24340-2012 Resilient floor Coverings Determination of thickness of layers《弹性地板覆盖物 层厚度测定》.pdf

1、BRITISH STANDARD BS EN ISO 24340:2012Resilient floor coverings Determination of ICS 97.150nullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnullnullnull nullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnulln

2、ullnullnullnullnullnullnull nullnullnullthickness of layers This British Standard is the UK implementation of EN ISO 24340:2012. It is identical to ISO 24340:2006. It supersedes BS EN 429:1993 and BS ISO 24340:2006, which are withdrawn.The UK participation in its preparation was entrusted to Technic

3、al Committee PRI/60, Resilient floor coverings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with

4、a British Standard cannot confer immunity from legal obligations.BS EN ISO 24340:2012This British Standard waspublished under the authorityof the Standards Policy andStrategy Committeeon 28 April 2006 The British Standards Institution 2012. Published by BSI Standards Limited 2012.Amendments/corrigen

5、da issued since publicationDateComments 31 March 2012 This corrigendum renumbers BS ISO 24340:2006 as BS EN ISO 24340:2012ISBN 978 0 580 75242 1National forewordEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 24340 February 2012 ICS 97.150 Supersedes EN 429:1993English Version Resilient flo

6、or coverings - Determination of thickness of layers (ISO 24340:2006) Revtements de sols rsilients - Dtermination de lpaisseur des couches (ISO 24340:2006) Elastische Bodenbelge - Bestimmung der Dicke der Schichten (ISO 24340:2006) This European Standard was approved by CEN on 24 December 2011. CEN m

7、embers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applic

8、ation to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Mana

9、gement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

10、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploi

11、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 24340:2012: EForeword The text of ISO 24340:2006 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of the International Organization for Standardization (ISO) and has been taken over

12、as EN ISO 24340:2012 by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Au

13、gust 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent

14、 rights. This document supersedes EN 429:1993. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra

15、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 24340:2006 has been approved by CEN as a EN

16、ISO 24340:2012 without any modification. iiiBS EN ISO 24340:2012 EN ISO 24340:2012 (E)1Resilient floor coverings Determination of thickness of layers1 Scope This International Standard describes a method for determining the thickness of different layers of resilient floor coverings. 2 Terms and defi

17、nitions For the purposes of this document, the following terms and definitions apply.2.1 layer component of the same composition as part of a resilient floor coveringwith a given thickness, excludingfactory finishes3 Principle The thickness of layers is measured directly by optical means. 4 Apparatu

18、s 4.1 Microscope or video microscope4.1.1 Microscope or video microscope, having a magnification of at least 40u , equipped with a micrometric scale eyepiece for the microscope or adjustable screen lines for the video microscope, readable to 0,01 mm.4.1.2 Microscope or video microscope, having a mag

19、nification of at least 40u , equipped with an eyepiecemicrometric scale readable to 0,002 5 mm used to measure a thickness below 0,05 mm. 4.2Lamp (light source), to illuminate the specimen configured so that the light falls on the specimen fromas vertical a direction as possible. 4.3 Stage micromete

20、r or video microscope, for calibrating the eyepiece micrometer. The scale shall have the smallest division equal to 0,01 mm and shall cover at least 2,54 mm for the microscope or video microscope referred to in 4.1.1, and the smallest division equal to 0,002 5 mm that covers at least 1 mm for the mi

21、croscope or video microscope referred to in 4.1.2.4.4 Holder (stage carrier), for holding the specimen without distortion, so that the cut edge isperpendicular to the optical axis of the microscope. 4.5 Sharp knife or blade, for cutting the specimen. 4.6 Straightedge or metal rule, for guiding the c

22、utting edge. BS EN ISO 24340:2012 EN ISO 24340:2012 (E)2 5 Sampling and selection of specimens 5.1 Use a fine sharp blade guided by a metal rule or straightedge and keep it perpendicular while cuttingout test pieces. It is veryimportant to cut the specimens face down on a polyamide or similar materi

23、al board toensure a clean edge. 5.2 For sheet floor covering, select five specimens (10 mm u 25 mm) evenly distributed across the width. 5.3 For tile floor covering, select one specimen (10 mm u 25 mm) from each of five separate tiles from thecarton or pack. 6 Atmosphere for conditioning and testing

24、 Condition the specimens for a minimum of 24 h at (23 r 2) C and at a relative humidity of (50 r 5) %, and testin the same environment. 7 Test procedure 7.1 Preparation Place the test piece on the mechanical stage carrier in the holding devi ce, exposing its full thickness (longedge up, the cut surf

25、ace perpendicular to the optical axis of the microscope). 7.2 Calibration Calibrate the micrometer against the stage micrometer and record the calibration factor. 7.3 Measurement Locate the specimen under the microscope and adjust the light source. Focus the microscope so that bothedges of the layer

26、 being measured are sharp. If this cannot be done, remount or re-cut the specimen. Measure the thickness by counting the rulings or the divisions on the ruled disk in the eyepiece (read themeasurement in the case of the video microscope) that cover the distance from one edge of layer to the other,an

27、d by applying the calibration factor determined in 7.2. Record this distance to the nearest graduation on themicroscope or video microscope used. Take three readings in each specimen at least 10 mm apart. Repeat the procedure on the other test specimens. 8 Calculation and expression of results Calcu

28、late the mean thickness for each layer from the number ofmeasurements taken, and express theseresults to the nearest 0,01mm or 0,002 5 mm respective to the microscope or video microscope used. 9 Precision statement An interlaboratory testwill be conducted to determine the precision of this method. B

29、S EN ISO 24340:2012 EN ISO 24340:2012 (E)310 Test report The test report shall include the following information:a) a statement that the tests were performed in accordance with this International Standard (ISO 24340:2006); b) the complete identification of each sample, including type, source, colour

30、, and manufacturers reference numbers;c) the previous history of the sample; d) anydeviation from this International Standard which mayhave affected the results;e) the thickness of the layerof the test specimen, which shall be the mean value calculated to the nearest0,01 mm or 0,002 5 mm respective

31、to the microscope or video microscope used; f) the minimum and maximum readings tothe nearest 0,01 mm or 0,002 5 mm respective to the microscopeor video microscope used. BS EN ISO 24340:2012 EN ISO 24340:2012 (E)4 Bibliography1 EN 429, Resilient floor coverings Determination of the thickness of laye

32、rs2 ASTM F 410, Standard test method for wear layer thickness of resilient floor coverings byopticalmeasurementBS EN ISO 24340:2012 EN ISO 24340:2012 (E)blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and ser

33、vices. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter . British Standards and other standardizationproducts are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High R

34、oad London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our pr

35、oducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.

36、Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standar

37、dsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In respon

38、se to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Knowledge Ce

39、ntre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002

40、 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at the data, software and documentation set out in all British Standards and other BS

41、I publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright

42、, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stan

43、dard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070 Email: