BS EN ISO 6224-2011 Thermoplastics hoses textile-reinforced for general-purpose water applications Specification《一般用途的输水用织物增强的热塑性软管 规范》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 6224:2011Thermoplastics hoses, textile-reinforced, for general-purpose water applications Specification (ISO 6224:2011)BS EN ISO 6224:2011 BRITISH STANDARDNational fore

2、wordThis British Standard is the UK implementation of EN ISO 6224:2011.It supersedes BS EN ISO 6224:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66/-/1, Rubber and plastics tubing, hoses and hoseassemblies - Industrial, chemical and petroche

3、mical applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 65919 5ICS 23.040.70Com

4、pliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NOR

5、M EN ISO 6224 October 2011 ICS 23.040.70 Supersedes EN ISO 6224:2008English Version Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) Tuyaux en matires thermoplastiques armature textile dusage gnral pour leau - Spcifications (ISO 6224:20

6、11)Kunststoffschluche mit Textileinlage fr allgemeine Anwendungen mit Wasser - Anforderung (ISO 6224:2011)This European Standard was approved by CEN on 30 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

7、 Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (E

8、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu

9、m, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMIT

10、TEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6224:2011: EBS EN ISO 6224:2011EN I

11、SO 6224:2011 (E) 3 Foreword This document (EN ISO 6224:2011) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products“ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Sta

12、ndard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the latest by April 2012. Attention is drawn to the possibility that some of the elements of thi

13、s document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 6224:2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countrie

14、s are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia

15、, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 6224:2011 has been approved by CEN as a EN ISO 6224:2011 without any modification. BS EN ISO 6224:2011ISO 6224:2011(E)Contents PageForeword iv1 Scope 12 Normative references .13 Terms and definitions .24 Classifi

16、cation 25 Materials and construction .26 Dimensions .26.1 Inside diameters and tolerances on inside diameter .26.2 Concentricity 36.3 Tolerance on length 36.4 Minimum wall thickness 37 Physical properties .37.1 Thermoplastic materials 37.2 Finished hoses .48 Type, routine and production testing .49

17、Test certificate/report .410 Marking .511 Recommendations for packaging and storage .5Annex A (normative) Type testing and routine testing .6Annex B (informative) Recommended tests for production testing .7 ISO 2011 All rights reserved iiiBS EN ISO 6224:2011ForewordISO (the International Organizatio

18、n for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has

19、 the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Intern

20、ational Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publicatio

21、n as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

22、ISO 6224 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics).This fourth edition cancels and replaces the third edition (ISO 6224:2005), which has been technically revised. The main changes are as follows: Table 1 includes four ad

23、ditional inside diameters (4 mm, 6 mm, 8 mm and 9 mm) for each type of hose; in Table 3, the requirement for the minimum adhesion between components has been raised from 1,5 kN/m to 2,0 kN/m; annexes giving schedules for type, routine and production testing have been added.ISO 6224:2011(E)iv ISO 201

24、1 All rights reservedBS EN ISO 6224:2011INTERNATIONAL STANDARD ISO 6224:2011(E)Thermoplastics hoses, textile-reinforced, for general-purpose water applications SpecificationWARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not pu

25、rport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions.1 ScopeThis International Standard specifies the requirements for gene

26、ral-purpose textile-reinforced thermoplastics water-discharge hoses.Three types of hose are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: ambient temperatures: 10 C to +60 C; water temperature during operation: 0 C to +60 C.NOTE At water t

27、emperatures above 23 C and particularly above 40 C, the maximum working pressure will be reduced.These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as fire-fighting hoses, for special agricultural machines or as gardening hoses for the con

28、sumer market.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3, Preferre

29、d numbers Series of preferred numbersISO 176:2005, Plastics Determination of loss of plasticizers Activated carbon methodISO 188:2011, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance testsISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for m

30、oulding and extrusion plasticsISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 4671, Rubber and plastics hoses and hose assemblies Methods of measu

31、rement of the dimensions of hoses and the lengths of hose assembliesISO 8033, Rubber and plastics hoses Determination of adhesion between componentsISO 8330, Rubber and plastics hoses and hose assemblies VocabularyISO 8331, Rubber and plastics hoses and hose assemblies Guidelines for selection, stor

32、age, use and maintenanceISO 10619-1:1), Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature1) To be published. (Revision of ISO 1746:1998) ISO 2011 All rights reserved 1BS EN ISO 6224:2011ISO 10619-2:2), Rubber and plastics hoses

33、 and tubing Measurement of flexibility and stiffness Part 2: Bending tests at sub-ambient temperaturesISO 30013:2011, Rubber and plastics hoses Methods of exposure to laboratory light sources Determination of changes in colour, appearance and other physical properties3 Terms and definitionsFor the p

34、urposes of this document, the terms and definitions given in ISO 8330 apply.4 ClassificationHoses are designated as one of the following types, depending on their pressure rating:Type 1: Low pressure Designed for a maximum working pressure of 0,6 MPa (6 bar) at 23 C and 0,36 MPa (3,6 bar) at 60 C.Ty

35、pe 2: Medium pressure Designed for a maximum working pressure of 1,0 MPa (10 bar) at 23 C and 0,65 MPa (6,5 bar) at 60 C.Type 3: High pressure Designed for a maximum working pressure of 2,5 MPa (25 bar) at 23 C and 1,6 MPa (16 bar) at 60 C.5 Materials and constructionThe hose shall consist of: a fle

36、xible thermoplastic lining; a reinforcement of natural or synthetic textile, applied by any suitable technique; a flexible thermoplastic cover.The lining and the cover shall be of uniform thickness, concentric, fully gelled and free from visible cracks, porosity, foreign inclusions and other defects

37、. The cover may have a smooth or fluted finish.6 Dimensions6.1 Inside diameters and tolerances on inside diameterWhen measured in accordance with ISO 4671, the inside diameter and its tolerances shall conform to the values specified in Table 1.2) To be published. (Revision of ISO 4672:1997)ISO 6224:

38、2011(E)2 ISO 2011 All rights reservedBS EN ISO 6224:2011Table 1 Inside diameters, tolerances and minimum wall thicknessesInside diameter Tolerance on inside diameterMinimum wall thicknessmmmm mm Type 1 Type 2 Type 34 0,50 2,00 2,00 2,506 0,50 2,00 2,00 2,508 0,60 2,00 2,00 2,809 0,60 2,00 2,00 2,801

39、0 0,75 2,00 2,00 2,8012,5 0,75 2,00 2,50 3,0016 0,75 2,00 2,80 3,0019 0,75 2,20 3,00 3,5025 1,25 2,70 3,50 4,0032 1,25 3,40 4,00 38 1,50 4,00 4,50 50 1,50 5,00 5,50 NOTE 1 For smaller or larger diameters, it is recommended that values be chosen from the R10 series of preferred numbers (see ISO 3), w

40、ith tolerances as specified in ISO 1307.NOTE 2 For intermediate diameters, it is recommended that values be chosen from the R20 series of preferred numbers (see ISO 3).6.2 ConcentricityWhen determined in accordance with ISO 4671, the concentricity, based on a total indicator reading between the insi

41、de diameter and the outside surface of the cover, shall be no greater than 1,0 mm.6.3 Tolerance on lengthWhen measured in accordance with ISO 4671, the tolerance on cut lengths shall be as specified in ISO 1307.6.4 Minimum wall thicknessWhen measured in accordance with ISO 4671, the minimum wall thi

42、ckness of the hose shall conform to the values specified in Table 1. If the cover is fluted, the depth of the flutes shall not be greater than 50 % of the cover thickness.7 Physical properties7.1 Thermoplastic materialsWhen measured by the methods listed in Table 2, the physical properties of the ma

43、terials used for the lining and cover shall conform to the values specified in Table 2.Tests shall be carried out on test pieces taken either from the hose or from separately gelled sheets, 2 mm in thickness.ISO 6224:2011(E) ISO 2011 All rights reserved 3BS EN ISO 6224:2011Table 2 Physical propertie

44、s of thermoplastic materialsProperty Requirements Test methodLining CoverMinimum tensile strength 10,0 MPa 10,0 MPa ISO 527-2 (dumb-bell test piece)Minimum elongation at break 250 % 250 % ISO 527-2 (dumb-bell test piece)Resistance to ageing: ISO 188:2011 (3 days at 70 C 1 C), method A or B;ISO 527-2

45、 (dumb-bell test piece)Change in tensile strength from original value (max.)15 % 15 %Change in elongation at break from original value (max.)25 % 25 %Loss in mass on heating (max.) 4 % 4 % ISO 176:2005, method B7.2 Finished hosesWhen tested at 23 C (standard laboratory temperature) and at 60 C by th

46、e appropriate method specified in ISO 1402, the physical properties of finished hoses shall conform to the values specified in Table 3.8 Type, routine and production testingType tests are those tests carried out to determine that the hose design and method of manufacture meet the full requirements o

47、f this International Standard.Routine tests are those tests carried out on every manufactured length of finished hose.The type tests and routine tests which shall be carried out are given in Annex A.Production tests are those tests carried out on each batch. The tests recommended for production test

48、ing are given in Annex B, which is for guidance only.9 Test certificate/reportWhen requested by the purchaser, the manufacturer or supplier shall provide a test certificate or test report with each length of hose or batch of hoses supplied to the purchaser.ISO 6224:2011(E)4 ISO 2011 All rights reser

49、vedBS EN ISO 6224:2011Table 3 Physical properties of finished hosesProperty Requirements Test methodType 1 Type 2 Type 3MPa bar MPa bar MPa barProof pressure at 23 C 0,9 9 1,5 15 5,0 50 ISO 1402Minimum burst pressure at 23 C 1,8 18 3,0 30 10,0 100 ISO 1402Proof pressure at 60 C 0,55 5,5 0,975 9,75 2,5 25 ISO 1402Minimum burst pressure at 60 C 1,1 11 1,95 19,5 5,0 50 ISO 1402Change in length at maximum working pressure at 23 C8 % ISO 1402Adhesion