BS EN ISO 7051-2011 Cross-recessed raised countersunk (oval) head tapping screws《十字槽半沉头(椭圆头)自攻螺钉》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 7051:2011Cross-recessed raisedcountersunk (oval) headtapping screws (ISO 7051:2011)BS EN ISO 7051:2011 BRITISH STANDARDNational forewordThis British Standard is the UK

2、implementation of EN ISO 7051:2011.It supersedes BS EN ISO 7051:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.

3、This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 68779 2ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published und

4、er the authority of theStandards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7051 August 2011 ICS 21.060.10 Supersedes EN ISO 7051:1994English Version Cross-recessed raised countersunk (

5、oval) head tapping screws (ISO 7051:2011) Vis tle tte fraise bombe empreinte cruciforme (ISO 7051:2011) Linsensenk-Blechschrauben mit Kreuzschlitz (ISO 7051:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations whic

6、h stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Eur

7、opean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members a

8、re the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed

9、en, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

10、Ref. No. EN ISO 7051:2011: EBS EN ISO 7051:2011EN ISO 7051:2011 (E) 3 Foreword This document (EN ISO 7051:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standa

11、rd shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of

12、this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 7051:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count

13、ries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove

14、nia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 7051:2011 has been approved by CEN as a EN ISO 7051:2011 without any modification. BS EN ISO 7051:2011ISO 7051:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardi

15、zation) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to b

16、e represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standa

17、rds are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter

18、national Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7051 wa

19、s prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 13, Fasteners with non-metric thread. This second edition cancels and replaces the first edition (ISO 7051:1983), which has been technically revised. BS EN ISO 7051:2011BS EN ISO 7051:2011INTERNATIONAL STANDARD ISO 7051:2011(E) I

20、SO 2011 All rights reserved 1Cross-recessed raised countersunk (oval) head tapping screws 1 Scope This International Standard specifies the characteristics of cross-recessed raised countersunk (oval) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. 2 Normative references The fo

21、llowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbol

22、s and descriptions of dimensions ISO 1478, Tapping screws thread ISO 2702, Heat-treated steel tapping screws Mechanical properties ISO 3269, Fasteners Acceptance inspection ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners Part 4: Tapping screws ISO 4042, Fasteners E

23、lectroplated coatings ISO 4757, Cross recesses for screws ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 7721, Countersunk head screws Head configuration and gauging ISO 7721-2, Countersunk flat head screws Part 2: Penetration depth of cross

24、recesses ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners BS EN ISO 7051:2011ISO 7051:2011(E) 2 ISO 2011 All rights reserved3 Dimens

25、ions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. a) Type C b) Type F c) Type R d) Type H Cross recess e) Type Z Cross recess aEdge rounded or flat. bDimension a shall be measured at the core diameter of the first full thread. Figure 1 Cross-recessed rai

26、sed countersunk (oval) head tapping screws BS EN ISO 7051:2011ISO 7051:2011(E) ISO 2011 All rights reserved 3Table 1 Dimensions Dimensions in millimetres Thread size ST 2,2 ST 2,9 ST 3,5 ST 4,2 ST 4,8 ST 5,5 ST 6,3 ST 8 ST 9,5Pa0,8 1,1 1,3 1,4 1,6 1,8 1,8 2,1 2,1 a max. 1,6 2,2 2,6 2,8 3,2 3,6 3,6 4

27、,2 4,2 Theoreticalbmax. 4,4 6,3 8,2 9,4 10,4 11,5 12,6 17,3 20,0 max. 3,8 5,5 7,3 8,4 9,3 10,3 11,3 15,8 18,3 dkActual min. 3,5 5,2 6,9 8,0 8,9 9,9 10,9 15,4 17,8 f 0,5 0,7 0,8 1,0 1,2 1,3 1,4 2,0 2,3 k max. 1,10 1,70 2,35 2,60 2,80 3,00 3,15 4,65 5,25 r max. 0,8 1,2 1,4 1,6 2,0 2,2 2,4 3,2 4,0 rf 4

28、,0 6,0 8,5 9,5 9,5 11,0 12,0 16,5 19,5 Recess No 0 1 2 3 4 m ref. 1,9 3,2 4,4 4,6 5,2 6,6 6,8 8,9 10,0 max. 1,2 2,1 2,4 2,6 3,2 3,3 3,5 4,6 5,7 Type H Penetration min. 0,9 1,7 1,9 2,1 2,7 2,8 3,0 4,0 5,1 m ref. 2,0 3,0 4,1 4,4 4,9 6,3 6,6 8,8 9,8 max. 1,20 2,01 2,20 2,51 3,05 3,18 3,45 4,60 5,64 Cro

29、ss recess Type Z Penetration min. 0,95 1,76 1,75 2,06 2,60 2,73 3,00 4,15 5,19 Type C 2,0 2,6 3,2 3,7 4,3 5,0 6,0 7,5 8,0 Type F 1,6 2,1 2,5 2,8 3,2 3,6 3,6 4,2 4,2 y ref. Type R 2,7 3,2 3,6 4,3 5,0 6,3 lcType C and Type R Type F nom. min. max. min. max. 4,5 3,7 5,3 3,7 4,5 6,5 5,7 7,3 5,7 6,5 9,5 8

30、,7 10,3 8,7 9,5 13 12,2 13,8 12,2 13,0 Range 16 15,2 16,8 15,2 16,0 of 19 18,2 19,8 18,2 19,0 preferred 22 21,2 22,8 20,7 22,0 lengths 25 24,2 25,8 23,7 25,0 32 30,7 33,3 30,7 32,0 38 36,7 39,3 36,7 38,0 45 43,7 46,3 43,5 45,0 50 48,7 51,3 48,5 50,0 aP = pitch of the thread. bIn accordance with ISO

31、7721. cSizes with lengths marked with a dash () cannot be manufactured. BS EN ISO 7051:2011ISO 7051:2011(E) 4 ISO 2011 All rights reserved4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel, in accordance wit

32、h ISO 2702 Stainless steel General requirements ISO 8992 Thread ISO 1478 Cross recess ISO 4757, ISO 7721-2 Steel grade/hardness class A2-20H, A4-20H, A5-20H Mechanical propertyInternational Standard ISO 2702 ISO 3506-4 Product grade A Tolerances International Standard ISO 4759-1 As processed Finish

33、Coating Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Requirements for passivation

34、are specified in ISO 16048. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE 1 A cross-recessed raised countersunk (oval) head tapping screw with thread size ST 3,5, nominal length l = 16 mm, made of steel (St) in accordance with ISO 2702, rounded end (Type R) and

35、cross recess Type Z is designated as follows: Tapping screw ISO 7051 - ST 3,5 16 - St - R - Z EXAMPLE 2 A cross-recessed raised countersunk (oval) head tapping screw with thread size ST 3,5, nominal length l = 16 mm, made of stainless steel (A4-20H) in accordance with ISO 3506-4, rounded end (Type R

36、) and cross recess Type H is designated as follows: Tapping screw ISO 7051 - ST 3,5 16 - A4-20H - R - H BS EN ISO 7051:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related pub

37、lications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fa

38、x +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy

39、or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresth

40、at subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international a

41、nd foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwi

42、se requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all

43、its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. T

44、el: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, o

45、f the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior

46、written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: