BS EN ISO 8092-1-1998 Road vehicles - Connections for on-board electrical wiring harnesses - Tabs for single-pole connections - Dimensions and specific requirements《道路车辆 车上电气布线线束的连.pdf

1、BRITISH STANDARD BS EN ISO 8092-1:1998 Road vehicles Connections for on-board electrical wiring harnesses Part 1: Tabs for single-pole connections Dimensions and specific requirements The European Standard EN ISO 8092-1:1998 has the status of a British Standard ICS 43.040.10BSENISO8092-1:1998 This B

2、ritish Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15October1998 BSI 04-1999 ISBN 0 580 30379 9 National foreword This British Standard is the English language version of EN ISO8092-

3、1:1998. It is identical with ISO8092-1:1996. It supersedes BS EN28092-1:1992 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AUE/16, Electrical and electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to

4、 the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obta

5、ined on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these intern

6、ational or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisio

7、ns of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title pag

8、e, page 2, the ISO title page, pages ii to iv, pages 1 to 4, aninsideback cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication

9、 Amd. No. Date CommentsBSENISO8092-1:1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Foreword iii Text of ISO 8092-1 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO8092-1 August1998 ICS 43.040.10 Supersedes EN28092-1:1991 Descriptors: See ISO docume

10、nt English version Road vehicles Connections for on-board electrical wiring harnesses Part 1: Tabs for single-pole connections Dimensions and specific requirements (ISO8092-1:1996) Vhicules routiers Connections pour faisceaux de cblage lectrique embarqus Partie 1: Languettes pour raccordements unipo

11、laires Dimensions et exigences particulires (ISO8092-1:1996) Straenfahrzeuge Steckverbindungen fr das elektrische Fahrzeug-Bordnetz Teil1:Flachstecker fr einpolige Steckverbindungen Mae und besondere Anforderungen (ISO8092-1:1996) This European Standard was approved by CEN on 26 July1998. CEN member

12、s are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

13、 to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the sam

14、e status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee f

15、or Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO8092-1:1998 EENISO8092-1:1998 BSI 04-

16、1999 2 Foreword The text of the International Standard from Technical Committee ISO/TC22 “Road vehicles” of the International Organization for Standardization (ISO) has been taken over as an European Standard by CEN/CS. This European Standard shall be given the status of a national standard, either

17、by publication of an identical text or by endorsement, at the latest by February1999, and conflicting national standards shall be withdrawn at the latest by February1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i

18、mplement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and theUnitedKingdom. This European Standard supersedes EN28092-1:1991. Endorsement notice The t

19、ext of the International Standard ISO8092-1:1996 has been approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normative).ENISO8092-1:1998 ii BSI 04-1999 Contents Page Foreword iii 1 Scope 1 2 Normative reference

20、 1 3 Definitions 1 4 Dimensions 1 5 Specific performance requirements 1 6 Designation 3 Annex A (informative) Examples of single-pole female contacts 4 Annex ZA (normative) Normative references to international publications with their relevant European publications Inside back cover Figure 1 Tab dim

21、ensions 1 Figure A.1 Typical forms 4 Table 1 Tab dimensions 2 Table 2 Performance requirements for connection and disconnection forces of connectors for single-pole connections 2 Table 3 Maximum permitted connection resistance 3 Table A.1 Dimensions 4ENISO8092-1:1998 BSI 04-1999 iii Foreword ISO (th

22、e International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committ

23、ee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechn

24、ical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. International Standard ISO8092-1 was prepared by Tec

25、hnical Committee ISO/TC22, Road vehicles, Subcommittee SC3, Electrical and electronic equipment. This second edition cancels and replaces the first edition (ISO8092-1:1989), of which it constitutes a technical revision. ISO8092 consists of the following parts, under the general title Road vehicles C

26、onnections for on-board electrical wiring harnesses: Part 1: Tabs for single-pole connections Dimensions and specific requirements; Part 2: Definitions, test methods and general performance requirements; Part 3: Tabs for multi-pole connections Dimensions and specific requirements; Part 4: Pins for s

27、ingle- and multi-pole connections Dimensions and specific requirements. Annex A of this part of ISO8092 is for information only. Descriptors: Road vehicles, electrical installation, cable harnesses, electric connections, electric connectors, single-pole connectors, plug connectors, connector feather

28、s, specifications, dimensions.iv blankENISO8092-1:1998 BSI 04-1999 1 1 Scope This part of ISO8092 specifies dimensions for the tabs of single-pole connections and specific requirements, for on-board electrical wiring harnesses of road vehicles, which can be fitted into female contacts such as those

29、given in Annex A. It applies to connectors designed to be disconnected after mounting in the vehicle for the purposes of repair and/or maintenance only. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this part of ISO80

30、92. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this part of ISO8092 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO ma

31、intain registers of currently valid International Standards. ISO8092-2:1996, Road vehicles Connections for on-board electrical wiring harnesses Part2:Definitions, test methods and general performance requirements. 3 Definitions For the purposes of this part of ISO8092, the definitions given in ISO80

32、92-2 apply. 4 Dimensions Tabs for single-pole connections shall conform to the dimensions given in Table 1 and Figure 1. Details not specified are left to the manufacturers choice. 5 Specific performance requirements Single-pole connections shall be in conformity with the general performance require

33、ments of ISO8092-2, and shall meet the following specific requirements. 5.1 Design requirements A tab without detent requires external means of retention to the mating part. If tabs are stamped or stamped and formed, the usable contact area shall be specified and care shall be taken to assure that g

34、aps, seams and rounded edges do not affect the contact performance. 5.2 Connection forces and disconnection forces Connectors for single-pole connections, tested in accordance with ISO8092-2:1995, subclause4.3 shall meet the requirements in Table 2. Figure 1 Tab dimensionsENISO8092-1:1998 2 BSI 04-1

35、999 Table 1 Tab dimensions Table 2 Performance requirements for connection and disconnection forces of connectorsfor single-pole connections Dimensions in millimetres Dimension Size a 2,8 0,5 2,8 0,8 4,8 0,5 4,8 0,8 6,3 0,8 9,5 1,2 l 1 min. 8,1 8 10,1 14,5 l 2 max. 0,6 0,9 1,0 1,3 min. 0,3 0,6 0,5 0

36、,7 l 3 max. 7,3 6,5 8,1 12,5 min. 7,0 6,2 7,8 12,0 l 4 b max. 1,8 3,4 4,7 5,5 min. 1,3 3,0 4,0 4,5 b 1 max. 2,9 4,9 6,4 9,6 min. 2,7 4,7 6,2 9,4 b 2 max. 2,3 3,5 4,7 6,5 min. 2,0 3,0 3,7 5,5 c 1 max. 0,54 0,84 0,54 0,84 0,84 1,23 min. 0,47 0,77 0,47 0,77 0,77 1,17 c 2 max. 0,3 0,5 0,3 0,5 0,5 0,7 mi

37、n. 0,1 0,3 0,1 0,3 0,3 0,5 x 0,2 y 0,07 0,06 D b max. 1,3 1,5 2 min. 1,1 1,3 1,6 1,7 a Recommended tab sizes are shown in bold type. b For tabs with detent only. Connection and disconnection Force, N Tab size 2,8 4,8 6,3 9,5 P a F b P F P F F First connection force max. 27 53 30 67 45 80 100 First d

38、isconnection force max. 27 53 30 67 45 80 100 10th disconnection force min. 4 6 7 15 9 18 30 a P refers to positive locking female contact. b F refers to female contact without positive locking.ENISO8092-1:1998 BSI 04-1999 3 5.3 Connection resistance Single-pole connections, tested in accordance wit

39、h ISO8092-2:1995, subclause4.8, shall meet the requirements in Table 3. Table 3 Maximum permitted connection resistance 6 Designation Tabs in accordance with this part of ISO8092 shall be designated as follows. EXAMPLE Connection resistance Initial After endurance a a m7 m7 % of initial measured val

40、ue max. max. max. 5 10 150 a As selected by supplier and user.ENISO8092-1:1998 4 BSI 04-1999 Annex A (informative) Examples of single-pole female contacts This annex shows examples in Figure A.1 of single-pole female contact designs and reference dimensions in Table A.1. All other designs that meet

41、the performance requirements specified in ISO8092-2 are acceptable. Table A.1 Dimensions Figure A.1 Typical forms Dimensions in millimetres Size Type l 1 c 1 b 1 2,8 1 2 6,4 8,9 2,2 4,6 3,8 3,9 4,8 1 2 6,4 8,9 2,5 4,2 5,8 5,6 6,3 1 2 7,8 8,9 3,2 4,2 7,7 7,2 9,5 1 2 12 3,8 11 ENISO8092-1:1998 BSI 04-

42、1999 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and

43、 the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Pu

44、blication Year Title EN Year ISO8092-2 1996 Road vehicles Flat, quick-connect terminations Part 2: Test and performance requirements for single pole connections EN ISO8092-2 1998BS EN ISO 8092-1:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent natio

45、nal body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the l

46、atest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which

47、 can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards pub

48、lications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI p

49、rovides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standa