BS EN ISO 8745-1998 Grooved pins - Half-length taper grooved《带槽销 半长锥槽型销》.pdf

1、BRITISH STANDARD BS EN ISO 8745:1998 Grooved pins Half-length taper grooved The European Standard EN ISO 8745:1997 has the status of a British Standard ICS 21.060.50BSENISO8745:1998 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe

2、authority of the Standards Board and comes intoeffect on 15 May 1998 BSI 04-1999 ISBN 0 580 29060 3 National foreword This British Standard is the English language version of EN ISO 8745:1997. It is identical with ISO 8745:1997. It supersedes BS EN 28745:1992 which is withdrawn. The UK participation

3、 in its preparation was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General purpose fasteners and accessories, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enqu

4、iries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Atte

5、ntion is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document

6、 may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of Briti

7、sh Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, page 2, the ISO title page, p

8、age ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN ISO 8745:

9、1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Foreword ii Text of ISO 8745:1997 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8745 November 1997 ICS 21.060.50 Supersedes EN 28745:1992 Descriptors: See ISO document English version Grooved pins Ha

10、lf-length taper grooved (ISO 8745:1997) Goupilles canneles cannelures progressives sur la moiti de la longueur (dbouchantes) (ISO 8745:1997) Pakerbstifte (ISO 8745:1997) This European Standard was approved by CEN on 23 October 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regul

11、ations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Eu

12、ropean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the na

13、tional standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisc

14、hes Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8745:1997 EENISO8745:1997 BSI 04-1999 2 Foreword The text of the International Standard ISO874

15、5:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by DIN. This European Standard supersedes EN 28745:1992. This European Standard

16、 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998. According to the CEN/CENELEC Internal Regulations, the national standards organ

17、izations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The

18、 text of the International Standard ISO 8745:1997 has been approved by CEN as a European Standard without any modifications. NOTENormative references to International Standards are listed in Annex ZA (normative). Contents Page Foreword 1 1 Scope 1 2 Normative references 1 3 Dimensions 1 4 Applicatio

19、n 3 5 Requirements and reference International Standards 3 6 Designation 4 Annex ZA (normative) Normative references to international publicationswiththeirrelevant Europeanpublication Inside back cover Figure 1 1 Table 1 Dimensions 2 Table 2 Requirements and reference International Standards 3ENISO8

20、745:1997 ii BSI 04-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in

21、 a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commiss

22、ion (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Internation

23、al Standard ISO 8745 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and replaces the first edition (ISO 8745:1986), which has been technically revised. Descriptors: Fasteners, steel products, pins (mechanics), grooved pins, specifications, characteristics, dimen

24、sions, designation.ENISO8745:1997 BSI 04-1999 1 1 Scope This International Standard specifies the characteristics of half-length taper grooved pins made of steel or austenitic stainless steel which have three equally spaced grooves impressed longitudinally on their exterior surface, with nominal dia

25、meter, d 1 , from 1,5mm to 25mm inclusive. The displaced material to each side of the grooves forming an expanded diameter, d 2 , which is larger than the nominal diameter d 1will cause a non-positive locking fit when these grooved pins are forced into a drilled hole equal to the nominal diameter d

26、1 , (see clause4). 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agree

27、ments based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3269:1988, Fasteners Acceptance inspection. ISO 35

28、06-1:1997, Corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs. ISO 4042: 1) , Fasteners Electroplated coatings. ISO 8749:1986, Pins and grooved pins Shear test. ISO 9717:1990, Phosphate conversion coatings for metals Method of specifying requirements. 3 Dimensions See Figu

29、re 1 and Table 1. 1) To be published. (Revision of ISO 4042:1989) Figure 1 ENISO8745:1997 2 BSI 04-1999 Table 1 Dimensions Dimensions in millimetres d 1 nom. 1,5 2 2,5 3 4 5 6 8 10 12 16 20 25 tol. h9 h11 a . 0,2 0,25 0,3 0,4 0,5 0,63 0,8 1 1,2 1,6 2 2,5 3 Minimum shear strength, double akN 1,6 2,84

30、 4,4 6,4 11,3 17,6 25,4 45,2 70,4 101,8 181 283 444 l b Expanded diameter, d 2 c , d nom. min. max. 0,05 0,1 8 7,75 8,25 10 9,75 10,25 2,65 3,2 4,25 5,25 12 11,5 12,5 1,63 14 13,5 14,5 3,25 6,25 8,25 16 15,5 16,5 4,3 5,3 10,3 18 17,5 18,5 2,15 8,3 12,3 20 19,5 20,5 2,7 6,3 22 21,5 22,5 10,35 12,35 2

31、4 23,5 24,5 3,3 26 25,5 26,5 28 27,5 28,5 4,35 8,35 16,5 30 29,5 30,5 5,35 32 31,5 32,5 10,4 12,4 20,55 25,5 35 34,5 35,5 3,25 6,35 40 39,5 40,5 16,55 45 44,5 45,5 50 49,5 50,5 4,3 55 54,25 55,75 5,3 8,4 60 59,25 60,75 65 64,25 65,75 10,45 12,45 70 69,25 70,75 6,3 75 74,25 75,75 80 79,25 80,75 16,6

32、85 84,25 85,75 90 89,25 90,75 8,35 20,6 25,6 95 94,25 95,75 10,4 12,4 100 99,25 100,75 120 119,25 120,75 140 139,25 140,75 160 159,25 160,75 10,35 12,35 16,55 180 179,25 180,75 200 199,25 200,75 a Applies only to grooved pins made from steel as shown in clause 5. b The range of commercial lengths is

33、 between the stepped lines. c The expanded diameter d 2applies only to pins made from steel as shown in clause 5. For other materials, for example stainless steel, a reduction amount shall be subtracted from the given values and should be agreed between customer and supplier. d For testing d 2 , a G

34、O/NO GO ring gauge should be used. + 0,05 0ENISO8745:1997 BSI 04-1999 3 4 Application The diameter of the hole into which the groove pin is to be inserted shall be equal to the nominal diameter d 1of the mating pin and to tolerance class H11. 5 Requirements and reference International Standards SeeT

35、able 2. Table 2 Requirements and reference International Standards Steel (St) Austenitic stainless steel Material a Hardness 125 HV30 to 245 HV30 A1 in accordance with ISO 3506-1, hardness 210 HV30 to 280 HV30 Grooves Form of groove at the discretion of the supplier. Plain, i.e. pins to be supplied

36、in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and supplier. Surface finish Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conversion coating (see ISO 9717 and ISO 4042). Plain, i.e. pins to be supp

37、lied in natural finish. Other coatings as agreed between customer and supplier. All tolerances shall apply prior to the application of a plating or coating. Workmanship Pins shall be free of irregularities or detrimental defects. Shear strength test The test shall be in accordance with ISO 8749. Acc

38、eptability The acceptance procedure is covered in ISO 3269. a Other materials as agreed between customer and supplier.ENISO8745:1997 4 BSI 04-1999 6 Designation EXAMPLE 1 A half-length taper grooved steel pin with nominal diameter d 1 , = 6 mm and nominal length l = 50 mm is designated as follows: G

39、rooved pin ISO 8745 6 50 St EXAMPLE 2 A half-length taper grooved austenitic stainless steel pin of grade A1, with nominal diameter d 1 ,=6mm and nominal lengthl = 50mm is designated as follows: Grooved pin ISO 8745 6 50 A1ENISO8745:1997 BSI 04-1999 Annex ZA (normative) Normative references to inter

40、national publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references cited at the appropriate places in the text and the publications are listed hereafter. For dated reference

41、s, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title EN Year ISO 8749 1986 Pins and grooved

42、 pins Shear test EN 28749 1992 ISO 3506-1 1997 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs EN ISO 3506-1 1997BS EN ISO 8745:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body res

43、ponsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendm

44、ents or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be foun

45、d on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications sh

46、ould be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wi

47、de range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:020899671

48、11. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsi

49、sts in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols,