1、BRITISH STANDARD BS EN ISO 9222-2:1995 BS 308-1.15: 1995 Technical drawings Seals for dynamic application Part 2: Detailed simplified representation The European Standard EN ISO 9222-2:1995 has the status of a British StandardBSENISO9222-2:1995 This British Standard, having been prepared under the d
2、irectionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 September 1995 BSI 02-1999 The following BSI references relate to the work on this standard: Committee reference TDE/4 Draft announced in BSI News August1995 ISBN 0 580 23764 8
3、 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office
4、 Material Manufacturers and Dealers Association Electricity Association Gauge and Tool Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Companies Ltd. University of Warwic
5、k Amendments issued since publication Amd. No. Date CommentsBSENISO9222-2:1995 BSI 02-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Introduction 3 1 Scope 3 2 Normative references 3 3 Method of representation 4 4 Examples 11 Figure 1 Rotary shaft lip
6、type seal (sealing against fluids) 11 Figure 2 Rotary shaft lip type seal with dust lip 12 Figure 3 Packing set 12 Figure 4 V-ring 13 Figure 5 Labyrinth seal 13 Table 1 Elements of detailed simplified representation for seals 4 Table 2 Detailed simplified representation 6 Table 3 Detailed representa
7、tion of U-caps, packing sets and U-rings 10 Table 4 Detailed simplified representation of labyrinth seals (irrespective of the number of labyrinths) 11 List of references Inside back coverBSENISO9222-2:1995 ii BSI 02-1999 National foreword This British Standard has been prepared by Technical Committ
8、ee TDE/4 and is the English language version of EN ISO9222-2:1994 Technical drawings Seals for dynamic application Part 2: Detailed simplified representation, published by the European Committee for Standardization (CEN). It is identical with ISO9222-2:1989 published by the International Organizatio
9、n for Standardization (ISO). This Part of BS EN ISO9222 partially supersedes BS308-1. It is envisaged that when the full range of European Standards on technical drawing is implemented BS308 will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract.
10、 Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard ISO 5597:1987 BS5751:1987 Specification for dimensions of h
11、ousings for hydraulic seals for reciprocating applications ISO 6194-1:1982 BS7780 Specification for rotary shaft lip type seals Part 1:1994 Nominal dimensions and tolerances ISO 6547-1:1981 BS 6241:1982 Specification for dimensions of housings for hydraulic seals incorporating bearing rings for reci
12、procating applications ISO 9222-1:1989 BS EN ISO 9222 Technical drawings Seals for dynamic application Part 1:1995 General simplified representation Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, pages2 to 14, an inside back cover
13、 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9222-2 October 1994 ICS 01.100.20; 21.140 Descriptors: Draw
14、ings, technical drawings, seals (stoppers), graphic methods English version Technical drawings Seals of dynamic application Part 2: Detailed simplified representation (ISO 9222-2:1989) Dessins techniques Joints dtanchit pour application dynamique Partie 2: Reprsentation simplifie particulire (ISO 92
15、22-2:1989) Technische Zeichnungen Dichtungen fr dynamische Belastung Teil 2: Detaillierte, vereinfachte Darstellung (ISO 9222-2:1989) This European Standard was approved by CEN on1994-10-14. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
16、giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official v
17、ersions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu
18、m, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassa
19、rt 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN ISO 9222-2:1994 EENISO9222-2:1994 BSI 02-1999 2 Foreword This European Standard was taken over by CEN from the work of ISO/TC10 Technical drawings, product definitions and related documentation, of the International Standards
20、Organization (ISO). The Technical Board had decided to submit the final draft for Formal Vote. The result was positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April1995, and conflicting n
21、ational standards shall be withdrawn at the latest by April1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, No
22、rway, Portugal, Spain, Sweden, Switzerland, United Kingdom.ENISO9222-2:1994 BSI 02-1999 3 Introduction ISO 9222 provides rules for the simplified representation of seals. The principle of drawing practice is to depict the object to scale using lines. In simplified representations, only essential fea
23、tures are shown, preferably in outline (in order to save time and effort). The degree of simplification depends on the kind of object represented, the scale of the drawing and the purpose of the documentation. This means that either a general simplified representation or a detailed one may be used.
24、A detailed representation shows more details of a seal, for example the configuration of lips. In order to avoid misunderstandings, only one kind of simplification, either the general or the detailed simplified representation, should be used on a drawing. 1 Scope This part of ISO9222 specifies a det
25、ailed simplified representation for various seals. This representation should be used in cases where it is not necessary to show the exact shape and details of the seals, for example in assembly drawings. 2 Normative references The following standards contain provisions which, through reference in t
26、his text, constitute provisions of this part of ISO9222. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO9222 are encouraged to investigate the possibility of applying the most recent editions of
27、 the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO5597:1987, Hydraulic fluid power Cylinders Housings for piston and rod seals in reciprocating applications Dimensions and tolerances. ISO6194-1:1982, Rotary shaft lip seals Part 1
28、: Nominal dimensions and tolerances. ISO6547:1981, Hydraulic fluid power Cylinders Piston seal housings incorporating bearing rings Dimensions and tolerances. ISO9222-1:1989, Technical drawings Seals for dynamic application Part 1: General simplified representation.ENISO9222-2:1994 4 BSI 02-1999 3 M
29、ethod of representation 3.1 General rules See ISO9222-1. 3.2 Elements of detailed simplified representation for seals The elements of detailed simplified representation for seals are given in Table 1. Table 1 Elements of detailed simplified representation for seals No. Element Description Applicatio
30、n 1.1 Long continuous straight line (parallel to a generating line of the sealing surface) The static (pressed in, fixed) element (seal or part of the seal or function) 1.2 Long continuous straight line (diagonal to the outlines) a The dynamic sealing element (lip) or function (part of the seal) In
31、conjunction with symbol No. 1.1, it shows the position of the dynamic sealing side directed against fluids, gases and solid media 1.3 Short continuous straight line (diagonal to the outlines and at 90 to symbol No. 1.2) a In combination with symbol No. 1.2, dust lips, wipers, etc. 1.4.1 Short contin
32、uous angular line pointing to the centre point of the square a Sealing lips of U-cups, V-rings, packing sets, etc.ENISO9222-2:1994 BSI 02-1999 5 Table 1 Elements of detailed simplified representation for seals No. Element Description Application 1.4.2 Short continuous straight line pointing to the c
33、entre point of the square a Like 1.4.1 for U-cups, V-rings, packing sets, etc. 1.5 T (male) (T in U) Contactless seals, for example labyrinth seals 1.6 U (female) a An arrowhead may be added to show the sealing direction.ENISO9222-2:1994 6 BSI 02-1999 3.3 Detailed simplified representation The detai
34、led simplified representations of seals are shown in Table 2 to Table 4. NOTE Seals shown in Table 2 to Table 4 are always depicted in the space above the axis. Table 2 Detailed simplified representation No. Detailed simplified representation Application Seals subject to rotation Relevant Internatio
35、nal Standard 2.1 Rotary shaft lip type seals without dust lip Mechanical seals ISO 6194-1 2.2 Rotary shaft lip type seals without dust lip Mechanical seals ISO 6194-1ENISO9222-2:1994 BSI 02-1999 7 Application Illustration a Seals subject to translation Relevant International Standard Piston rod seal
36、s without wiper ISO 5597 Piston rod seals without wiper ISO 5597 a This type of illustration is not commonly used in technical drawings, but is used conventionally in catalogues, users handbooks, prospectuses, etc.ENISO9222-2:1994 8 BSI 02-1999 Table 2 Detailed simplified representation No. Detailed
37、 simplified representation Application Seals subject to rotation Relevant International Standard 2.3 Rotary shaft lip type seals with dust lip ISO 6194-1 2.4 Rotary shaft lip type seals with dust lip ISO 6194-1 2.5 Rotary shaft lip type seals without dust lip, double-acting Mechanical seals 2.6 Rota
38、ry shaft lip type seals without dust lip, double-acting Mechanical seals ENISO9222-2:1994 BSI 02-1999 9 Application Illustration a Seals subject to translation Relevant International Standard Piston rod seals with wiper Piston rod seals with wiper Double-acting piston rod seals Double-acting piston
39、rod seals ISO 6547 a This type of illustration is not commonly used in technical drawings, but is used conventionally in catalogues, users handbooks, prospectuses, etc.ENISO9222-2:1994 10 BSI 02-1999 Table 3 Detailed representation of U-cups, packing sets and V-rings No. Detailed simplified represen
40、tation Application 3.1 3.2 3.3 3.4 3.5 3.6 3.7ENISO9222-2:1994 BSI 02-1999 11 Table 4 Detailed simplified representation of labyrinth seals (irrespective of the numberoflabyrinths) 4 Examples Examples showing the simplified representation of seals are given in Figure 1 to Figure 5. No. Detailed simp
41、lified representation Application 4.1 Figure 1 Rotary shaft lip type seal (sealing against fluids)ENISO9222-2:1994 12 BSI 02-1999 Figure 2 Rotary shaft lip type seal with dust lip Figure 3 Packing setENISO9222-2:1994 BSI 02-1999 13 Figure 4 V-ring Figure 5 Labyrinth seal14 blankBSENISO9222-2:1995 BS
42、I 02-1999 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
43、| | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Stan
44、dards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while usin
45、g this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically
46、receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI impl
47、ementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic i
48、nformation services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of st
49、andards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1