BS EN ISO 9431-1999 Construction drawings Spaces for drawing and for text and title blocks on drawing sheets《建筑图纸 图和正文的间隔 图纸上的标题栏》.pdf

1、BRITISH STANDARD BS EN ISO 9431:1999 Construction drawings Spaces for drawing and for text, and title blocks on drawing sheets ICS 01.100.30BSENISO9431:1999 This British Standard, having been prepared under the directionof the Sector Committeefor Building andCivilEngineering, waspublishedunder theau

2、thorityofthe StandardsCommittee and comesinto effect on 15October1999 BSI 04-2000 ISBN 0 580 35114 9 National foreword This British Standard reproduces verbatim ISO 9431:1990 and implements itas the UK national standard. This standard, together with BS EN ISO 4157-1:1999, BS EN ISO 4157-2:1999, BS E

3、N ISO 4157-3:1999, BSEN ISO 6284:1999 and BS EN ISO 8560:1999 supersedes, BS 1192-1:1984 which is withdrawn. The UK participation in its preparation was entrusted by Technical CommitteeB/212, Tolerances, drawing practice, modular co-ordination, joints, project information and computer modelling, to

4、Subcommittee B/212/2, Construction drawing practice, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related in

5、ternational and European developments and promulgate them in the UK. A list of organizations represented on this Subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be

6、 found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Stan

7、dards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, page 2, the ISO title page, pages ii

8、 to iv, pages 1 to 5 anda back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSENISO9431:1999 BSI 04-2000 i Conten

9、ts Page National foreword Inside front cover Foreword 2 Foreword iii Text of ISO9431 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9431 July 1999 ICS 01.100.00 English version Construction drawings Spaces for drawing and for text, and title blocks on drawing sheets (ISO 9431:1990

10、) Dessins de construction Zones rserves au dessin et au texte, et cartouches dinscription sur les feuilles de dessin (ISO 9431:1990) Zeichnungen fr das Bauwesen Anordnung von Darstellungen, Texten und Schriftfeldern auf Zeichnungsvordrucken (ISO 9431:1990) This European Standard was approved by CEN

11、on 1 July 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

12、be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Centr

13、al Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

14、 CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9431:1999 E

15、ENISO9431:1999 BSI 04-2000 2 Foreword The text of the International Standard from Technical Committee ISO/TC 10 “Technical drawings, product definition and related documentation” of the International Organization for Standardization (ISO) has been taken over as an European Standard by CEN/CS. This E

16、uropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2000, and conflicting national standards shall be withdrawn at the latest by January 2000. According to the CEN/CENELEC Internal Regulations, the

17、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom

18、. Endorsement notice The text of the International Standard ISO9431:1990 has been approved by CEN as a European Standard without any modification.ENISO9431:1999 ii BSI 04-2000 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 General layout 1 4 Space for drawing 1 5 Space for text 1 An

19、nex A (informative) Bibliography 5 Figure 1 2 Figure 2 2 Figure 3 2 Figure 4 2 Figure 5 2 Figure 6 3 Figure 7 3 Figure 8 3 Figure 9 4 Descriptors: Construction, drawings, technical drawings, spacing, title blocks.ENISO9431:1999 BSI 04-2000 iii Foreword ISO (the International Organization for Standar

20、dization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to

21、 be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft Internationa

22、l Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. International Standard ISO 9431 was prepared by Technical Committee ISO/TC10, Technical draw

23、ings, product definition and related documentation. Annex A of this International Standard is for information only.iv blankENISO9431:1999 BSI 04-2000 1 1 Scope This International Standard specifies requirements concerning the placing, layout and contents of spaces for drawing and for text, and title

24、 blocks on construction drawings. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and p

25、arties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3098-1:1974, Technical drawings Let

26、tering Part 1: Currently used characters. ISO 7200:1984, Technical drawings Title blocks. 3 General layout (see Figure 1 and Figure 2) The space on a drawing sheet is primarily divided into a space for drawing (see clause 4); a space for text (see clause 5); a title block (see ISO 7200). 4 Space for

27、 drawing The figures comprising a drawing shall be arranged in horizontal rows and vertical columns. A main figure, if one is identified as such, shall be placed at the top left of the drawing or at the top left of a group of figures. If possible, consideration shall be taken ofA4-size folds of a dr

28、awing sheet when figures are drawn. 5 Space for text 5.1 General The space for text on a drawing sheet shall contain all information necessary for the understanding of the contents of the drawing (see 5.2), except for the text which needs to be placed adjacent to the figures in the space for drawing

29、. The space for text shall normally be placed at the right-hand edge of the drawing sheet (see Figure 1); the width of the space shall be equal to that of the title block, i.e.maximum 170mm, or at least100mm. If a figure takes up the whole width of the drawing sheet, the space for text shall be plac

30、ed at the bottom edge of the drawing sheet (seeFigure 2); the height of the space shall be chosen as required. The space for text shall be divided into columns of appropriate width; if possible, account shall be taken of folds in a folded drawing when deciding on column width. 5.2 Information to be

31、placed in space for text 5.2.1 General The following information is normally placed in the space for text: explanations (see 5.2.2); instructions (see 5.2.3); references (see 5.2.4); location figure (see 5.2.5); revision table (see 5.2.6). 5.2.2 Explanations Under “Explanations”, information shall b

32、e givenwhich is needed to read the drawing, e.g.explanations of special symbols, designations, abbreviations and units of dimensions. 5.2.3 Instructions Under “Instructions”, information, supplementary to the information in the space for drawing, shall be given which is needed to perform what is sho

33、wn on the drawing, e.g. instructions relating to material, realization, surface treatment, assembly placing, number of units and combined dimensions. If several objects are shown on the drawing, general instructions shall be placed in the space for text and special instructions shall be placed adjac

34、ent to the relevant figures. 5.2.4 References Under “References”, reference shall be made to supplementary drawings and other documents. 5.2.5 Location figure A location figure shall be placed so that it remains visible after the drawing has been folded. A location figure shall comprise, as required

35、, the following figures: schematic site plan with area, arrow indicating the north, building, part of building, etc. marked (see Figure 3); schematic plan of building with area, part, etc. indicated (see Figure 4); schematic section through building with floor plan, direction of view, etc. indicated

36、 (see Figure 5).ENISO9431:1999 2 BSI 04-2000 5.2.6 Revision table A revision table shall be used to record all revisions such as corrections and/or amendments following the first issue. In addition, any other factor which might influence the validity of the drawing shall be recorded in the revision

37、table. A revision table shall contain the following information: designations of revision and, if required, number of places where correction has been made; details concerning the revision; date of revision; signature of person responsible for revision. The width of the revision table shall be equal

38、 to either a) the width of the title block, if the revision table is placed immediately above the title block, b) at least 100 mm, if the revision table is placed to the left of the title block. The height of each line in the revision table shall be in accordance with the rules given in ISO 3098-1 a

39、nd shall meet the minimum requirement for spacing of base lines. An example of the layout of a revision table is illustrated in Figure 6. 5.3 Layout Examples of the layout of the space for text on the drawing sheet are given in Figure 7, Figure 8 and Figure 9. Figure 1 Figure 2 Figure 3 Figure 4 Fig

40、ure 5 ENISO9431:1999 BSI 04-2000 3 Figure 6 Figure 7 Figure 8 ENISO9431:1999 4 BSI 04-2000 Figure 9 ENISO9431:1999 BSI 04-2000 5 Annex A (informative) Bibliography 1 ISO 128:1982, Technical drawings General principles of presentation. 2 ISO 5457:1980, Technical drawings Sizes and layout of drawing s

41、heets. 3 ISO 8048:1984, Technical drawings Construction drawings Representation of views, sections and cuts.BS ENISO 9431:1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK v

42、iew on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve th

43、e quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400

44、. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:

45、02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internation

46、al standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up t

47、o date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in

48、 the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise witho

49、ut prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.