1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 4: Solderable polyurethane enamelled round copper wire, class 130BS IEC 60317-4:2015National forewordThis British Standard is the UK implementation of IEC 60317-4:2015. Itsupersedes BS EN 60317-4:1995 which is withdraw
2、n.The UK participation in its preparation was entrusted to TechnicalCommittee L/-/99, Miscellaneous Standards - Electrical.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa co
3、ntract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83424 0ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the au
4、thority of theStandards Policy and Strategy Committee on 31 July 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 60317-4:2015IEC 60317-4 Edition 4.0 2015-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Pa
5、rt 4: Solderable polyurethane enamelled round copper wire, class 130 Spcifications pour types particuliers de fils de bobinage Partie 4: Fil brasable de section circulaire en cuivre maill avec polyurthane, classe 130 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONAL
6、E ICS 29.060.10 ISBN 978-2-8322-2729-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous a
7、vez obtenu cette publication via un distributeur agr. BS IEC 60317-4:2015 2 IEC 60317-4:2015 IEC 2015 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes . 6 3.2.1 Methods of tes
8、t 6 3.2.2 Winding wire 6 3.2.3 Appearance . 7 4 Dimensions . 7 5 Electrical resistance 7 6 Elongation . 7 7 Springiness . 7 8 Flexibility and adherence . 7 9 Heat shock 7 10 Cut-through . 7 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,000 mm) 7 12 Resist
9、ance to solvents . 8 13 Breakdown voltage 8 14 Continuity of insulation 8 15 Temperature index . 8 16 Resistance to refrigerants 8 17 Solderability 8 17.1 Nominal conductor diameters up to and including 0,100 mm . 8 17.2 Nominal conductor diameter over 0,100 mm 9 18 Heat or solvent bonding . 9 19 Di
10、electric dissipation factor 9 20 Resistance to transformer oil . 9 21 Loss of mass . 9 23 Pin hole test 9 30 Packaging . 9 Bibliography . 10 Table 1 Resistance to abrasion 8 BS IEC 60317-4:2015IEC 60317-4:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES
11、 OF WINDING WIRES Part 4: Solderable polyurethane enamelled round copper wire, class 130 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is
12、 to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and
13、 Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the
14、IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly a
15、s possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sen
16、se. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees und
17、ertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any at
18、testation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest editio
19、n of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direc
20、t or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensab
21、le for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-4 has
22、been prepared by IEC technical committee 55: Winding wires. This fourth edition cancels and replaces the third edition published in 1990, Amendment 1:1997 and Amendment 2:1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respe
23、ct to the previous edition: new 3.2.2 containing general notes on winding wire, formerly a part of the scope; new 3.2.3 containing requirements for appearance; revision to references to IEC 60317-0-1:2013 to clarify that their application is normative; consolidation of 17.1 and 17.2 of the solderabi
24、lity requirements; revision to Clause 19, dielectric dissipation factor; new Clause 23, pin hole test. BS IEC 60317-4:2015 4 IEC 60317-4:2015 IEC 2015 The text of this standard is based on the following documents: CDV Report on voting 55/1459/CDV 55/1498/RVC Full information on the voting for the ap
25、proval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This International Standard is to be read in conjunction with IEC 60317-0-1:2013. The numbering of clauses in this standard
26、is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. A list of all parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires, can be found on the IEC web
27、site. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by
28、a revised edition, or amended. BS IEC 60317-4:2015IEC 60317-4:2015 IEC 2015 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851 series); 2
29、) Specifications for particular types of winding wires (IEC 60317 series); 3) Packaging of winding wires (IEC 60264 series). BS IEC 60317-4:2015 6 IEC 60317-4:2015 IEC 2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 4: Solderable polyurethane enamelled round copper wire, class 130 1 S
30、cope This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 130 with a sole coating based on polyurethane resin, which may be modified provided it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE
31、 A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: Grade 1: 0,018 mm up to and including 2,000 mm; Grade 2: 0,020 mm
32、up to and including 2,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the ed
33、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1:2013, Specifications for particular types of winding wires Part 0-1: General requirements Enamelled round copper wire 3 Terms, definitions, general notes and a
34、ppearance 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in 3.1 of IEC 60317-0-1:2013 apply. 3.2 General notes 3.2.1 Methods of test Subclause 3.2 of IEC 60317-0-1:2013 applies. In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 6031
35、7-4 shall prevail. 3.2.2 Winding wire Class 130 is a thermal class that requires a minimum temperature index of 130 and a heat shock temperature of at least 155 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wi
36、re be operated and this will depend on many factors, including the type of equipment involved. BS IEC 60317-4:2015IEC 60317-4:2015 IEC 2015 7 3.2.3 Appearance Subclause 3.3 of IEC 60317-0-1:2013 applies. 4 Dimensions Clause 4 of IEC 60317-0-1:2013 applies. 5 Electrical resistance Clause 5 of IEC 603
37、17-0-1:2013 applies. 6 Elongation Clause 6 of IEC 60317-0-1:2013 applies. 7 Springiness Clause 7 of IEC 60317-0-1:2013 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-1:2013 applies. The constant K used for the calculation of the number of revolutions for the peel test shall be 150 mm.
38、9 Heat shock Clause 9 of IEC 60317-0-1:2013 applies. The minimum heat shock temperature shall be 155 C. 10 Cut-through No failure shall occur within 2 min at 170 C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,000 mm) The wire shall meet the requirements
39、 given in Table 1. For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shall apply. BS IEC 60317-4:2015 8 IEC 60317-4:2015 IEC 2015 Table 1 Resistance to abrasion Nominal conductor diameter mm Grade 1 Grade 2 Minimum average force to failure N Minimu
40、m force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,250 0,280 0,315 0,355 0,400 0,450 0,500 0,560 0,630 0,710 0,800 0,900 1,000 1,120 1,250 1,400 1,600 1,800 2,000 2,30 2,50 2,70 2,90 3,15 3,40 3,65 3,90 4,20 4,50 4,80 5,20 5,6
41、0 6,00 6,50 7,00 7,50 8,00 8,60 1,95 2,10 2,30 2,50 2,70 2,90 3,10 3,30 3,55 3,80 4,10 4,40 4,75 5,15 5,55 5,95 6,35 6,80 7,30 4,10 4,40 4,75 5,10 5,45 5,80 6,20 6,65 7,10 7,60 8,10 8,70 9,30 10,0 10,7 11,4 12,2 13,1 14,0 3,50 3,70 4,00 4,30 4,60 4,90 5,25 5,60 6,00 6,45 6,90 7,40 7,90 8,50 9,10 9,7
42、0 10,4 11,1 11,9 12 Resistance to solvents Clause 12 of IEC 60317-0-1:2013 applies. 13 Breakdown voltage Clause 13 of IEC 60317-0-1:2013 applies. The elevated temperature shall be 130 C. 14 Continuity of insulation Clause 14 of IEC 60317-0-1:2013 applies. 15 Temperature index Clause 15 of IEC 60317-
43、0-1:2013 applies. The minimum temperature index shall be 130. 16 Resistance to refrigerants Test inappropriate. 17 Solderability 17.1 Nominal conductor diameters up to and including 0,100 mm The temperature of the solder bath shall be (375 5) C. The maximum immersion time shall be 2 s. BS IEC 60317-
44、4:2015IEC 60317-4:2015 IEC 2015 9 The surface of the tinned wire shall be smooth and free from holes and enamel residues. 17.2 Nominal conductor diameter over 0,100 mm The temperature of the solder bath shall be (375 5) C. The maximum immersion time (in seconds) shall be the following multiple of th
45、e nominal conductor diameter (in millimetres) with a minimum of 2 s. Grade 1 Grade 2 8 s/mm 12 s/mm The surface of the tinned wire shall be smooth and free from holes and enamel residues. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dissipation factor Test to be agreed between purcha
46、ser and supplier. The dielectric loss tangent at approximately 1 MHz shall not exceed 300 10-4if the wire is to be used in high-frequency coils. Compliance shall be checked by a method agreed between purchaser and supplier. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test in
47、appropriate. 23 Pin hole test Clause 23 of IEC 60317-0-1:2013 applies. 30 Packaging Clause 30 of IEC 60317-0-1:2013 applies. BS IEC 60317-4:2015 10 IEC 60317-4:2015 IEC 2015 Bibliography IEC 60264 (all parts), Packaging of winding wires IEC 60317 (all parts), Specifications for particular types of w
48、inding wires IEC 60851 (all parts), Winding wires Test methods _ BS IEC 60317-4:2015This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British S
49、tandards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and ref
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1