1、BSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 1-101: Blank detail specificationBS IEC 60512-1-101:2015National forewordThis British Standard is the UK implementation of IEC 60512-1-101:2015.The UK participation in its preparation was entrusted to TechnicalCo
2、mmittee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsib
3、le for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 78881 9ICS 31.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Pol
4、icy and Strategy Committee on 31 May 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 60512-1-101:2015IEC 60512-1-101 Edition 1.0 2015-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Tests and measurements Part 1-101: Blan
5、k detail specification Connecteurs pour quipements lectroniques Essais et mesures Partie 1-101: Spcification particulire cadre INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 31.220.10 ISBN 978-2-8322-2630-8 Registered trademark of the International Electrote
6、chnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 60512-1-101:2015 IEC 2015 CONT
7、ENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope and object . 6 2 Normative references 6 3 Terms and definitions 6 4 Preparations 6 4.1 Test equipment . 6 4.2 Preparation of specimen . 6 4.3 Mounting of specimen . 8 5 Test / measuring method . 8 5.1 Pre-conditioning 8 5.2 Initial measurements . 8 5.3 Test
8、s 8 5.4 Recovery 8 5.5 Final measurements 8 6 Details to be specified . 10 Table 1 Preferred parameters 9 BS IEC 60512-1-101:2015IEC 60512-1-101:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 1-101: Blank detail specificati
9、on FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in
10、the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entruste
11、d to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Internatio
12、nal Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each
13、technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
14、Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their
15、 national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessmen
16、t services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees
17、, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the pub
18、lication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possi
19、bility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60512-1-101 has been prepared by subcommittee 48B: Electrical connectors, of IEC technical committ
20、ee 48: Electrical connectors and mechanical structures for electrical and electronic equipment. The text of this standard is based on the following documents: FDIS Report on voting 48B/2421/FDIS 48B/2433/RVD Full information on the voting for the approval of this standard can be found in the report
21、on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. BS IEC 60512-1-101:2015 4 IEC 60512-1-101:2015 IEC 2015 A list of all parts in the IEC 60512 series, published under the general title Connectors for electronic equipment Test
22、s and measurements, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publicatio
23、n will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS IEC 60512-1-101:2015IEC 60512-1-101:2015 IEC 2015 5 INTRODUCTION This blank detail (tests and measurements) specification is a supplementary document to the IEC 60512 test and measurements specification series and contai
24、ns requirements for style, layout and content of test and measurements specifications for connectors. The content of this blank detail (tests and measurements) specification is laid out in two parts: one page contains the example of the blank detail tests and measurements specification, on the adjac
25、ent page, the guidance notes refer to the example. The guidance notes have the same numbering as the relevant clauses of the example pages. The example pages may be used as a template when preparing a detail (tests and measurements) specification within the scope of this standard. This standard is n
26、ot intended to replace the templates and guidance notes of the IEC, but to assist in their application within the range of the IEC 60512 series standards. All users are reminded to adhere to the relevant directives and guidelines of the IEC when preparing a standard. This blank detail (tests and mea
27、surements) specification provides guidance and several common references and examples, but it is not possible to anticipate on all future standards. In new cases, it may be necessary to deviate from the document structure, e.g. by adding paragraphs, subclauses or other details. As there are also pub
28、lications providing test sequences including sets of test and measurement methods in the IEC 60512 series, attention is drawn not to apply this standard to this kind of publication as a whole, but to each of its constituting test methods. BS IEC 60512-1-101:2015 6 IEC 60512-1-101:2015 IEC 2015 CONNE
29、CTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 1-101: Blank detail specification Guidance notes 1 Scope and object This clause gives a general description of the purpose of the test, and of the measurement or conditioning, possibly with reference to conditions which may occur in actual u
30、se. 2 Normative references It may be necessary to refer to IEC 60512-1 (General). In addition, IEC 60512-X-X (Connectors for electronic equipment Tests and measurements), IEC 60068-2-XX (Environmental testing) and other specific documents may be referred, for instance to refer to a measuring method.
31、 If reference is made to a particular element, such as a clause, table, figure, etc., the referenced document shall be dated. 3 Terms and definitions In addition to the terminology used in, and applicable to, the detail (product) specification, as stated in 1.3 of IEC 60512-1, it is recommended that
32、 those terms and definitions which are unique to the test specified in the detail (product) specification be listed here. 4 Preparations 4.1 Test equipment Details of equipment, fixtures, gauges, etc. relating to the test are described here. 4.2 Preparation of specimen Details such as connector type
33、 (male, female, pair, etc.), contact type (male, female, pair, etc.), termination (wired or not), accessories (with or without) and any other details are described here. BS IEC 60512-1-101:2015IEC 60512-1-101:2015 IEC 2015 7 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 1-101: Blan
34、k detail specification 1 Scope and object This part of IEC 60512 is applicable to connectors or similar devices within the scope of IEC technical committee 48 where specified as such by the detail (product) specification. The object of this part is to detail a standard test method to determine the a
35、bility of a connector to withstand “XXX” when exposed to “XXX” conditions. This “XXX” test simulates “XXX” stresses which may be produced by “XXX”. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicati
36、on. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1:20XX, Connectors for electronic equipment Tests and measurements Part 1: General IEC 60512-X-X:20XX, Connectors for electron
37、ic equipment Tests and measurements Part X-X: XXXX test Xx:XXXX IEC 60068-2-XX:20XX, Environmental testing Part X XX -Tests Test Xx: XXXX 3 Terms and definitions For the purposes of this document, terms and definitions in 1.3 of IEC 60512-1 as well as the following apply. 3.1 XXXX 3.2 XXXX 4 Prepara
38、tions 4.1 Test equipment The following test equipment shall be provided to carry out this test. a) XXXX b) XXXX 4.2 Preparation of specimen The specimen consists of XXXX as specified in the detail (product) specification. Unless otherwise specified, the specimen shall be tested in the as-received co
39、ndition. BS IEC 60512-1-101:2015 8 IEC 60512-1-101:2015 IEC 2015 Guidance notes 4.3 Mounting of specimen The mounting method, as well as adaptors and/or alignment are described in this subclause. Figures may detail the fixation and/or the position/orientation of the test specimen, and the point of a
40、pplication of the stress or impact. 5 Test / measuring method 5.1 Pre-conditioning The detail (tests and measurements) specification states the parameters of the pre-conditioning. Unless otherwise specified, pre-conditioning shall be carried out under standard atmospheric conditions as specified in
41、IEC 60512-1. 5.2 Initial measurements The detail (tests and measurements) specification states the measurements and examinations which have to be performed prior to the test. 5.3 Tests The detail (tests and measurements) specification shall refer to the test in IEC 60068-1 or other test specificatio
42、n and/or state the test procedure. It may include duration, temperature and humidity, but also mechanical handling or physical or electrical load, and/or any other circumstances that are important for carrying out the test. If a set of preferred test conditions are available, the parameters may be d
43、efined in a table. 5.4 Recovery The detail (tests and measurements) specification shall state the recovery time and the standard number to be referred. 5.5 Final measurements The detail (tests and measurements) specification shall state the same measurements as 5.2. Intermediate measuring moments, i
44、f any, may also be defined. Further, specific precautions and safety warnings can be mentioned in this clause or its subclauses. BS IEC 60512-1-101:2015IEC 60512-1-101:2015 IEC 2015 9 4.3 Mounting of specimen The specimen shall be mounted XXXX as indicated in the detail (product) specification. 5 Te
45、st / measuring method 5.1 Pre-conditioning Before starting the initial measurements, the specimens shall be preconditioned under standard atmospheric conditions for testing as specified in IEC 60512-1 for a period of 24 h, unless otherwise specified in the detail (product) specification. 5.2 Initial
46、 measurements Before test is started, XXXX shall be done in accordance with IEC 60512-X-X. 5.3 Tests The test shall be carried out in accordance with IEC 60068-2-XX with one of the following preferred parameters (see Table 1), unless otherwise specified in the detail (product) specification. The pos
47、ition of the specimen and the point of application of the stress shall be as indicated in Figure X. Table 1 Preferred parameters Preferred test conditions Tolerances (units) (units) XX x YY y ZZ z UU u Preferred duration of application: XX s x s. 5.4 Recovery After removal from the test, the specime
48、n shall be allowed to recover for X min under standard atmospheric conditions according to Clause 2 of IEC 60512-1. 5.5 Final measurements After removal of the samples from the test condition or during intermediate measurements (if any), the samples shall be verified for failures by means of general
49、 inspection and/or specific tests or measurements. In addition, the measurements as described under 5.2 are repeated. BS IEC 60512-1-101:2015 10 IEC 60512-1-101:2015 IEC 2015 Guidance notes 6 Details to be specified The test and measurement method document may specify details which are not applicable for certain products, or there may be details for a certain product which are not covered by the test method document. Such deviations and other matters th
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1