BS IEC 61196-4-1-2016 Coaxial communication cables Blank detail specification for radiating cables《同轴通信电缆 散热电缆的空白详细规格》.pdf

1、BSI Standards PublicationCoaxial communication cablesPart 4-1: Blank detail specification for radiating cablesBS IEC 61196-4-1:2016National forewordThis British Standard is the UK implementation of IEC 61196-4-1:2016. The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46

2、, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users a

3、re responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85600 6ICS 33.120.10 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the

4、Standards Policy and Strategy Committee on 31 January 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 61196-4-1:2016IEC 61196-4-1 Edition 1.0 2016-01 INTERNATIONAL STANDARD Coaxial communication cables Part 4-1: Blank detail specification for radiating cab

5、les INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.10 ISBN 978-2-8322-3092-3 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. BS IEC 61196-4-1:2016 2 IEC 61196-4-1:2016 IEC 2016 CONTENTS

6、FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Guidance for the preparation of detail specifications 5 4 Blank detail specification . 6 BS IEC 61196-4-1:2016IEC 61196-4-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COAXIAL COMMUNICATION CABLES Part 4-1: Blank detail specification

7、for radiating cables FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning s

8、tandardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their prepa

9、ration is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely w

10、ith the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant su

11、bjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technic

12、al content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent

13、 possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide co

14、nformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its di

15、rectors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses aris

16、ing out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is

17、drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61196-4-1 has been prepared by subcommittee 46A: Coaxial cables, of IEC technica

18、l committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46A/1279/FDIS 46A/1290/RVD Full information on the voting for the approval of this standard can be f

19、ound in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. It is intended to be read in conjunction with IEC 61196-1:2005 and IEC 61196-4:2015. BS IEC 61196-4-1:2016 4 IEC 61196-4-1:2016 IEC 2016 A list of all parts

20、 of the IEC 61196 series, under the general title: Coaxial communication cables, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data rela

21、ted to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. BS IEC 61196-4-1:2016IEC 61196-4-1:2016 IEC 2016 5 COAXIAL COMMUNICATION CABLES Part 4-1: B

22、lank detail specification for radiating cables 1 Scope This part of IEC 61196, which is a blank detail specification, applies to radiating coaxial communication cables. These cables are intended for use in wireless communication system, such as tunnels, railways, highways, subways, elevators and oth

23、er installations in which conventional radio transmission is not satisfactory or even impossible. It determines the layout and style for detail specification. Detail specifications, based on the blank detail specification, may be prepared by a national organization a manufacturer, or a user. 2 Norma

24、tive references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

25、applies. IEC 61196-1:2005, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-4:2015, Coaxial communication cables Part 4: Sectional specification for radiating cables 3 Guidance for the preparation of detail specifications The detail specifica

26、tion shall be written in accordance with the layout of the blank detail specification, which forms part of this standard. When a characteristic does not apply, then na (for not applicable) should be entered in the appropriate space. When a characteristic applies but a specific value is not considere

27、d necessary, then ns (for not specified). The numbers shown in brackets in this and the following pages correspond to the following items of required information, which should be entered in the space provided. 1 Name and address of the organization that has prepared the document 2 IEC document numbe

28、r and date of issue 3 Address of the organization from which the document is available 4 Related documents 5 Any other references to the cable, national reference, trade name, etc. 6 Complete description of the cable 7 Cable construction 8 Engineering information 9 Parameter or characteristic BS IEC

29、 61196-4-1:2016 6 IEC 61196-4-1:2016 IEC 2016 10 Reference to the relevant subclause of the sectional specification IEC 61196-4 11 Minimum requirements of the sectional specification IEC 61196-4 12 Remarks 4 Blank detail specification Title 1 Prepared by: 2 Document No.: Issue: Date: 3 Available fro

30、m: 4 Generic specification IEC 61196-1 Sectional specification IEC 61196-4 5 Additional references: 6 Cable description: a) Cable variant b) Material of inner conductor c) Material of dielectric d) Outer conductor e) Material of sheath (if any) 7 Cable construction a) Inner conductor Material Diamet

31、er (mm) nominal Tolerance (mm): b) Dielectric Material Diameter (mm) nominal Tolerance (mm): c) Outer conductor Material Diameter (mm) nominal Tolerance (mm): . d) Sheath (if any) Material Minimum thickness (mm) Diameter (mm) Tolerance (mm): 8 Engineering information (reference only) a) Operating te

32、mperature range b) Operating frequency c) Nominal characteristic impedance d) Maximum continue working voltage e) Minimum bending radius (static state) f) Minimum bending radius (dynamic state) g) Nominal weight h) Power rating i) Cut-off frequency BS IEC 61196-4-1:2016IEC 61196-4-1:2016 IEC 2016 7

33、9 Parameter or characteristic 10 IEC 61196-4:2015 Subclause 11 Value 12 Remarks Electrical characteristics 7.1 Continuity 7.2.1 Inner and outer conductor direct current resistance 7.2.2 Inner conductor /km 20 C Outer conductor /km 20 C Capacitance 7.2.3 Frequency: pF/m Withstand voltage of dielectri

34、c 7.2.4 kV rms or DC 40 Hz 60 Hz Withstand voltage of sheath (or spark voltage) a7.2.5 kV rms 40 Hz 60 Hz Insulation resistance 7.2.6 M km 5 000 Mkm according to IEC 61196-4 Mean characteristic impedance 7.2.7 ( ) 200 MHz Return loss 7.2.8 at MHz dB Attenuation constant 7.2.9 at MHz dB/100 m 20 C If

35、 necessary, refer to a table or graph at the end of the detail specification Coupling loss 7.2.10 c50 dB MHz c95 dB . MHz If necessary, refer to a table or graph at the end of the detail specification Environmental characteristics 7.3 Ageing 7.3.1 Value in accordance with the detail specification Co

36、ld bend performance 7.3.2 Value in accordance with the detail specification Climatic sequence method 1 7.3.3 Value in accordance with the detail specification Environmental stress cracking 7.3.4 Value in accordance with the detail specification Mechanical characteristics 7.4 Visual examination 7.4.1

37、 Pass Dimensional examination 7.4.2 Value in accordance with the detail specification Ovality of inner conductor 7.4.3 % Ovality of outer conductor 7.4.4 % Ovality of dielectric 7.4.5 % Eccentricity of dielectric 7.4.6 % Eccentricity of sheath 7.4.7 % BS IEC 61196-4-1:2016 8 IEC 61196-4-1:2016 IEC 2

38、016 9 Parameter or characteristic 10 IEC 61196-4:2015 Subclause 11 Value 12 Remarks Cable bending under tension 7.4.8 1) length of the cable: 2) length bent under tension: 3) radius, R, of rollers / cylinders / mandrels: 4) distance, Y: 5) bending angle, : 6) moving speed: 7) tensile load: Crush res

39、istance of cable 7.4.9 Load: N Impedance irregularity: 1 % Fire performance requirement 7.5 In accordance with the requirements of national or regional authorities, when required Flame propagation 7.5.1 In accordance with the requirements of national or regional authorities, when required Halogen ac

40、id gas emission 7.5.2 In accordance with the requirements of national or regional authorities, when required Toxic gas emission 7.5.3 In accordance with the requirements of national or regional authorities, when required Smoke density 7.5.4 In accordance with the requirements of national or regional

41、 authorities, when required a Mark na, if not applicable. _ BS IEC 61196-4-1:2016This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Stan

42、dards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experienc

43、e and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Informati

44、on on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, incl

45、uding British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur

46、 range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its av

47、ailable 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service ex

48、clusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email bsmusales