BS IEC 62946-02-2017 Connectors for electronic equipment Detail specification for 8-way unshielded free and fixed high density connectors for data transmission with frequencies up .pdf

1、Connectors for electronic equipmentPart 02: Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with current carrying capacity up to 1 ABS IEC 62946-02:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_A

2、W.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of IEC 62946-02:2017. The UK participation in its preparation was entrusted to TechnicalCommittee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations r

3、epresented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0

4、580 89395 7ICS 31.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH ST

5、ANDARDBS IEC 62946-02:2017IEC 62946-02 Edition 1.0 2017-01 INTERNATIONAL STANDARD Connectors for electronic equipment Part 02: Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with current carrying capacity up

6、 to 1 A INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 31.220.10 ISBN 978-2-8322-3838-7 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colourinsideBS IEC 62946-02:2017 2 IEC 62946-02:2017 IEC

7、2017 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 8 2 Normative references 8 3 Terms and definitions 8 4 Common features and typical connector pair . 9 4.1 Mating information 9 4.1.1 General . 9 4.1.2 Contacts mating conditions . 9 4.1.3 Fixed connector . 10 4.1.4 Free connector 12 5 Characteristi

8、cs 13 5.1 General . 13 5.2 Pin and pair grouping assignment . 13 5.3 Classification into climatic category 13 5.4 Electrical characteristics . 13 5.4.1 General . 13 5.4.2 Creepage and clearance distances 13 5.4.3 Contact resistance . 14 5.4.4 Voltage proof . 14 5.4.5 Current-temperature derating . 1

9、4 5.4.6 Initial insulation resistance 15 5.4.7 Input to output d.c. resistance 15 5.4.8 Input to output d.c. resistance unbalance . 15 5.4.9 Transfer impedance . 16 5.5 Transmission characteristics . 16 5.5.1 General . 16 5.5.2 Insertion loss (IL) . 16 5.5.3 Return loss (RL) 16 5.5.4 Near end cross

10、talk (NEXT) . 16 5.5.5 Far end cross talk (FEXT) 16 5.5.6 Transverse conversion loss (TCL) . 17 5.5.7 Transverse conversion transfer loss (TCTL) 17 5.5.8 Propagation delay 17 5.5.9 Delay skew 17 5.6 Mechanical characteristics 17 5.6.1 Mechanical operation . 17 5.6.2 Insertion and withdrawal forces .

11、 17 6 Tests and test schedule . 17 6.1 General . 17 6.2 Arrangement for contact resistance measurement . 18 6.3 Arrangement for vibration test (test phase EP5), see Figure 8. 19 6.4 Test procedures and measuring methods 20 6.5 Preconditioning . 20 6.6 Test schedules 20 6.6.1 Basic (minimum) test sch

12、edule 20 BS IEC 62946-02:2017IEC 62946-02:2017 IEC 2017 3 6.6.2 Full test schedule 20 Figure 1 Contact interface dimensions with terminated free connector . 9 Figure 2 View of contact zone 10 Figure 3 View of contact zone section A-A . 11 Figure 4 Free connector view . 12 Figure 5 Fixed connector pi

13、n and pair grouping assignment (front view of connector) 13 Figure 6 Connector de-rating curve 15 Figure 7 Arrangement for contact resistance measurement 18 Figure 8 Arrangement for vibration test 19 Table 1 Climatic categories selected values 13 Table 2 Creepage and clearance distances 14 Table 3 T

14、est group P Preliminary 21 Table 4 Test group AP Mechanical endurance 22 Table 5 Test group BP Climatic . 23 Table 6 Test group CP Corrosion 24 Table 7 Test group DP Moisture 25 Table 8 Test group EP Dynamic stress 26 Table 9 Test group FP Latch and cable stress 27 Table 10 Test group GP Signal inte

15、grity 28 BS IEC 62946-02:2017 4 IEC 62946-02:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT Part 02: Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz a

16、nd with current carrying capacity up to 1 A FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all

17、 questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Public

18、ation(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC

19、 collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opi

20、nion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to

21、ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparentl

22、y to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certific

23、ation bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall

24、attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal

25、fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this public

26、ation. International Standard IEC 62946-02 has been prepared by subcommittee 48B: Electrical connectors, of IEC technical committee 48: Electrical connectors and mechanical structures for electrical and electronic equipment. The text of this International Standard is based on the following documents

27、: FDIS Report on voting 48B/2537/FDIS 48B/2546/RVD Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts i

28、n the IEC 62946 series, under the general title Connectors for electronic equipment, can be found on the IEC website. BS IEC 62946-02:2017IEC 62946-02:2017 IEC 2017 5 The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC webs

29、ite under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover p

30、age of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS IEC 62946-02:2017 6 IEC 62946-02:2017 IEC 2017 INTRODUCTION The International Electrotechn

31、ical Commission (IEC) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent concerning connectors given in this specification. The IEC takes no position concerning the evidence, validity and scope of this patent right. The holder of this pa

32、tent right has assured the IEC that he is willing to give free licences with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with the IEC. Information may be obtained from: TE Connectivity Ltd., Shanghai HQ, No 1528 Gumei Road, Caoheji

33、ng, 200233, Shanghai, China. Telephone +86-21-33980276. Email: Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights other than those identified above. IEC shall not be held responsible for identifying any or all such pate

34、nt rights. ISO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line data bases of patents relevant to their standards. Users are encouraged to consult the data bases for the most up to date information concerning patents. BS IEC 62946-02:2017IEC 62946-02:2017 IEC 2017 7 IEC 62946-02

35、, Ed. 1 (date of issue) Subcommittee 48B: Electrical connectors 8-way, unshielded, free and fixed high density connectors for data transmission up to 250 MHz and with current carrying capacity up to 1 A. Fixed connectors are mounted on printed circuit board, the free connector is attached to wires.

36、IEC BS IEC 62946-02:2017 8 IEC 62946-02:2017 IEC 2017 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT Part 02: Detail specification for 8-way, unshielded, free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with current carrying capacity up to 1 A 1 Sco

37、pe This part of IEC 62946 covers 8-way, unshielded free and fixed high density connectors for data transmission with frequencies up to 250 MHz and with extra low voltage current carrying capabilities up to 1 A, and is intended to specify the common dimensions, mechanical, electrical, signal integrit

38、y and environmental characteristics and tests for these connectors. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated

39、references, the latest edition of the referenced document (including any amendments) applies. IEC 60050-581, International Electrotechnical Vocabulary (IEV) Chapter 581: Electromechanical components for electronic equipment IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60512 (a

40、ll parts), Connectors for electronic equipment Tests and measurements IEC 60512-1, Connectors for electronic equipment Tests and measurements Part 1: General IEC 60512-1-100, Connectors for electronic equipment Tests and measurements Part 1-100: General Applicable publications IEC 60512-11-7, Connec

41、tors for electronic equipment Tests and measurements Part 11-7: Climatic tests Test 11g: Flowing mixed gas corrosion test IEC 60512-26-100, Connectors for electronic equipment Tests and measurements Part 26-100: Measurement setup, test and reference arrangements and measurements for connectors accor

42、ding to IEC 60603-7 Tests 26a to 26g IEC 61984, Connectors Safety requirements and tests ISO/IEC 11801, Information technology Generic cabling for customer premises 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60050-581, IEC 60512-1 and the follow

43、ing apply. BS IEC 62946-02:2017IEC 62946-02:2017 IEC 2017 9 ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 3.1 interoperab

44、ility interoperability of connectors to this standard from different sources is ensured by compliance with the specified interface dimensions 4 Common features and typical connector pair 4.1 Mating information 4.1.1 General Dimensions are given in millimetres. Drawings are shown in third-angle proje

45、ction. The shape of connectors may deviate from those given in Figures 1 to 4 and Tables 1 to 3 as long as the dimensions specified are not changed. 4.1.2 Contacts mating conditions Letter Minimum Nominal (ref.) Maximum mm mm A1 2,00 2,50 A2 1,82 1,98 B2 30 P1 0,19 0,21 P2 0,38 0,51 Key 1 Female con

46、tact of fixed connector. The mating information shown can only be achieved when a free connector is mated with a fixed connector, see the cross-section on the right, taken at the center of two opposite contacts. 2 Burrs shall not project above the top of the contact in this area, since it may be a c

47、ontact area. Figure 1 Contact interface dimensions with terminated free connector IEC BS IEC 62946-02:2017 10 IEC 62946-02:2017 IEC 2017 4.1.3 Fixed connector Letter Minimum Nominal (ref.) Maximum mm mm or mm B1 3,75 3,85 C1 2,72 2,78 D1 1,72 1,78 E1 1,25 1,35 F1 4,55 4,61 G1 5,77 5,83 H1 7,45 7,50

48、J1 1 K1 1,45 1,55 L1 2,00 2,10 M1 3,35 3,45 Q1 5,85 5,95 Key 1 Contact zone. Contacts shall be completely within their individual contact zone in the area indicated. 2 Section A-A: see Figure 3. Figure 2 View of contact zone IEC BS IEC 62946-02:2017IEC 62946-02:2017 IEC 2017 11 Letter Minimum Nomina

49、l (ref.) Maximum mm mm or mm S1 8,75 8,85 T1 8,50 8,60 W1 6,95 7,05 AB1 0,25 45 AC1 1,62 1,78 AD1 1,13 AE1 6,25 6,35 AF1 3,95 4,05 AH1 7,01 7,11 AM1 4,95 5,05 Key 1 Preferred free connector stop. 2 This surface needs not be planar or coincident with the surface below the locking device as long as insertion, latching and unlatching of free connectors is not inhibited. 3