BS ISO 10071-1-2008 Tools for pressing - Ball-lock punches - Ball-lock punches for light duty《冲压工具 球锁紧的冲头 轻型球锁紧冲头》.pdf

1、BS ISO10071-1:2008ICS 25.120.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTools for pressing Ball-lock punchesPart 1: Ball-lock punches for light dutyThis British Standardwas published under the authority of theStandards Policy andStrategy Committee on 3200

2、8 BSI 2008ISBN 978 0 580 64303 3Amendments/corrigenda issued since publicationDate CommentsBS ISO 10071-1:2008National forewordThis British Standard is the UK implementation of ISO 10071-1:2008. Itsupersedes BS ISO 10071-1:2001 which is withdrawn.The UK participation in its preparation was entrusted

3、 to TechnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Co

4、mpliance with a British Standard cannot confer immunityfrom legal obligations.December1BS ISO 10071-1:2008Reference numberISO 10071-1:2008(E)ISO 2008INTERNATIONAL STANDARD ISO10071-1Second edition2008-11-15Tools for pressing Ball-lock punches Part 1: Ball-lock punches for light duty Outillage de pre

5、sse Poinons bille Partie 1: Poinons bille pour tles minces BS ISO 10071-1:2008ISO 10071-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedde

6、d are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. De

7、tails of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem

8、 relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includin

9、g photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published

10、in Switzerland ii ISO 2008 All rights reservedBS ISO 10071-1:2008ISO 10071-1:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Terms and definitions .1 4 Dimensions.1 4.1 Basic dimensions Ball in locking position .1 4.2 Perforating punches3 4.3 Pi

11、lot punches .6 4.4 Punches with ejector.8 5 Material and hardness.11 6 Designation 11 Bibliography 12 BS ISO 10071-1:2008ISO 10071-1:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me

12、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme

13、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Dire

14、ctives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bod

15、ies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10071-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommit

16、tee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (ISO 10071-1:2001), of which it constitutes a minor revision. In particular, the normative references given in Clause 2 have been updated, and the indication of surface textures has been made in acc

17、ordance with ISO 1302:2002. ISO 10071 consists of the following parts, under the general title Tools for pressing Ball-lock punches: Part 1: Ball-lock punches for light duty Part 2: Ball-lock punches for heavy duty BS ISO 10071-1:2008INTERNATIONAL STANDARD ISO 10071-1:2008(E) ISO 2008 All rights res

18、erved 1Tools for pressing Ball-lock punches Part 1: Ball-lock punches for light duty 1 Scope This part of ISO 10071 specifies interchangeability dimensions and tolerances, in millimetres, for ball-lock punches for light duty. It is applicable to ball-lock punches with shank diameter sizes from 6 mm

19、up to and including 32 mm, in round, square, rectangular and oblong shapes, for punching holes in steel sheets or other materials, the thickness of which is less than 3 mm. This part of ISO 10071 also gives examples related to materials and hardness, and specifies the designation of ball-lock punche

20、s for light duty. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768

21、-1:1989, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 8695, Tools for pressing Punches Nomenclature and terminology 3 Terms and definitions For the purposes of this part of ISO 10071, the terms and definitions given in ISO 8695

22、apply. 4 Dimensions 4.1 Basic dimensions Ball in locking position The dimension of the ball and the dimensions and tolerances of the ball seat of ball-lock punches for light duty shall conform to the indications given in Figure 1 and Table 1. BS ISO 10071-1:2008ISO 10071-1:2008(E) 2 ISO 2008 All rig

23、hts reservedGeneral tolerance: ISO 2768-m aBall seat relief: type and dimensions at manufacturers direction. bAlternative ball seat relief types (band type, swipe type). cBall seat. dTwo-point contact. Figure 1 Table 1 D1g5 Ball diameter d e ,020+f ,0016 6 14 5,2 10 8 12,4 6,7 13 8 12,4 6,7 16 8 12,

24、4 6,7 20 8 12,4 6,7 25 8 12,4 6,7 32 8 12,4 6,7 BS ISO 10071-1:2008ISO 10071-1:2008(E) ISO 2008 All rights reserved 34.2 Perforating punches 4.2.1 Punches with straight shank Type A The dimensions of type A ball-lock punches with a straight shank shall conform to the indications given in Figure 2 an

25、d Table 2. General tolerance: ISO 2768-m Surface roughness value in micrometres Figure 2 Table 2 l ,050+D1g5 63 71 80 90 100 6 10 13 16 20 25 32 NOTE See 4.1 for the dimension of the ball and dimensions and tolerances of the ball seat. BS ISO 10071-1:2008ISO 10071-1:2008(E) 4 ISO 2008 All rights res

26、erved4.2.2 Punches with reduced shank 4.2.2.1 Punches with round shape Type B The dimensions of type B ball-lock punches with a round shape shall conform to the indications given in Figure 3 and Table 3. General tolerance: ISO 2768-m Surface roughness value in micrometres Figure 3 Table 3 l ,050+D1g

27、5 D3 0,01 63 71 80 90 100 6 1,6 u D3u 5,9 10 3,5 u D3u 9,9 13 6 u D3u 12,9 16 8,5 u D3u 15,9 20 12,5 u D3u 19,9 25 18 u D3u 24,9 32 20 u D3u 31,9 NOTE The point length, l1, is left to the manufacturers direction. See 4.1 for the dimension of the ball and dimensions and tolerances of the ball seat. B

28、S ISO 10071-1:2008ISO 10071-1:2008(E) ISO 2008 All rights reserved 54.2.2.2 Punches with square (S), rectangular (R) and oblong (O) shapes Types BS, BR and BO The dimensions of types BS, BR and BO ball-lock punches with a square, rectangular and oblong shape shall conform to the indications given in

29、 Figure 4 and Table 4. General tolerance: ISO 2768-m Surface roughness value in micrometres aStandard at 90. bOn all work faces of the point. Figure 4 Table 4 D1g5 Type BS a 0,01 Types BR and BO a and b 0,01 l ,050+6 1,6 u a u 4,2 1,6 u a and b u 5,9 63 71 80 90 100 10 3,2 u a u 7 3,2 u a and b u 9,

30、9 13 5 u a u 9,1 5 u a and b u 12,9 16 6,5 u a u 11,2 6,3 u a and b u 15,9 20 8,5 u a u 14,1 8 u a and b u 19,9 25 11 u a u 17,6 10 u a and b u 24,9 32 14 u a u 22,5 12 u a and b u 31,9 NOTE The point length, l1, is left to the manufacturers discretion. See 4.1 for the dimension of the ball and dime

31、nsions and tolerances of the ball seat. BS ISO 10071-1:2008ISO 10071-1:2008(E) 6 ISO 2008 All rights reserved4.3 Pilot punches 4.3.1 Pilot punches Type C The dimensions of type C ball-lock pilot punches shall conform to the indications given in Figure 5 and Table 5. General tolerance: ISO 2768-m Sur

32、face roughness value in micrometres aThe diameter D3of the pilot shall be smaller than the diameter of the equivalent punch. Figure 5 Table 5 l ,050+D1g5 D3 0,01 63 71 80 90 100 6 1,59 u D3u 5,9 10 3,49 u D3u 9,9 13 5,99 u D3u 12,9 16 8,49 u D3u 15,9 20 12,49 u D3u 19,9 25 17,99 u D3u 24,9 32 19,99

33、u D3u 31,9 NOTE The point lengths, l1and l3, and the point shape are left to the manufacturers discretion. See 4.1 for the dimension of the ball and dimensions and tolerances of the ball seat. BS ISO 10071-1:2008ISO 10071-1:2008(E) ISO 2008 All rights reserved 74.3.2 Positive pilot punches Type D Th

34、e dimensions of type D ball-lock pilot punches shall conform to the indications given in Figure 6 and Table 6. General tolerance: ISO 2768-m Surface roughness value in micrometres aThe diameter D3of the pilot shall be smaller than the diameter of the equivalent punch. Figure 6 Table 6 l ,050+D1g5 D3

35、 0,01 63 71 80 90 100 10 5 u D3u 9,9 13 9 u D3u 12,9 16 12 u D3u 15,9 20 15 u D3u 19,9 25 19 u D3u 24,9 32 24 u D3u 31,9 NOTE The point lengths, l1and l3, and the point shape are left to the manufacturers discretion. See 4.1 for the dimension of the ball and dimensions and tolerances of the ball sea

36、t. BS ISO 10071-1:2008ISO 10071-1:2008(E) 8 ISO 2008 All rights reserved4.4 Punches with ejector 4.4.1 Punches with ejector with straight shank Type E The dimensions of type E ball-lock punches that have an ejector with a straight shank shall conform to the indications given in Figure 7 and Table 7.

37、 General tolerance: ISO 2768-m Surface roughness value in micrometres Figure 7 Table 7 l ,050+D1g5 63 71 80 90 100 6 10 13 16 20 25 32 NOTE The ejector components and the locking hole are left to the manufacturers discretion. See 4.1 for the dimension of the ball and dimensions and tolerances of the

38、 ball seat. BS ISO 10071-1:2008ISO 10071-1:2008(E) ISO 2008 All rights reserved 94.4.2 Punches with ejector with reduced shank 4.4.2.1 Punches with ejector with round shape Type F The dimensions of type F ball-lock punches that have an ejector with a round shape shall conform to the indications give

39、n in Figure 8 and Table 8. General tolerance: ISO 2768-m Surface roughness value in micrometres Figure 8 Table 8 l ,050+D1g5 D3 0,01 63 71 80 90 100 6 1,6 u D3u 5,9 10 3,5 u D3u 9,9 13 6 u D3u 12,9 16 8,5 u D3u 15,9 20 12,5 u D3u 19,9 25 18 u D3u 24,9 32 20 u D3u 31,9 NOTE The point length, l1, the

40、ejector components and the locking hole are left to the manufacturers discretion. See 4.1 for the dimension of the ball and dimensions and tolerances of the ball seat. BS ISO 10071-1:2008ISO 10071-1:2008(E) 10 ISO 2008 All rights reserved4.4.2.2 Punches with ejector with square (S), rectangular (R)

41、and oblong (O) shapes Type FS, FR and FO The dimensions of types FS, FR and FO ball-lock punches with ejector and square, rectangular or oblong shape shall conform to the indications given in Figure 9 and Table 9. General tolerance: ISO 2768-m Surface roughness value in micrometres aStandard at 90.

42、bOn all work faces of the point. Figure 9 Table 9 D1g5 Type FS a 0,01 Types FR and FO a and b 0,01 l ,050+6 1,6 u a u 4,2 1,6 u a and b u 5,9 63 71 80 90 100 10 3,2 u a u 7 3,2 u a and b u 9,9 13 5 u a u 9,1 5 u a and b u 12,9 16 6,5 u a u 11,2 6,3 u a and b u 15,9 20 8,5 u a u 14,1 8 u a and b u 19

43、,9 25 11 u a u 17,6 10 u a and b u 24,9 32 14 u a u 22,5 12 u a and b u 31,9 NOTE The point length, l1, the ejector components and the locking hole are left to the manufacturers discretion. See 4.1 for the dimension of the ball and dimensions and tolerances of the ball seat. BS ISO 10071-1:2008ISO 1

44、0071-1:2008(E) ISO 2008 All rights reserved 115 Material and hardness The material is left to the manufacturers discretion. The following hardness values are given as examples: a) alloyed cold work steel with 5 % to 12 % Cr: (60 2) HRC; b) high speed steel: (62 2) HRC. 6 Designation A ball-lock punc

45、h in accordance with this part of ISO 10071 shall be designated by: a) “Ball-lock punch”; b) reference to this part of ISO 10071, i.e. ISO 10071-1; c) type of punch (A, B, BS, BR, BO, C, D, E, F, FS, FR or FO); d) its shank diameter, D1, in millimetres; e) for types B, BS, BR, BO, C, D, F, FS, FR an

46、d FO, its point dimensions (D3, a or a b), in millimetres; f) for types BS, BR, BO, FS, FR and FO, the relative position of the shape to the ball seat position (0 or 90); g) its overall length, l, in millimetres; h) its material (alloyed cold work steel with 5 % to 12 % Cr or high-speed steel). EXAM

47、PLE 1 A ball-lock punch, round (type B), diameter D1= 6 mm, range of point diameter D3= 2 mm and overall length l = 63 mm in alloyed cold work steel, is designated as follows: Ball-lock punch ISO 10071-1 B 6 2 63 Alloyed cold work steel EXAMPLE 2 A ball-lock punch, rectangular (type BR), diameter D1= 6 mm, range of point size a b = 2 mm 3 mm with a ball seat position at 90 and overall length l = 63 mm in high-speed steel, is designated as follows: Ball-lock punch ISO 10071-1 BR 6 2 3 90 63 High-speed steel BS ISO 10071-1:2008ISO 10071-1:2008(E)