BS ISO 10242-1-2011 Tools for pressing Punch holder shanks Type A《压力工具 上夹板柄 A类型》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 10242-1:2011Tools for pressing Punchholder shanksPart 1: Type ABS ISO 10242-1:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 1

2、0242-1:2011.It supersedes BS ISO 10242-1:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does

3、not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 73924 8ICS 25.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of th

4、eStandards Policy and Strategy Committee on 30 September 2011.Amendments issued since publicationDate Text affectedBS ISO 10242-1:2011Reference numberISO 10242-1:2011(E)ISO 2011INTERNATIONAL STANDARD ISO10242-1Third edition2011-09-15Tools for pressing Punch holder shanks Part 1: Type A Outillage de

5、presse Nez de presse Partie 1: Type A BS ISO 10242-1:2011ISO 10242-1:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

6、and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland

7、ii ISO 2011 All rights reservedBS ISO 10242-1:2011ISO 10242-1:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normall

8、y carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the

9、work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare In

10、ternational Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of

11、 the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10242-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This third edition cancels

12、and replaces the second edition (ISO 10242-1:1998), of which it constitutes a minor revision. In particular, the indication of surface textures has been updated in accordance with ISO 1302:2002. ISO 10242 consists of the following parts, under the general title Tools for pressing Punch holder shanks

13、 Part 1: Type A Part 2: Type C Part 3: Type D BS ISO 10242-1:2011BS ISO 10242-1:2011INTERNATIONAL STANDARD ISO 10242-1:2011(E) ISO 2011 All rights reserved 1Tools for pressing Punch holder shanks Part 1: Type A 1 Scope This part of ISO 10242 specifies the interchangeability dimensions and tolerance

14、s, in millimetres, of punch holder shanks with neck and flats, type A, intended for use in press tools. It gives guidance on the materials, and specifies the hardness and designation of punch holder shanks in accordance with this part of ISO 10242. 2 Dimensions The dimensions of punch holder type A

15、shank shall be in accordance with the indications of Figure 1 and Table 1. BS ISO 10242-1:2011ISO 10242-1:2011(E) 2 ISO 2011 All rights reservedSurface roughness values in micrometres Figure 1 Punch holder shank type A BS ISO 10242-1:2011ISO 10242-1:2011(E) ISO 2011 All rights reserved 3Table 1 Dime

16、nsions of punch holder shank type A Dimensions in millimetres D1f9 D2D3 P 6g l1l2l3l4l5 1 r s 20 15 M16 1,5 40 2 12 58 4 2,5 17 25 20 M16 1,5 45 2,5 16 68 6 2,5 21 M20 1,5 32 25 M20 1,5 56 3 16 79 6 2,5 27 M24 1,5 40 32 M24 1,5 70 4 26 93 12 4 36 M27 2 M30 2 50 42 M30 2 80 5 26 108 12 4 41 3 Materia

17、l and corresponding hardness The material is left to the manufacturers discretion, but the hardness shall be at least 140 HB. 4 Designation A punch holder shank in accordance with this part of ISO 10242 shall be designated by: a) “Punch holder shank”; b) reference to this part of ISO 10242, i.e. ISO

18、 10242-1; c) its type; d) its body diameter, D1, in millimetres; e) its nominal thread diameter, D3. EXAMPLE A punch holder shank of type A, of body diameter D1= 20 mm and of nominal thread diameter D3= M16 is designated as follows: Punch holder shank ISO 10242-1 A-20 M16 BS ISO 10242-1:2011ISO 1024

19、2-1:2011(E) 4 ISO 2011 All rights reservedBibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 2 ISO 6506 (all parts), Metallic materials Brinell hardness test BS ISO 10242-1:2011BS ISO 10242-1:2011ISO 10242-1:2011(E)

20、 ICS 25.120.10 Price based on 4 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and a

21、t the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-d

22、ards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical

23、 com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996

24、 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20

25、 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national

26、 Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Su

27、bscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online acc

28、ess to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted unde

29、r the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of impleme

30、nting the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: