BS ISO 10263-3-2009 Earth-moving machinery - Operator enclosure environment - Pressurization test method《土方机械 操作室密封环境 增压试验方法》.pdf

1、BS ISO10263-3:2009ICS 53.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDEarth-movingmachinery Operatorenclosure environmentPart 3: Pressurization test methodThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on

2、 30 April2009 BSI 2009ISBN 978 0 580 57407 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 10263-3:2009National forewordThis British Standard is the UK implementation of ISO 10263-3:2009. Itsupersedes BS 6912 22.3:1996 which is withdrawn.The UK participation in its preparation was

3、 entrusted to TechnicalCommittee B/513/1, Earth moving machinery (International).A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its corr

4、ect application.Compliance with a British Standard cannot confer immunityfrom legal obligations.-BS ISO 10263-3:2009Reference numberISO 10263-3:2009(E)ISO 2009INTERNATIONAL STANDARD ISO10263-3Second edition2009-02-01Earth-moving machinery Operator enclosure environment Part 3: Pressurization test me

5、thod Engins de terrassement Environnement de lenceinte de loprateur Partie 3: Mthode dessai du systme de pressurisation BS ISO 10263-3:2009ISO 10263-3:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed b

6、ut shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this

7、 area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for u

8、se by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in

9、 any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22

10、 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 10263-3:2009ISO 10263-3:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (

11、ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, go

12、vernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IE

13、C Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the memb

14、er bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10263-3 was prepared by Technical Committee ISO/TC 127, Earth-moving ma

15、chinery, Subcommittee SC 2, Safety, ergonomics and general requirements. This second edition cancels and replaces the first edition (ISO 10263-3:1994), which has been technically revised. ISO 10263 consists of the following parts, under the general title Earth-moving machinery Operator enclosure env

16、ironment: Part 1: Terms and definitions Part 2: Air filter element test method Part 3: Pressurization test method Part 4: Heating, ventilating and air conditioning (HVAC) test method and performance Part 5: Windscreen defrosting system test method Part 6: Determination of effect of solar heating BS

17、ISO 10263-3:2009BS ISO 10263-3:2009INTERNATIONAL STANDARD ISO 10263-3:2009(E) ISO 2009 All rights reserved 1Earth-moving machinery Operator enclosure environment Part 3: Pressurization test method 1 Scope This part of ISO 10263 specifies a test method which will provide for uniform measurement of th

18、e maximum pressurization inside an operator enclosure of an earth-moving machine when equipped with a pressurization system. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For und

19、ated references, the latest edition of the referenced document (including any amendments) applies. ISO 10263-1, Earth-moving machinery Operator enclosure environment Part 1: Terms and definitions 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 10263-

20、1 and the following apply. 3.1 pressurization pressure differential between the static pressure inside and outside of the operator enclosure 3.2 pressurization system means used to pressurize the operator enclosure, including any components which influence the performance of the system 4 Test equipm

21、ent 4.1 Device to measure pressure with a measuring accuracy of 5 % of the observed values. 4.2 Voltmeter or other voltage measuring device to measure blower voltage, with a measuring accuracy of 2 %. 4.3 Thermometers or other temperature measuring devices, with a measuring accuracy of 0,5 C. 4.4 De

22、vice to measure barometric pressure, with a measuring accuracy of 2 % of the observed values. 4.5 Anemometer to measure wind speed, with a measuring accuracy within 0,5 m/s. BS ISO 10263-3:2009ISO 10263-3:2009(E) 2 ISO 2009 All rights reserved5 Test conditions 5.1 The pressurization system shall be

23、completely powered by the standard equipment on the test machine with the engine operating at rated speed when the engine or other components influence the environment within the operator enclosure. The voltage at blower motor terminals shall be no more than 15 % above the nominal rating of the syst

24、em (for example 13,8 V for a 12 V system). 5.2 All machine accessories pertinent to the operation of the enclosure, enclosure components and blowers shall be standard production parts or the equivalent, adjusted within the machine manufacturers specification limits. Clean air filters are recommended

25、 since the amount of particulate matter in the filters may affect the pressurization. 5.3 It is recommended that the test be conducted in a controlled inside environment to minimize the influence of wind speed on the vehicle pressurization. 5.4 If the vehicle must be tested in an outside environment

26、, the vehicle must be oriented such that the normal operating direction of the vehicle is facing into the wind, and the wind direction is not more than 30 off the vehicle centreline. Test data must not be recorded when the wind speed is greater than 5 m/s. 5.5 An operator may be present in the enclo

27、sure throughout the duration of the test. 5.6 Maximum wind speed passing the machine: 5 m/s. 6 Test procedure 6.1 Operate the pressurization system for a minimum of 15 min prior to obtaining data. The pressurization system shall be operated using maximum outside air, with maximum blower speed settin

28、g. No automatic pressurization controls shall be locked out. 6.2 To obtain uniform results, neither the air conditioning nor heating systems shall be transferring heat during the pressurization system tests. 6.3 Record, for information purposes only, the blower voltage, ambient dry bulb temperature,

29、 barometric pressure, wind speed, and wind direction in relation to the machine centreline. 6.4 Record enclosure pressure in pascals (Pa). 6.5 The pressure measuring device shall be positioned to avoid velocity head by keeping its reference and measuring points away from air streams. 7 Test report T

30、he obtained enclosure pressure (Pa) shall be included in the test report. An example of a suitable test report form is given in Annex A. BS ISO 10263-3:2009ISO 10263-3:2009(E) ISO 2009 All rights reserved 3Annex A (informative) Example of test report form for pressurization Test machine Type: . Mode

31、l: PIN (or serial number): . Pressurization test (ISO 10263-3:2008, Clause 6) Blower voltage (6.3): V Ambient dry bulb temperature (6.3): C Barometric pressure (6.3): . Pa Wind speed passing machine (6.3): .m/s Wind direction relative to the machine centreline (6.3): .deg () Enclosure pressure (6.4)

32、: . Pa Setting of adjustable controls: BS ISO 10263-3:2009ISO 10263-3:2009(E) ICS 53.100 Price based on 3 pages ISO 2009 All rights reserved BS ISO 10263-3:2009This page has been intentionally left blank BS ISO10263-3:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 89

33、96 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amend

34、ment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would i

35、nform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest edit

36、ions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ respons

37、e to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Li

38、brary and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with

39、 standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standard

40、sOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs

41、and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necess

42、ary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: