BS ISO 10474-2013 Steel and steel products Inspection documents《钢和钢制品 检验文件》.pdf

1、BSI Standards PublicationBS ISO 10474:2013Steel and steel products Inspection documentsBS ISO 10474:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10474:2013.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/100, Steel, Gener

2、al Issues.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BS

3、I StandardsLimited 2013ISBN 978 0 580 75096 0ICS 77.140.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationDate Text

4、 affectedBS ISO 10474:2013 ISO 2013Steel and steel products Inspection documentsAciers et produits sidrurgiques Documents de contrleINTERNATIONAL STANDARDISO10474Second edition2013-07-01Reference numberISO 10474:2013(E)BS ISO 10474:2013ISO 10474:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTEC

5、TED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permis

6、sion can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 10474:2013ISO 10474:2013

7、(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Inspection documents based on non-specific inspection 24.1 Declaration of compliance with the order “2.1” . 24.2 Test report “2.2” . 25 Inspection documents based on specific i

8、nspection . 25.1 Inspection certificate 3.1 25.2 Inspection certificate 3.2 26 Inspection documents supplied by an intermediary 37 Validation of inspection documents . 38 Summary of documents. 3Bibliography 4BS ISO 10474:2013ISO 10474:2013(E)ForewordISO (the International Organization for Standardiz

9、ation) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be

10、 represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to

11、 develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of th

12、e ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during th

13、e development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this docume

14、nt is ISO/TC 17, Steel, Subcommittee SC 20, General technical delivery conditions, sampling and mechanical testing methods.This second edition cancels and replaces the first edition (ISO 10474:1991), which has been technically revised.iv ISO 2013 All rights reservedBS ISO 10474:2013INTERNATIONAL STA

15、NDARD ISO 10474:2013(E)Steel and steel products Inspection documents1 ScopeThis International Standard defines the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of steel products.This International Standard is to

16、 be used in conjunction with other International Standards which specify the general technical delivery conditions: for steel and steel products, see ISO 404; for steel castings, see ISO 4990.NOTE This International Standard can also apply to other products.2 Normative referencesThe following refere

17、nced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 404:2013, Steel and steel products General technical delivery requ

18、irementsISO 4990, Steel castings General technical delivery requirements3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1non-specific inspectioninspection carried out by the manufacturer in accordance with his own procedures, to verify that produ

19、cts made by the same manufacturing process meet the requirements of the orderSOURCE: ISO 404:2013Note 1 to entry: The products inspected and tested can be different from the products actually supplied3.2specific inspectioninspection carried out, before delivery, in accordance with the product specif

20、ication, on the products being supplied or on test units of which the products are part, to verify that these products meet the requirements of the orderSOURCE: ISO 404:20133.3product specificationcomplete detailed technical requirements relevant for the order, stated in written form, e.g. reference

21、d standards or other specifications3.4manufacturerorganization that manufactures the respective products according to the requirements of the order and to properties specified in the referenced product specification ISO 2013 All rights reserved 1BS ISO 10474:2013ISO 10474:2013(E)3.5intermediaryorgan

22、ization that is supplied with products by the manufacturers and that then, in turn, supplies them without further processing or after processing without changing the properties specified in the purchase order and referenced product specificationNote 1 to entry: Examples of intermediaries can be stee

23、l service centres and stockists.4 Inspection documents based on non-specific inspection4.1 Declaration of compliance with the order “2.1”Document issued by the manufacturer declaring that the products supplied comply with the requirements of the order, without test results.4.2 Test report “2.2”Docum

24、ent issued by the manufacturer declaring that the products supplied comply with the requirements of the order and in which test results are supplied based on non-specific inspection.NOTE In nations or districts where submission of inspection certificate 2.3 of ISO 10474:1991 is specified in product

25、standards, 2.3 can be used until the product standard is revised.5 Inspection documents based on specific inspection5.1 Inspection certificate 3.1Document issued by the manufacturer declaring that the products supplied comply with the requirements of the order and in which test results are supplied

26、from specific inspection.The test unit and the tests carried out are defined by the product specification and/or the order.It shall be permissible for the manufacturer to transfer to the inspection certificate 3.1 relevant test results obtained by specific inspection on primary incoming products pro

27、vided that the manufacturer operates traceability procedures and can provide the corresponding inspection documents required.The document shall be validated by the manufacturers authorized inspection representative, independent of the manufacturing department.NOTE 1 In ISO 10474:1991, replaced by th

28、e current edition, the designation for this document is 3.1.B.NOTE 2 In nations or districts where submission of inspection certificate 3.1 B is specified in product standards, 3.1B instead of 3.1 can be used.5.2 Inspection certificate 3.2Document issued by the manufacturer declaring that the produc

29、ts supplied comply with the requirements of the order and in which test results are supplied from specific inspection.The test unit and the tests carried out are defined by the product specification and/or the order.It shall be permissible for the manufacturer to transfer to the inspection certifica

30、te 3.2 relevant test results obtained by specific inspection on primary incoming products provided that the manufacturer operates traceability procedures and can provide the corresponding inspection documents required.The inspection certificate shall be validated by both the manufacturers authorized

31、 representative and the purchasers authorized representative or by an inspector designated by a third party.2 ISO 2013 All rights reservedBS ISO 10474:2013ISO 10474:2013(E)6 Inspection documents supplied by an intermediaryWhen a product is supplied by an intermediary, the original or a copy of the m

32、anufacturers inspection document as specified in this International Standard shall be submitted to the purchaser. No change or addition to the inspection document is permitted.Copying (e.g. photocopying, scanning or similar techniques) of the original inspection document is permitted provided that t

33、raceability procedures are operated; the original document is available on request.If the intermediary has changed the identification, dimensions or quantity of the product in any way, an additional document shall be supplied for these new conditions, including suitable means of identification of th

34、e product, in order to ensure the traceability between the product and the documentation (see ISO 404). This shall also apply to all special requirements not included in the manufacturers inspection document. A modification of steel grade designation by the intermediary is not allowed, even if new t

35、esting is carried out.Any organization that during processing changes the metallurgical state of the product is considered as a product manufacturer.7 Validation of inspection documentsAll the inspection documents defined in this International Standard shall be validated by the person(s) responsible

36、 for this and their name(s) and position(s) shall be given. A signature is not required. Additional information on copies (see Clause 6) shall be validated in the same way.The retention and transmission of documents shall be either in electronic data or paper format.8 Summary of documentsA summary o

37、f documents covered by this International Standard is given in Table 1.Table 1 Summary of inspection documentsStandard desig-nationName of the documentType of inspec-tionContents of documentDocument validated by2.1Declaration of compliance with the orderNon-specificManufacturers declara-tion of comp

38、liance with the order without test resultsThe manufacturer2.2 Test repor tManufacturers declara-tion of compliance with the order, with test results based on non-specific inspection3.1 Inspection certificate 3.1SpecificManufacturers declara-tion of compliance with the order, with test results based

39、on specific inspectionThe manufacturers authorized inspection representative inde-pendent of the manufac-turing department3.2 Inspection certificate 3.2The manufacturers authorized inspec-tion representative and either purchasers authorized representa-tive or by an inspector designated by a third pa

40、rty. ISO 2013 All rights reserved 3BS ISO 10474:2013ISO 10474:2013(E)Bibliography1 ISO/NP 16228, Fastners Certificates Test reports4 ISO 2013 All rights reservedBS ISO 10474:2013BS ISO 10474:2013ISO 10474:2013(E) ISO 2013 All rights reservedICS 77.140.01Price based on 4 pagesThis page deliberately l

41、eft blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institu

42、tion (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefull

43、y assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out mo

44、re about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies

45、 can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further informat

46、ion on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards d

47、evelopments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards

48、 when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With upda

49、tes supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please infor