BS ISO 10889-2-2016 Tool holders with cylindrical shank Type A shanks for tool holders of special designs《圆柱形柄刀夹 A型专用刀夹柄》.pdf

1、BSI Standards PublicationBS ISO 10889-2:2016Tool holders with cylindricalshankPart 2: Type A, shanks for tool holders ofspecial designsBS ISO 10889-2:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10889-2:2016.It supersedes BS ISO 10889-2:2004 which is wi

2、thdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryp

3、rovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 90323 6ICS 25.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publis

4、hed under the authority of theStandards Policy and Strategy Committee on 31 March 2016.Amendments issued since publicationDate Text affectedBS ISO 10889-2:2016 ISO 2016Tool holders with cylindrical shank Part 2: Type A, shanks for tool holders of special designsPorte-outil queue cylindrique Partie 2

5、: Porte-outil de type A de conceptions spcialesINTERNATIONAL STANDARDISO10889-2Third edition2016-03-15Reference numberISO 10889-2:2016(E)BS ISO 10889-2:2016ISO 10889-2:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless oth

6、erwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

7、 below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 10889-2:2016ISO 10889-2:2016(E)Foreword iv1 Scope . 12 Normative references 13 Dimen

8、sions . 14 Designation 35 Technical delivery conditions . 3Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 . 4Bibliography 5 ISO 2016 All rights reserved iiiContents PageBS ISO 10889-2:2016ISO 10889-2:2016(E)ForewordISO (the International Organization

9、for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has t

10、he right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The proc

11、edures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editori

12、al rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights

13、identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanat

14、ion on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document

15、 is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces.This third edition cancels and replaces the second edition (ISO 10889-2:2004), of which it constitutes a minor revision, notably with the addition of Annex A, which gives the relationship between the designat

16、ions of this part of ISO 10889 and the ISO 13399 series.ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: Part 1: Cylindrical shank, location bore Technical delivery conditions Part 2: Type A, shanks for tool holders of special designs Part 3: Ty

17、pe B with rectangular radial seat Part 4: Type C with rectangular axial seat Part 5: Type D with more than one rectangular seat Part 6: Type E with cylindrical seat Part 7: Type F with taper seat Part 8: Type Z, accessoriesiv ISO 2016 All rights reservedBS ISO 10889-2:2016INTERNATIONAL STANDARD ISO

18、10889-2:2016(E)Tool holders with cylindrical shank Part 2: Type A, shanks for tool holders of special designs1 ScopeThis part of ISO 10889 specifies dimensions, designations and complementary technical delivery conditions for tool holders of type A with cylindrical shank in accordance with ISO 10889

19、-1 for tool holders of special designs.ISO 10889 is applicable to tool holders with cylindrical shank for machine tools with non-rotating tools, preferably for turning machines.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are ind

20、ispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolera

21、nce indicationsISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individual tolerance indicationsISO 10889-1, Tool holders with cylindrical shank Part 1: Cylindrical shank, location bore Technical delivery conditions3 DimensionsAll dimensions and tolerances are given

22、 in millimetres. Tolerancing is done according to ISO 8015. Tolerances not specified shall be of tolerance class “m” in accordance with ISO 2768-1 and of class “H” in accordance with ISO 2768-2.Unspecified details shall be chosen appropriately.The dimensions of tool holders type A shall be in accord

23、ance with the dimensions shown in Figures 1 and 2 and given in Table 1.The relationship between the symbols of this part of ISO 10889 and the symbols according to ISO 13399 is given in Annex A. ISO 2016 All rights reserved 1BS ISO 10889-2:2016ISO 10889-2:2016(E)Rz 100abl bhg2038dKeyaField of marking

24、.bCylindrical shank in accordance with ISO 10889-1.NOTE Surface roughness is given in micrometres.Figure 1 Type A1 tool holder, rectangularRz 100abg2038dl15g2038dKeyaField of marking.bCylindrical shank in accordance with ISO 10889-1.NOTE Surface roughness is given in micrometres.Figure 2 Type A2 too

25、l holder, round2 ISO 2016 All rights reservedBS ISO 10889-2:2016ISO 10889-2:2016(E)Table 1 Type A tool holder dimensionsDimensions in millimetresd1l1l2d2b h16 44 60 40 78 4420 65 70 50 100 6025 758058 100 6020030 8510068 130 7624040 10012083 151 9632050 12513598 160 12040060 160150123 165 12548080 2

26、00 500 158 220 1604 DesignationA tool holder in accordance with this part of ISO 10889 shall be designated by the following:a) “Tool holder”;b) reference to this part of ISO 10889, i.e. ISO 10889-2;c) type (A1 or A2);d) nominal diameter, d1, in millimetres;e) nominal length, l1or l2, in millimetres.

27、EXAMPLE 1 A tool holder of type A1 with a nominal diameter d1= 40 mm and a nominal length l1= 100 mm is designated as follows:Tool holder ISO 10889-2 - A1 - 40 100EXAMPLE 2 A tool holder of type A2 with a nominal diameter d1= 40 mm and a nominal length l2= 320 mm is designated as follows:Tool holder

28、 ISO 1088-2 - A2 - 40 3205 Technical delivery conditionsAs a complement to the requirements of ISO 10889-1, the material shall be indicated in the field of marking. ISO 2016 All rights reserved 3BS ISO 10889-2:2016ISO 10889-2:2016(E)Annex A (informative) Relationship between designations in this par

29、t of ISO 10889 and ISO 13399For the relationship between the symbols of this part of ISO 10889 and symbols according to ISO 13399, see Table A.1.Table A.1 Relationship between symbols in this part of ISO 10889 and ISO 13399 series Symbol in this part of ISO 10889Reference in this part of ISO 10889Pr

30、operty name in ISO 13399Symbol in ISO 13399Reference in ISO 13399 (BSU code)l1Figure 1 protruding length LPR 71DCD394BB20El2Figure 2 protruding length LPR 71DCD394BB20Eb Figure 1 overall width OAW 71CF299257986h Figure 1 overall height OAH 71D078EB73E87d1Figure 1 and Figure 2 connection diameter mac

31、hine sideDCONMS 71EBDBF5060E6d2Figure 2 body diameter BD 71ED6A9AF7D1D4 ISO 2016 All rights reservedBS ISO 10889-2:2016ISO 10889-2:2016(E)Bibliography1 ISO 8015, Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules2 ISO 13399 (all parts), Cutting tool data representat

32、ion and exchange ISO 2016 All rights reserved 5BS ISO 10889-2:2016ISO 10889-2:2016(E) ISO 2016 All rights reservedICS 25.060.20Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, informa

33、tion and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government

34、, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all

35、 sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying stan

36、dardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard co

37、pies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and ad

38、opted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format,

39、by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, plea

40、se visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Revisi

41、onsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre

42、.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed

43、 such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior writ

44、ten permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW