BS ISO 10904-2011 Fibre-cement corrugated sheets and fittings for roofing and cladding《屋顶和覆盖层纤维水泥波纹板及其配件》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 10904:2011Fibre-cement corrugated sheetsand fittings for roofing andcladdingBS ISO 10904:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementati

2、on of ISO 10904:2011.The UK participation in its preparation was entrusted to TechnicalCommittee B/3, Ad hoc co-ordination group for fibre reinforcedcement products.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to i

3、nclude all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 62440 7ICS 91.100.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Polic

4、y and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedBS ISO 10904:2011Reference numberISO 10904:2011(E)ISO 2011INTERNATIONAL STANDARD ISO10904First edition2011-08-01Fibre-cement corrugated sheets and fittings for roofing and cladding Plaques ondules en fibr

5、ociment et leurs accessoires pour couvertures et revtements BS ISO 10904:2011ISO 10904:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, inclu

6、ding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publish

7、ed in Switzerland ii ISO 2011 All rights reservedBS ISO 10904:2011ISO 10904:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Symbols, abbreviations and units .4 5 Product requirements .6 5.1 General .6 5.2

8、Categorization and classification 6 5.3 Dimensions and tolerances on nominal dimensions 8 5.4 Physical requirements and characteristics 9 5.5 Requirements concerning fire behavior .12 5.6 Product performance 12 5.7 Requirements concerning impact resistance.12 6 Evaluation of conformity 12 6.1 Genera

9、l .12 6.2 Type testing .12 6.3 Quality control (QC) system.13 6.4 Inspection of a consignment of finished products15 7 Test requirements .15 7.1 General .15 7.2 Dimensional and geometrical tests .15 7.3 Physical performance tests16 8 Marking.21 Annex A (normative) Consignment and inspection sampling

10、 .22 Annex B (normative) Dimensional and geometrical testing procedures23 Annex C (normative) Test method to determine the breaking load and the bending modulus of sheets .31 Annex D (normative) Test method to determine the bending moment of a sheet.35 Annex E (normative) Statistical method for dete

11、rmining the corresponding wet values or revised dry specifications for the breaking load and/or bending moment when carrying out the dry method of test or when testing prior to coating for quality control purposes.37 Annex F (normative) Test method to determine the apparent density .40 Annex G (norm

12、ative) Test method to determine the water permeability of a sheet 42 Annex H (normative) Test method to determine the freeze-thaw performance of sheets and fittings.44 Annex I (normative) Test method to determine the heat-rain performance of sheets.47 Annex J (normative) Test method to determine the

13、 warm water performance of long and short sheets .49 Annex K (normative) Test method to determine the soak-dry performance of long and short sheets .51 Bibliography53 BS ISO 10904:2011ISO 10904:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) i

14、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe

15、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are d

16、rafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International

17、Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10904 was prepar

18、ed by Technical Committee ISO/TC 77, Products in fibre reinforced cement. This first edition of ISO 10904 cancels and replaces ISO 9384:1991 and ISO 9933:1995, which have been technically revised. BS ISO 10904:2011ISO 10904:2011(E) ISO 2011 All rights reserved vIntroduction The performance of a roof

19、 or another building part constructed with the products covered by this International Standard depends not only on the properties of the products as required by this International Standard, but also on the design, construction and installation of the components as a whole relative to the environment

20、 and the conditions of use. This International Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets. BS ISO 10904:2011BS ISO 10904:2011INTERNATIONAL STANDARD ISO 10904:2011(E) ISO 2011 All righ

21、ts reserved 1Fibre-cement corrugated sheets and fittings for roofing and cladding 1 Scope This International Standard specifies technical requirements and methods for the inspection and testing of straight short and long fibre-cement profiled sheets and their fibre-cement fittings designed to provid

22、e the weather-exposed surfaces on roofs and internal and external walls of buildings. Products covered by this International Standard can be used for other purposes, provided they comply with the appropriate national or international application code or standard. Some of the requirements of this Int

23、ernational Standard can apply, after agreement between manufacturer and purchaser, to curved profiled sheets. The type tests described in this International Standard are not intended to evaluate the performance of the coating in isolation (colour-fastness, adhesion, etc.). Specific performance requi

24、rements for coatings are referenced in other International Standards or national standards. This International Standard does not apply to fibre-cement profiled sheets and fittings reinforced with asbestos fibres. 2 Normative references The following referenced documents are indispensable for the app

25、lication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 390:1993, Products in fibre-reinforced cement Sampling and inspection ISO 2602:1980, Statistical interpretati

26、on of test results Estimation of the mean Confidence interval ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection ISO 3951-1, Sampling procedures for inspection by variables Part 1: Specification fo

27、r single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL ISO 12468-1, External exposure of roofs to fire Part 1: Test method ISO 12468-2, External fire exposure to roofs Part 2: Classification of roofs EN 15057,

28、Fibre cement profiled sheets Impact resistance test method BS ISO 10904:2011ISO 10904:2011(E) 2 ISO 2011 All rights reserved3 Terms and definitions For the purposes of this document, the following definitions apply. 3.1 profiled sheet component whose cross-section consists of corrugations NOTE 1 Exa

29、mples are shown in Figure 1. NOTE 2 The corrugations are defined by their pitch, a, and their height, h. Key A upper face Figure 1 Examples of categorization by height of profile BS ISO 10904:2011ISO 10904:2011(E) ISO 2011 All rights reserved 33.2 side corrugation corrugation at the extreme end(s) o

30、f a cross section normally having a different pitch and height, normally used for side overlapping 3.3 acceptance test test to establish whether a batch of products conforms to a specification NOTE 1 The test is performed on samples drawn from continuous production or from a consignment. NOTE 2 Test

31、 methods, specifications and limit values are specified in this International Standard. Sampling levels and acceptance criteria are specified in 6.3. NOTE 3 See ISO 390. 3.4 type test test performed to demonstrate conformity with the requirements of this International Standard or for the approval of

32、 a new product and/or when a fundamental change is made in formulation and/or method of manufacture, the effects of which cannot be predicted on the basis of previous experience NOTE The test is performed on the as-delivered product, but is not required for each production batch. 3.5 acceptable qual

33、ity level AQL maximum percent defective (or maximum number of defects per 100 units) that can be considered satisfactory as a long-term average quality level in a sampling plan NOTE When a manufacturers process satisfies a sampling scheme with an AQL of 4 %, this indicates that 96 % of the inspected

34、 product exceeds the specification. This type of specification provides the consumer with a clearly defined lower quality boundary; this does not occur if acceptance is based solely on the average value of the measured property. Examples of sampling schemes can be found in ISO 390, ISO 2859-1 and IS

35、O 3951-1. 3.6 as delivered in the same condition as that in which the producer intends to supply the product after completing all aspects of the process, including maturing and, when appropriate, painting 3.7 reinforcement fibres organic or inorganic reinforcement fibres for the manufacture of fibre

36、-cement profiled sheets and fittings complying with this International Standard NOTE See 5.1. 3.8 apparent density dry mass per unit volume based upon the volume of the sample calculated by water displacement or equivalent NOTE This is an average density of the material and pores, coated or uncoated

37、 (as delivered). 3.9 breaking load maximum load achieved during the bending test and representing the load-bearing capacity of the sheets at the test span BS ISO 10904:2011ISO 10904:2011(E) 4 ISO 2011 All rights reserved3.10 bending moment at rupture moment at mid-span calculated from the maximum lo

38、ad during the bending test 3.11 short sheet sheet with a length less than or equal to 0,9 m 3.12 long sheet sheet with a length greater than 0,9 m 3.13 upper face face normally exposed to the weather 3.14 under face reverse of the upper face 3.15 ambient laboratory conditions atmosphere for testing

39、or storing and conditioning of samples, defined for the purpose of this International Standard as a temperature of 23 C 10 C and a relative humidity of 50 % 20 % 3.16 fitting components with particular shapes that are fitted to profiled sheets and complete, for instance, the roofing at the verge, ri

40、dge and eaves, or perform functions such as ventilation, daylight-admission, etc. 3.17 bending modulus modulus of elasticity derived from the load-deflection data recorded during the breaking load test 4 Symbols, abbreviations and units For the purposes of this document, the following symbols and ab

41、breviations are used. a pitch of the corrugation, expressed in millimetres b dimension of the specimen parallel to the supports in either the breaking load test (called width of the specimen) or the bending moment test (called length of the specimen), expressed in millimetres e thickness of the shee

42、t, expressed in millimetres Embending modulus, expressed in newtons per square millimetre, in the breaking load test f0,15deflection, expressed in millimetres, at approximately 15 % of the maximum load in the breaking load test f0,55deflection, expressed in millimetres, at approximately 55 % of the

43、maximum load in the breaking load test F load at rupture in the breaking load test or bending moment test, expressed in newtons Fsload at rupture per metre width from the breaking load test, expressed in newtons per metre F0,15load, expressed in newtons, at 15 % of the maximum load in the breaking l

44、oad test BS ISO 10904:2011ISO 10904:2011(E) ISO 2011 All rights reserved 5F0,55 load, expressed in newtons, at 55 % of the maximum load in the breaking load test h height of the corrugation, expressed in millimetres hodheight of the edge of the descending corrugation, expressed in millimetres homhei

45、ght of the edge of the ascending corrugation, expressed in millimetres I moment of inertia of the section around a horizontal axis through the centre of gravity, expressed in millimetres l length of the sheet, expressed in millimetres lsclear span between the supports in the breaking load test or th

46、e bending moment test, expressed in millimetres L1upper estimation at 95 % confidence level of the result X1L2lower estimation at 95 % confidence level of the result X2m mass of the specimen, expressed in grams, after drying, when determining the apparent density M bending moment at rupture per metr

47、e length from the bending moment test, expressed in newton-metres per metre RLratio of the estimation L2to the estimation L1s1standard deviation of the specimens with average X1s2standard deviation of the specimens with average X2V apparent volume, expressed in cubic centimetres, of the specimens fo

48、r the apparent density test w width of the sheet, expressed in millimetres xoactual result obtained when dry-testing 1X mean value of the bending test results of the control specimens (the first lot) for a type test 2X mean value of the bending test results of the specimens (the second lot) after a

49、type-test exposure xstd minimum value for use as the specification for the dry method of test; this value is calculated at the 97,5 % lower confidence level from the value ystd specified for the wet method of test in this International Standard yo value calculated from the value obtained from a specimen tested dry, which is the estimate at the 97,5 % lower confidence level of the value expected from a specimen tested wet ystd minimum value specified in this International Standard for wet testing one of the coefficients o