BS ISO 10911-2017 Solid hardmetal end mills with cylindrical shank Dimensions《带圆柱形柄的实心硬质球端立铣刀 尺寸》.pdf

1、Solid hardmetal end mills with cylindrical shank DimensionsBS ISO 10911:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Solid hardmetal end mills with cylindrical shank DimensionsFraises cylindriques deux tailles monobloc en mtaux-durs DimensionsINTERNAT

2、IONAL STANDARDISO10911Third edition2017-06Reference numberISO 10911:2017(E)National forewordThis British Standard is the UK implementation of ISO 10911:2017. It supersedes BS ISO 10911:2010, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools

3、 tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standar

4、ds Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 91077 7ICS 25.100.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.A

5、mendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 10911:2017 ISO 2017Solid hardmetal end mills with cylindrical shank DimensionsFraises cylindriques deux tailles monobloc en mtaux-durs DimensionsINTERNATIONAL STANDARDISO10911Third edition2017-06Reference numberISO

6、 10911:2017(E)BS ISO 10911:2017ISO 10911:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic o

7、r mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Genev

8、a, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 10911:2017ISO 10911:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reprod

9、uced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.

10、ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 10911:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Dimensions . 15 Centre cutting 1Annex A (informative) Rela

11、tionship between designations in this document and the ISO 13399 series . 3Bibliography 4 ISO 2017 All rights reserved iiiContents PageBS ISO 10911:2017ISO 10911:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member

12、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental

13、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance ar

14、e described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention i

15、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/o

16、r on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

17、 expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 29,

18、Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This third edition cancels and replaces the second edition (ISO 10911:2010), which has been technically revised as follows: Figure 1 has been revised; Annex A has been added, showing the relationship between designations

19、 in this document and the ISO 13399 series.iv ISO 2017 All rights reservedBS ISO 10911:2017ISO 10911:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is no

20、rmally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in

21、 the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular

22、the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this

23、document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .i

24、so .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as inf

25、ormation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting ed

26、ges, cutting items.This third edition cancels and replaces the second edition (ISO 10911:2010), which has been technically revised as follows: Figure 1 has been revised; Annex A has been added, showing the relationship between designations in this document and the ISO 13399 series.iv ISO 2017 All ri

27、ghts reserved INTERNATIONAL STANDARD ISO 10911:2017(E)Solid hardmetal end mills with cylindrical shank Dimensions1 ScopeThis document specifies the dimensions of solid hardmetal end mills with cylindrical shank.NOTE For the relationship between designations in this document and the ISO 13399 series,

28、 see Annex A.2 Normative referencesThere are no normative references in this document.3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t

29、p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 DimensionsThe dimensions of solid hardmetal end mills with plain cylindrical shanks are specified in Figure 1 and Table 1.NOTE The dimensions given in Table 1 also apply to solid hardmetal end mill

30、s with flatted cylindrical shanks in accordance with ISO 3338-2.5 Centre cuttingEnd mills with two flutes shall be centre-cutting (slot drills).End mills with three flutes or more may be centre-cutting.1ddlKey1 plain cylindrical shank in accordance with ISO 3338-1NOTE See Table 1 for dimensions.Figu

31、re 1 Example of an end mill ISO 2017 All rights reserved 1BS ISO 10911:2017ISO 10911:2017(E)Table 1 Dimensions of end mills with two flutesDimensions in millimetresCutting diameterShank diameteraShort cutting part Long cutting partOverall lengthCutting lengthOverall lengthCutting lengthd1d2l1bl2cl1d

32、l2h10 h6 2 or 3 cutting edges4 cutting edges2 or 3 cutting edges4 cutting edges1,0 3,0 38,0 3,0 3,0 1,5 3,0 38,0 3,0 4,0 2,03,0 38,0 3,0 4,0 38,0 6,0 7,06,0 50,0 3,0 4,0 57,0 6,0 7,02,53,0 38,0 3,0 4,0 38,0 7,0 8,06,0 50,0 3,0 4,0 57,0 7,0 8,03,03,0 38,0 4,0 5,0 38,0 7,0 8,06,0 50,0 4,0 5,0 57,0 7,0

33、 8,03,5 6,0 50,0 4,0 6,0 57,0 7,0 10,04,0 6,0 54,0 5,0 8,0 57,0 8,0 11,04,5 6,0 54,0 5,0 8,0 57,0 8,0 11,05,0 6,0 54,0 6,0 9,0 57,0 10,0 13,06,0 6,0 54,0 7,0 10,0 57,0 10,0 13,07,0 8,0 58,0 8,0 11,0 63,0 13,0 16,08,0 8,0 58,0 9,0 12,0 63,0 16,0 19,09,0 10,0 66,0 10,0 13,0 72,0 16,0 19,010,0 10,0 66,

34、0 11,0 14,0 72,0 19,0 22,012,0 12,0 73,0 12,0 16,0 83,0 22,0 26,014,0 14,0 75,0 14,0 18,0 83,0 22,0 26,016,0 16,0 82,0 16,0 22,0 92,0 26,0 32,018,0 18,0 84,0 18,0 24,0 92,0 26,0 32,020,0 20,0 92,0 20,0 26,0 104,0 32,0 38,0aFor the dimensions, see ISO 3338-1.bTolerance on l1, short cutting part: 020+

35、 ,mm.cTolerances on l2: for l2 10 mm: 010+ ,mm; for l21122 mm: 015+ ,mm; for l2 22 mm: 020+ ,mm.dTolerance on l1, long cutting part: 020+ ,mm.2 ISO 2017 All rights reservedBS ISO 10911:2017ISO 10911:2017(E)Table 1 Dimensions of end mills with two flutesDimensions in millimetresCutting diameterShank

36、diameteraShort cutting part Long cutting partOverall lengthCutting lengthOverall lengthCutting lengthd1d2l1bl2cl1dl2h10 h6 2 or 3 cutting edges4 cutting edges2 or 3 cutting edges4 cutting edges1,0 3,0 38,0 3,0 3,0 1,5 3,0 38,0 3,0 4,0 2,03,0 38,0 3,0 4,0 38,0 6,0 7,06,0 50,0 3,0 4,0 57,0 6,0 7,02,53

37、,0 38,0 3,0 4,0 38,0 7,0 8,06,0 50,0 3,0 4,0 57,0 7,0 8,03,03,0 38,0 4,0 5,0 38,0 7,0 8,06,0 50,0 4,0 5,0 57,0 7,0 8,03,5 6,0 50,0 4,0 6,0 57,0 7,0 10,04,0 6,0 54,0 5,0 8,0 57,0 8,0 11,04,5 6,0 54,0 5,0 8,0 57,0 8,0 11,05,0 6,0 54,0 6,0 9,0 57,0 10,0 13,06,0 6,0 54,0 7,0 10,0 57,0 10,0 13,07,0 8,0 5

38、8,0 8,0 11,0 63,0 13,0 16,08,0 8,0 58,0 9,0 12,0 63,0 16,0 19,09,0 10,0 66,0 10,0 13,0 72,0 16,0 19,010,0 10,0 66,0 11,0 14,0 72,0 19,0 22,012,0 12,0 73,0 12,0 16,0 83,0 22,0 26,014,0 14,0 75,0 14,0 18,0 83,0 22,0 26,016,0 16,0 82,0 16,0 22,0 92,0 26,0 32,018,0 18,0 84,0 18,0 24,0 92,0 26,0 32,020,0

39、 20,0 92,0 20,0 26,0 104,0 32,0 38,0aFor the dimensions, see ISO 3338-1.bTolerance on l1, short cutting part: 020+ ,mm.cTolerances on l2: for l2 10 mm: 010+ ,mm; for l21122 mm: 015+ ,mm; for l2 22 mm: 020+ ,mm.dTolerance on l1, long cutting part: 020+ ,mm.2 ISO 2017 All rights reserved ISO 10911:201

40、7(E)Annex A (informative) Relationship between designations in this document and the ISO 13399 seriesA.1 Relationship between designationsFor the relationship between the designations in this document and preferred symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship betwe

41、en designations in this document and the ISO 13399 seriesSymbol in this documentReference in this documentProperty name in the ISO 13399 seriesSymbol in the ISO 13399 seriesReference in the ISO 13399 seriesd1Figure 1Table 1Cutting diameter DC 71D084653E57Fd2Figure 1Table 1Connection diameter ma-chin

42、e sideDCONMS 71EBDBF5060E6d2 h6Table 1Tolerance class connection diameter machine sideTCDCONMS 72719B2BD8041l1Figure 1Table 1Overall length OAL 71D078EB7C086l2Figure 1Table 1Depth of cut maximum APMX 71D07576C0558 ISO 2017 All rights reserved 3BS ISO 10911:2017ISO 10911:2017(E)Bibliography1 ISO 3338

43、-1, Cylindrical shanks for milling cutters Part 1: Dimensional characteristics of plain cylindrical shanks2 ISO 3338-2, Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks4 ISO 2017 All rights reservedBS ISO 10911:2017This page deliberately left b

44、lankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution

45、(BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open co

46、nsultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacti

47、ng our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign stan

48、dards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in th

49、e information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written