BS ISO 10914-1998 Assembly tools for screws and nuts - Sockets and wrenches for spline drive《螺钉和螺母用安装工具 开键槽用套管扳手》.pdf

1、BRITISH STANDARD BS ISO 10914:1996 Assembly tools for screws and nuts Sockets and wrenches for spline drive ICS 25.140.30BSISO10914:1996 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes in

2、toeffect on 15 February 1998 BSI 04-1999 ISBN 0 580 29364 5 National foreword This British Standard reproduces verbatim ISO 10914:1996 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee MTE/15, Hand tools, to Subcommittee MTE/1

3、5/13, Spanners and screwdrivers, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Euro

4、pean developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI St

5、andards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsibl

6、e for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, page ii, pages 1 to 8 and a back cover. This standard has b

7、een updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO10914:1996 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword ii 1

8、 Scope 1 2 Normative references 1 3 Classification 1 4 Dimensions 1 5 Technical requirements 1 6 Designation 1 7 Marking 2 Figure 1 Socket for spline drive 2 Figure 2 Universal joint for spline drive 5 Figure 3 Box wrench head dimensions and torque requirements 6 Figure 4 Box wrench, double head, fo

9、r spline drive 7 Table 1 Socket dimensions, driving squares 6,3 mm and 10 mm 2 Table 2 Socket dimensions, driving squares 12,5 mm and 20 mm 3 Table 3 Socket dimensions, driving squares 25 mm and 40 mm 3 Table 4 Socket torque requirements 4 Table 5 Universal joint dimensions 5 Table 6 Universal joint

10、 torque requirements 6 Table 7 Box wrench head dimensions and torque requirements 7 Table 8 Box wrench, double head, 15 offset length requirements 8ii blankBSISO10914:1996 ii BSI 04-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards

11、 bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organiza

12、tions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circu

13、lated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO 10914 was prepared by Technical Committee ISO/TC29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pl

14、iers and nippers. Descriptors: Tools, assembly tools, hand tools, wrenches, socket wrenches, classification, specifications, dimensions, designat marking, interchangeability.BSISO10914:1996 BSI 04-1999 1 1 Scope This International Standard specifies the technical, dimensional and test requirements f

15、or hand-operated sockets and box wrenches used for the attachment and detachment of metric spline drive fasteners according to ISO7403. It applies to tools listed in the classification of clause3. This type of tool is mainly used in the aeronautic industry. The overall dimensions are not in accordan

16、ce with other International Standards relating to dimensions. NOTEThe figures in this International Standard are descriptive, not restrictive, and are not intended to exclude any sockets and box wrenches provided they be in accordance with this International Standard. 2 Normative references The foll

17、owing standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are enc

18、ouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1174-1:1996, Assembly tools for bolts and screws Driving squares Part 1: Driving squares for hand so

19、cket tools. ISO 6508:1986, Metallic materials Hardness test Rockwell Test (scales A-B-C-D-E-F-G-H-K). ISO 7403:1983, Fasteners for aerospace construction Spline drive wrenching configuration Metric series. 3 Classification The following types and classes apply: Type I: Sockets Class A: Regular Class

20、 B: Long Class C: Universal joint Type II: Box wrench, double head, 15 offset Class D: Short length Class E: Regular length Class F: Long length 4 Dimensions Female square dimensions shall conform to ISO1174-1. Spline drive size shall conform to ISO 7403. Socket dimensions shall conform to the dimen

21、sions given in Table 1, Table 2, Table 3 and Table 5. Wrench dimensions shall conform to those given in Table 7 andTable 8. 5 Technical requirements 5.1 Hardness The sockets and wrenches shall have a hardness of40HRC to54HRC when tested in accordance with the conditions specified in ISO6508. 5.2 Tes

22、t mandrels Mandrels shall be hardened to55HRC minimum and have smoothly finished wrench engagement surfaces. Mandrel engagement lengths shall conform to Table 4 and Table 6 for the sockets, and to Table 7 for the wrenches. The spline mandrels shall conform to the minimum dimensions specified in ISO7

23、403 with tolerance h8. 5.3 Endurance test A socket or wrench, when tested, shall be capable of withstanding2000 applications of the torque cyclic fatigue load when engaged with a spline mandrel. Cyclic load shall be applied at a rate of60cycles per minute maximum. The sample tool shall be capable of

24、 withstanding the proof load following the cyclic load test. 6 Designation A socket or universal joint for spline drive according to this International Standard shall be designated by a) “Socket”; b) reference to this International Standard; c) nominal dimension of driving square, in millimetres; d)

25、 nominal size of spline drive, in millimetres; e) class. EXAMPLES Socket for spline drive of class B with a6,3 mm driving square and nominal wrenching size of10mm is designated as follows: Socket ISO 10914 6,3 10 B Universal joint (class C) for spline drive with a12,5mm driving square and nominal wr

26、enching size of18 mm is designated as follows: Socket ISO 10914 12,5 18 C A box wrench, double head, 15 offset, for spline drive according to this International Standard shall be designated by a) “Box wrench”; b) reference to this International Standard;BSISO10914:1996 2 BSI 04-1999 c) pairing of no

27、minal spline drive sizes, in millimetres; d) class. EXAMPLE Box wrench, double head, for spline drive of class D, with a7mm 8mm pairing of nominal spline drive size is designated as follows: Box wrench ISO 10914 7 8 D 7 Marking Sockets and wrenches shall be marked, permanently and legibly, with the

28、following information: name or trademark of the manufacturer (or distributor); nominal size of spline drive. Table 1 Socket dimensions, driving squares 6,3 mm and 10 mm Figure 1 Socket for spline drive Dimensions in millimetres Nominal spline drive size Dimensions for all driving squares Driving squ

29、ares 6,3 10 Class A Class B Class A Class B a d g b c e c e b c e c e max. min. min. max. min. max. min. max. max. min. max. min. max. 5 5,5 6 7 8 9 10 11 12 13 14 7,8 8,5 9,1 10,5 11,8 13,3 14,6 16,1 17,5 19,1 20,6 4,8 5,2 5,6 6,9 8,4 8,6 9,1 10,4 11,2 11,8 12,1 4,5 5 5,5 6,5 7,5 8,5 9,5 10,5 11,5

30、12,5 13,5 11,2 11,2 11,2 11,2 11,8 5 5,5 6 8 26 26 26 26 26 25 25,5 26 28 50 50 50 50 50 13,3 14,6 26 26 50 50 16,9 17 17,5 17,5 19,1 20,6 5 6 8 26 27,5 28,5 31 33,5 33,5 25 26 28 50 50 50 50 50 50BSISO10914:1996 BSI 04-1999 3 Table 2 Socket dimensions, driving squares 12,5 mm and 20 mm Table 3 Sock

31、et dimensions, driving squares 25 mm and 40 mm Dimensions in millimetres Nominal spline drive size Dimensions for all driving squares Driving squares 12,5 20 Class A Class B Class A Class B a d g b c e c e b c e c e max. min. min. max. min. max. min. max. max. min. max. min. max. 12 13 14 15 16 17 1

32、8 17,5 19,1 20,6 22,2 23,2 24,8 26,2 11,2 11,8 12,1 12,7 13,6 14 14,7 11,5 12,5 13,5 14,5 15,5 16,5 17,5 22,2 22,2 22,2 22,2 23,2 24,8 26,2 8 8 8 33,5 33,5 33,5 39,5 39,5 39,5 39,5 52 52 52 81 81 81 81 81 81 81 19 26,7 15,7 18,5 26,7 39,5 81 34,9 10 46 21 29,2 17 20,5 29,2 39,5 81 34,9 12 46,5 22 30

33、,5 18 21,5 30,5 39,5 81 34,9 14 47,5 24 33 19,9 23,5 34,9 51 27 38,9 22,2 26,5 34,9 53 Dimensions in millimetres Nominal spline drive size Dimensions for all driving squares Driving squares 25 40 Class A Class B Class A Class B a d g b c e c e b c e c e max. min. min. max. min. max. min. max. max. m

34、in. max. min. max. 27 30 32 38,9 43,1 45,9 22,2 25,4 26,9 26,5 29,5 31,5 51 51 51 12 18 20 65 68,5 74,5 36 51,4 30,2 35,5 51,4 78 76,2 29 86,5 40 57 34,3 39,5 57 84 76,2 31 90 41 58,4 35 40,5 76,2 32 91 46 65,4 39,6 45,5 76,2 36 95,5 50 71 43,4 49,5 76,2 40 99,5 BSISO10914:1996 4 BSI 04-1999 Table 4

35、 Socket torque requirements Nominal spline drive size Test mandrel engagement length Driving squares mm 6,3 10 12 20 25 40 Torque requirements Nm mm max. mm Cyclic load Proof load Cyclic load Proof load Cyclic load Proof load Cyclic load Proof load Cyclic load Proof load Cyclic load Proof load 5 5,5

36、 6 7 8 2,5 2,8 3 3,5 4 20 25 25 35 55 30 35 40 55 80 9 4,5 55 80 95 140 10 5 55 80 135 195 11 5,5 170 250 12 6 200 280 290 420 13 6,5 200 280 380 550 14 7 200 280 480 690 15 7,5 200 280 530 750 16 8 200 280 550 790 17 8,5 550 790 18 9 550 790 19 9,5 550 790 700 1000 21 10,5 550 790 950 1350 22 11 55

37、0 790 1100 1580 24 12 1460 2140 27 13,5 1550 2260 2050 3050 30 15 2800 4100 32 16 3300 4850 36 18 3500 5300 4900 7000 40 20 3500 5300 6700 9600 41 20,5 7300 10500 46 23 10400 14900 50 25 12500 18000BSISO10914:1996 BSI 04-1999 5 Table 5 Universal joint dimensions Figure 2 Universal joint for spline d

38、rive Dimensions in millimetres Nominal spline drive size Dimensions for all driving squares Driving squares 6,3 10 12,5 a d g b c e b c e b c e max. min. min. max. min. max. min. min. max. min. min. max. 5 7,8 4,8 4,5 13,1 1 30 5,5 8,5 5,2 5 13,1 1,5 32 6 9,1 5,6 5,5 13,1 2 33,5 7 10,5 6,9 6,5 13,1

39、3,5 34,5 8 11,8 8,4 7,5 13,1 5 39,5 9 13,3 8,6 8,5 13,1 41,5 19,1 2 51,5 10 14,6 9,1 9,5 13,1 43 19,1 4 52,5 11 16,1 10,4 10,5 19,1 5 53,5 12 17,5 11,2 11,5 19,1 6 54,5 28,6 6 72,5 13 19,1 11,8 12,5 19,1 55 28,6 7 72,5 14 20,6 12 13,5 19,1 55,5 28,6 8 75 15 22,2 12,7 14,5 19,1 56,5 28,6 9 76 16 23,2

40、 13,6 15,5 19,1 57 28,6 10 76 17 24,8 14 16,5 28,6 11 78 18 26,2 14,7 17,5 28,6 12 78 19 26,7 15,7 18,5 28,6 13 80 21 29,2 17 20,5 28,6 82 22 30,5 18 21,5 28,6 83 24 33 19,9 23,5 28,6 87BSISO10914:1996 6 BSI 04-1999 Table 6 Universal joint torque requirements Nominal spline drive size Test mandrel e

41、ngagement length Driving squares mm 6,3 10 12,5 Torque requirements max. Nm mm mm Cyclic load Proof load Cyclic load Proof load Cyclic load Proof load 5 2,5 20 30 5,5 2,8 25 35 6 3 25 40 7 3,5 35 55 8 4 40 60 9 4,5 40 60 75 110 10 5 40 60 75 110 11 5,5 75 110 12 6 75 110 135 200 13 6,5 75 110 135 20

42、0 14 7 75 110 135 200 15 7,5 75 110 135 200 16 8 75 110 135 200 17 8,5 135 200 18 9 135 200 19 9,5 135 200 21 10,5 135 200 22 11 135 200 24 12 135 200 Figure 3 Box wrench head dimensions and torque requirementsBSISO10914:1996 BSI 04-1999 7 Table 7 Box wrench head dimensions and torque requirements N

43、ominal spline drive opening a b Test mandrel engagement length Torque requirements Nm max. min. max. Cyclic load Proof load mm mm mm mm 5 5,5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 24 27 9,1 9,7 10,3 11,6 12,8 15 16,1 17,3 18,9 19,9 21 22,1 23,2 25,3 26,5 27,7 29,9 32,1 37,1 38,2 5,2 6 6,4 6,4

44、8,6 8,6 9,5 9,5 9,5 9,9 10,3 11,4 11,9 13,1 13,3 13,5 13,9 14,3 15,1 17 2,5 2,8 3 3,5 4 4,5 5 5,5 6 6,5 7 7,5 8 8,5 9 9,5 10,5 11 12 13,5 16 19 22 25 28 58 79 99 138 178 200 220 235 315 320 330 460 520 800 810 27 30 34 41 51 83 112 141 198 255 295 340 365 480 495 510 710 810 1200 1240 Figure 4 Box w

45、rench, double head, for spline driveBSISO10914:1996 8 BSI 04-1999 Table 8 Box wrench, double head, 15 offset length requirements Dimensions in millimetres Nominal spline drive pairing Class D Class E Class F l s 1 s 2 min. max. min. max. min. max. 5 5,5 5 7 6 7 7 8 8 10 9 10 10 11 10 13 11 13 12 14

46、13 15 14 16 15 16 16 18 17 19 18 21 19 21 21 24 22 24 24 27 80 85 90 100 105 115 120 130 130 135 145 155 155 165 175 195 195 220 220 235 100 105 115 125 135 140 145 165 165 175 190 200 200 210 220 250 250 280 280 300 110 115 125 135 150 155 160 180 180 190 205 215 215 225 240 270 270 290 290 320 135

47、 140 150 160 175 180 190 210 210 220 235 250 250 260 275 305 305 340 340 365 170 175 190 200 220 225 240 260 260 275 290 305 305 320 340 370 370 400 400 440 205 210 220 235 255 260 275 295 295 310 325 340 340 355 375 405 405 445 445 485 NOTESize pairings shown in brackets are not recommended sizes.b

48、lankBS ISO 10914:1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone find