BS ISO 10945-2000 Hydraulic fluid power - Gas-loaded accumulators - Dimensions of gas ports《液压传动 充气蓄能器 气口的尺寸》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 10945:1994 ICS 23.

2、100.99 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Hydraulic fluid power Gas-loaded accumulators Dimensions of gas portsThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards C

3、ommittee and comes into effect on 15 November 2000 BSI 11-2000 ISBN 0 580 36653 7 BS ISO 10945:1994 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 10945:1994 and implements it as the UK national standard. It supersedes BS 72

4、01-2:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems and components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on t

5、he interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Stand

6、ards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not p

7、urport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside fron

8、t cover, the ISO title page, page ii, pages 1 and 2, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.INTERNATIONAL STANDARD ISO 10945 First edition 1994-11-15 Hydraulic fluid power - Gas-loaded accumulators - Dime

9、nsions of gas ports Transmissions hydrauliques - Accumulateurs hydropneumatiques - Dimensions des orifices gaz Reference number ISO 10945:1994(E) ISO 10945:1994(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bod

10、ies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

11、 non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (1 EC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bo

12、dies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10945 was prepared by Technical Committee lSO/TC 131, Fluid power Systems. 0 OSI 4991 llA sthgir .devreser sselnU esiwrehto ,deificeps on ttap

13、fo siht noitacilbup yam eb decudorper ro dezilitu ni yna mrof ro yb yna ,snaem crnortcele ro ,lacrnahcem gnidulcni gniypocotohp dna ,mliforcim tuohtiw noissimreP ni gnitirw morf eht .rehsilbup lanoitanretnI noitazinagrO rof noitazidradnatS esaC elatsoP 65 l l-HC 112 eveneG 02 l dnalreztiwS detnirP n

14、i dnalreztiwS ii INTERNATIONAL STANDARD 0 OSI ISO 10945:1994(E) Hydraulic fluid power - Gas-loaded accumulators - Dimensions of gas ports 1 Scope This International Standard specifies the types and the dimensions of the gas filling ports of gas-loaded ac- cumulators used in hydraulic fluid power Sys

15、tems. lt describes two male ports for filling the gas side of a gas-loaded accumulator. These ports are designated by the following: - male port with M16 x 2 thread, in accordance with ISO 261 and ISO 724, which is preferred for new designs (see 4.1); - male port with 8Vl thread in accordance with I

16、SO 4570-1 (see 4.2). ISO 724: 1993, ISO general-purpose metric screw threads - Basic dimensions. ISO 4570-1 :1977, Tyre valve threads - Part 1. Threads 5V1, 5V2, 6VI and 8Vl. ISO 5598:1985, Fluid power Systems and compo- nen ts - Vocabulary. 3 Definitions For the purposes of this International Stand

17、ard, the definitions given in ISO 5598 apply. 4 Dimensions 4.1 For a male port with M16 x 2 threads, the di- mensions shall conform to those shown in figure 1. 2 Normative references The following Standards contain provisions which, through reference in this text, constitute provisions of this Inter

18、national Standard. At the time of publi- cation, the editions indicated were valid. All Standards are subject to revision, and Parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most re- cent editions of the Standards indicated be

19、low. Members of IEC and ISO maintain registers of cur- rently valid International Standards. ISO 261:1, ISO general-purpose me tric scre w threads - General plan. 4.2 For a male port with 8Vl thread the dimensions shall conform to those shown in figure2. 5 Identification Statement (Reference to this

20、 International Standard) lt is recommended to manufacturers to use the fol- lowing Statement in test reports, catalogues and sales Iiterature when electing to comply with this Inter- national Standard: “Gas ports for gas-loaded accumulators conforming to ISO 10945: 1994, Hydraulic fluid power - Gas-

21、 loaded accumula tors - Dimensions of gas ports .” 1) To be published. (Revision of ISO 261:1973) 1 ISO 10945:1994(E) 0 OSI . .- I E M Dimensions in millimetres, surface roughness in micrometres 2:l ,- Valve stem 1) In accordance with ISO 261 and ISO 724. Figure 1 - Dimensions for male port with M16

22、 x 2 threads (to be used for new designs) Dimensions in millimetres, surface roughness in micrometres 2:l Thread 8Vl” Valve stem Ln Cu 1) In accordance with ISO 4570-1. Figure 2 - Dimensions for male port 8Vl aJ U .- z -IJ 5” l d c U L 0 u- - 2 d e BS ISO 10945:1994 BSI 389 Chiswick High Road London

23、 W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI

24、is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make s

25、ure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee respon

26、sible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, inter

27、national and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise

28、requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and se

29、rvices. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.

30、Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,

31、stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or

32、 grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.