BS ISO 10946-1999 Hydraulic fluid power - Gas-loaded accumulators with separator - Selection of preferred hydraulic ports《液压传动 隔离式充气蓄能器 优先选择的液压油》.pdf

1、BRITISH STANDARD BS ISO 10946:1999 Hydraulic fluid power Gas-loaded accumulators with separator Selection of preferred hydraulic ports ICS 23.100.99BSISO 10946:1999 This British Standard, having been prepared under the directionof the Engineering SectorCommittee, was publishedunder the authority oft

2、he Standards Committee andcomesinto effect on 15 June 1999 BSI 02-2000 ISBN 0 580 32477 X National foreword This British Standard reproduces verbatim ISO 10946:1999 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Flu

3、id power systems and components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Euro

4、pean developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Stand

5、ards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible f

6、or their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theISO title page, pages ii to iv, pages1 to3 and abackcover. This standard has bee

7、n updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO 10946:1999 BSI 02-2000 i Contents Page National foreword Inside front cover Foreword iii T

8、ext of ISO 10946 1ii blankBSISO 10946:1999 ii BSI 02-2000 Contents Page Foreword iii Introduction 1 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 Dimensions 1 5 Identification statement 2 Figure 1 Thread connection possibilities 2 Table 1 Dimensions of ports for diaphragm type accum

9、ulators 3 Table 2 Dimensions of ports for bladder or piston type accumulators 3BSISO 10946:1999 BSI 02-2000 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards

10、is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organisations, governmental and non-governmental, in liaison with ISO, also take pa

11、rt in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardisation. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the

12、 technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10946 was prepared by Technical Committee ISO/TC 131, Fluid power systems.iv blankBSISO 10

13、946:1999 BSI 02-2000 1 Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Gas-loaded accumulators are components that are able to store and to return energy in accordance with the principle of the compressibi

14、lity of gases. Hydraulic fluid enters and leaves these accumulators through ports. 1 Scope This International Standard specifies the types and selection of hydraulic ports of gas-loaded accumulators with separator, which are used in hydraulic fluid power systems. 2 Normative references The following

15、 normative documents contain certain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this Internati

16、onal Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid Internat

17、ional Standards. ISO 1179-1:, Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports 1) . ISO 5596:, Hydraulic fluid power Gas-loaded accumulators with separator Range of pressures and volumes and chara

18、cteristic quantities 2) . ISO 5598:1985, Fluid power systems and components Vocabulary. ISO 6149-1:, Connections for fluid power and general use Ports and stud ends with ISO 261 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing 3) . ISO 6162-1:, Hydraulic fluid power Fla

19、nge connectors with split or one-piece flange clamps andmetric or inch screws Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to35 MPa (350 bar), DN 13 to DN 127 4) . ISO 6162-2:, Hydraulic fluid power Flange connectors with split or one-piece flange clamps andmetric or inch screw

20、s Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51 4) . ISO 6164-1:, Hydraulic fluid power One-piece square-flange connections Part 1: Four-screw square-flange connections, 25 MPa (250 bar) series, DN 10 to DN 63 5) . ISO 6164-2:, Hydraulic fluid

21、 power One-piece square-flange connections Part 2: Four-screw square-flange connections, 40 MPa (400 bar) series, DN 10 to DN 80 5) . ISO 6164-3:, Hydraulic fluid power One-piece square-flange connections Part 3: Four-screw square-flange connections, 50 MPa (500 bar) series, DN 12 to DN 50 5) . 3 Te

22、rms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 5598 and the following apply. 3.1 bladder type accumulator gas-loaded accumulator in which the liquid and gas are separated by a flexible bag or bladder that is normally retained at one end of

23、 the shell 3.2 diaphragm type accumulator gas-loaded accumulator in which the liquid and gas are separated by a flexible membrane that is normally retained at its largest diameter to the shell 3.3 piston type accumulator gas-loaded accumulator in which the liquid and gas are separated by a rigid sli

24、ding piston 4 Dimensions 4.1 General requirements For threaded ports, those specified in ISO 6149-1 shall be preferred. For flange ports, those specified in ISO 6162-1, ISO 6162-2, ISO 6164-1, ISO 6164-2 and ISO 6164-3 shall be preferred. The threaded ports specified in ISO 1179-1 are optional and m

25、ay be used for existing applications. 1) To be published. (Revision of ISO 1179:1981) 2) To be published. (Revision of ISO 5596:1982) 3) To be published. (Revision of ISO 6149-1:1993) 4) To be published. (Revision of ISO 6162:1994) 5) To be published. (Revision of ISO 6164:1994)BSISO 10946:1999 2 BS

26、I 02-2000 4.2 Thread connections Thread connection possibilities are illustrated in Figure 1, which shows ports, as indicated by the arrows. 4.3 Requirements for ports used with diaphragm type accumulators Ports used with diaphragm type accumulators shall be selected from those given in Table 1. 4.4

27、 Requirements for ports used with bladder or piston type accumulators Ports used with bladder or piston type accumulators shall be selected from those given in Table 2. 5 Identification statement (reference to this International Standard) Use the following statement in test reports, catalogues, and

28、sales literature when electing to comply with this International Standard: “Hydraulic ports for gas-loaded accumulators with separator selected in accordance with ISO10946:1999, Hydraulic fluid power Gas-loaded accumulators with separator Selection of preferred hydraulic ports.” Figure 1 Thread conn

29、ection possibilitiesBSISO 10946:1999 BSI 02-2000 3 Table 1 Dimensions of ports for diaphragm type accumulators Table 2 Dimensions of ports for bladder or piston type accumulators Preferred port in accordance with ISO 6149-1 M14 1,5 M18 1,5 M22 1,5 M27 2 Optional port in accordance with ISO1179-1 for

30、 existing applications G 1/4 G 3/8 G 1/2 G 3/4 Volume l u 0,4 0,4, u 1,6 1,6, u 6,3 NOTEShaded areas indicate preferred port sizes. Preferred threaded port in accordance with ISO6149-1 M14 1,5 M18 1,5 M22 1,5 M27 2 M33 2 M42 2 M48 2 M60 2 Optional threaded port in accordance with ISO1179-1 for exist

31、ing applications G 1/4 G 3/8 G 1/2 G 3/4 G 1 G 1 1/4 G 1 1/2 G 2 b Flange port ain accordance with ISO 6162 or ISO 6164, DN 13 19 25 32 38 Volume l u 0,4 0,4, u 1 1, u 10 10 NOTEShaded areas indicate preferred port sizes. a Flange port series shall be selected according to the allowable pressure of

32、the accumulator (p 4 ), i.e., the maximum permissible pressure for which the accumulator has been designed and/or qualified (see ISO 5596). b ISO 1179-1 does not specify this port for use in hydraulic applications.BS ISO 10946:1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitut

33、ion BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should m

34、ake sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee re

35、sponsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, interna

36、tional and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested

37、. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. C

38、ontact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002

39、. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval

40、 system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.

41、If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.