BS ISO 11090-1-2014 Test conditions for die sinking electro-discharge machines (die sinking EDM) Testing of the accuracy Single-column machines (cross-slide table type and fixed-ta.pdf

1、BSI Standards PublicationBS ISO 11090-1:2014Test conditions for die sinkingelectro-discharge machines (diesinking EDM) Testing of theaccuracyPart 1: Single-column machines (cross-slidetable type and fixed-table type)BS ISO 11090-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK

2、 implementation of ISO 11090-1:2014.It supersedes BS ISO 11090-1:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/1/2, Machine tools - Accuracy.A list of organizations represented on this committee can beobtained on request to its secretary.This

3、 publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 77144 6ICS 25.120.40Compliance with a British Standard cannot confer immu

4、nity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS ISO 11090-1:2014 ISO 2014Test conditions for die sinking electro-discharge machines (die sinkin

5、g EDM) Testing of the accuracy Part 1: Single-column machines (cross-slide table type and fixed-table type)Conditions dessai des machines dlectrorosion en plonge (EDM en plonge) Contrle de lexactitude Partie 1: Machines un montant ( bancs en croix et table fixe)INTERNATIONAL STANDARDISO11090-1Second

6、 edition2014-12-01Reference numberISO 11090-1:2014(E)BS ISO 11090-1:2014ISO 11090-1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any me

7、ans, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva

8、20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 11090-1:2014ISO 11090-1:2014(E)Contents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Terminology and designation of axes . 24.1 Cross-slid

9、e table type 24.2 Fixed table type 35 Preliminary remarks . 45.1 Measurement units 45.2 Reference to ISO 230-1 45.3 Machine levelling 45.4 Testing sequence . 45.5 Tests to be performed . 45.6 Measuring instruments . 55.7 Software compensation . 55.8 Minimum tolerance . 55.9 Machining test . 55.10 Po

10、sitioning tests and reference to ISO 230-2 . 56 Geometric tests 66.1 Linear axes of motion 66.2 Table 136.3 Head, quill and spindle 157 Positioning tests for numerically controlled axes 188 Machining test 21Annex A (informative) Equivalent terms in Dutch, German, Italian, Swedish, Persian, and Japan

11、ese 23Bibliography .25 ISO 2014 All rights reserved iiiBS ISO 11090-1:2014ISO 11090-1:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried

12、out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO

13、collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different ap

14、proval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the

15、 subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any

16、trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the

17、 Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is ISO/TC 39, Machine tools, Subcommittee SC 2, Test conditions for metal cutting machine tools.This second edition cancels and replaces the first edition (ISO 1

18、1090-1:1998), which has been technically revised.ISO 11090 consists of the following parts, under the general title Test conditions for die sinking electro-discharge machines (die sinking EDM) Testing of the accuracy: Part 1: Single-column machines (cross-slide table type and fixed table type) Part

19、2: Double-column machines (slide-head type)iv ISO 2014 All rights reservedBS ISO 11090-1:2014ISO 11090-1:2014(E)IntroductionThe purpose of this part of ISO 11090 is to standardize methods of testing normal accuracy and general-purpose die sinking electro-discharge machines (die sinking EDM).In this

20、part of ISO 11090, the tolerances for G1, G2, G3, G4, G5, G14, P1, P2, P3, and P4 have been changed from those in ISO 11090-1:1998. The following tests in ISO 11090-1:1998 are deleted due to the limited availability of the reference T-slot in typical machines in todays market: G9 (Checking of straig

21、htness of the reference T-slot or reference surface of the table) and G10 (Checking of parallelism between the reference T-slot or reference surface of the table and the x-axis motion). ISO 2014 All rights reserved vBS ISO 11090-1:2014BS ISO 11090-1:2014Test conditions for die sinking electro-discha

22、rge machines (die sinking EDM) Testing of the accuracy Part 1: Single-column machines (cross-slide table type and fixed-table type)1 ScopeThis part of ISO 11090 specifies, with reference to ISO 230-1 and ISO 230-2, geometric and machining tests and tests for checking accuracy and repeatability of nu

23、merically controlled positioning axes for normal accuracy and general-purpose die sinking electro-discharge machines (die sinking EDM). It also specifies the applicable tolerances corresponding to the above-mentioned tests.This part of ISO 11090 is also applicable to single-column machines of cross-

24、slide table type and fixed table type.This part of ISO 11090 deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.) or to the checking of its characteristics (such as

25、speeds, feeds, etc.), which should generally be checked before the testing of the accuracy.This part of ISO 11090 provides the terminology used for the principal components of the machine and the designation of the axes with reference to ISO 841:2001.NOTE In addition to the terms used in the officia

26、l ISO languages (English and French), Annex A of this part of ISO 11090 gives the equivalent terms in the Dutch, German, Italian, Swedish, Persian, and Japanese languages. These are published under the responsibility of the national member bodies for Netherlands (NEN), Germany (DIN), Italy (UNI), Sw

27、eden (SIS), Iran (ISIRI), and Japan (JISC). However, only the terms given in the official languages can be considered as ISO terms.2 Normative referencesThe following referenced documents, in whole or in part, are normatively referenced in this document and are indispensable for the application of t

28、his document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 230-1:2012, Test code for machine tools Part 1: Geometric accuracy of machines operating under no-load or quasi-static cond

29、itionsISO 230-2:2014, Test code for machine tools Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes3 Terms and definitionsFor the purposes of this document, the following terms and definitions applyINTERNATIONAL STANDARD ISO 11090-1:2014(E) ISO 2014 Al

30、l rights reserved 1BS ISO 11090-1:2014ISO 11090-1:2014(E)3.1electro-discharge machinesmachine tools for the removal of material in dielectric fluid by electro-discharges which are separated in time and randomly distributed in space between two electrically conductive electrodes (the tool electrode a

31、nd the workpiece electrode) and where the energy in the discharge is controlled3.2die sinking electro-discharge machinesmachine tools for the removal of material by electro-discharge machining through the application of a tool electrode whose geometry matches (defines) the desired shape of the workp

32、iece feature3.3wire electro-discharge machinesmachine tools for the removal of material by electro-discharge machining through the application of a wire electrode to produce prismatic and more complex shapes in a workpiece4 Terminology and designation of axes4.1 Cross-slide table typeSee Figure 1 an

33、d Table 1.+W+Z-X+Y1526789+C1034+Y+Z+XNOTE See keys in Table 1.Figure 1 Single-column machine with cross-slide tableTable 1 Keys for Figure 1Key English French1 bed banc2 ISO 2014 All rights reservedBS ISO 11090-1:2014ISO 11090-1:2014(E)Key English French2 column montant3 table (X-axis) table (axe X)

34、4 saddle (Y-axis) chariot transversal (axe Y)5 work tank rservoir de travail6 head (W-axis) tte de travail (axe W)7 quill (Z-axis) coulisse (axe Z)8 electrode platen porte-lectrode9 spindle (C-axis) broche (axe C)10 electrode electrode4.2 Fixed table typeSee Figure 2 and Table 2.+Z+X+Y1526789+C1134+

35、Y+Z+X+W10NOTE See keys in Table 2.Figure 2 Single-column machine with fixed tableTable 2 Keys for Figure 2Key English French1 bed banc2 column montant3 saddle (X-axis) chariot longitudinal (axe X)Table 1 (continued) ISO 2014 All rights reserved 3BS ISO 11090-1:2014ISO 11090-1:2014(E)Key English Fren

36、ch4 ram ( Y-axis) coulant (axe Y)5 table table6 work tank rservoir de travail7 head (W-axis) tte de travail (axe W)8 quill (Z-axis) coulisse (axe Z)9 electrode platen porte-lectrode10 spindle (C-axis) broche (axe C)11 electrode electrode5 Preliminary remarks5.1 Measurement unitsIn this part of ISO 1

37、1090, all linear dimensions, deviations, and corresponding tolerances are expressed in millimetres, angular dimensions are expressed in degrees, and angular deviations and the corresponding tolerances are expressed primarily in ratios, but in some cases, microradians or arcseconds can be used for cl

38、arification purposes. The following expression should be used for the conversion of angular deviations or tolerances:0 010 1000 10 10 10 26,/ = =rad (1)5.2 Reference to ISO 230-1For the application of this part of ISO 11090, reference shall be made to ISO 230-1 especially for the installation of the

39、 machine before testing, warming up of the spindle and other moving parts, the description of measuring methods, and recommended accuracy of testing equipment.In the “Observations” block of the tests described in Clauses 6, 7, and 8, the instructions are preceded by a reference to the corresponding

40、clause/subclause in ISO 230-1 in cases where the test concerned is in compliance with the specifications. Tolerances are given for each geometric test (see G1 to G12).5.3 Machine levellingPrior to conducting tests on a machine, the machine should be levelled according to the recommendations of the m

41、anufacturer/supplier (see ISO 230-1:2012, 6.1.2).5.4 Testing sequenceThe sequence in which the geometric tests are given in no way defines the practical order of testing. In order to make the mounting of instruments or gauging easier, the tests may be performed in any order.5.5 Tests to be performed

42、When testing a machine tool, it is not always necessary or possible to carry out all the tests given in this part of ISO 11090. When the tests are required for acceptance purposes, the choice of tests relating to the components and/or the properties of the machine of interest is at the discretion of

43、 the user, in agreement with the manufacturer/supplier. The tests to be used are to be clearly stated when ordering a machine tool. A mere reference to this part of ISO 11090 for the acceptance tests, without specifying the tests to be carried out and without agreement on the relevant expenses, cann

44、ot be considered as binding for any contracting parties.Table 2 (continued)4 ISO 2014 All rights reservedBS ISO 11090-1:2014ISO 11090-1:2014(E)5.6 Measuring instrumentsThe measuring instruments indicated in the tests described in Clauses 6 to 8 are examples only. Other instruments measuring the same

45、 quantities and having the same or smaller measurement uncertainty can be used.5.7 Software compensationWhen built-in software facilities are available for compensating geometric, positioning, contouring, and/or thermal deviations, their use during these tests shall be based on agreement between the

46、 manufacturer/supplier and the user with due consideration to the machine tools intended use.When the software compensation is used, this shall be stated in the test reports.It shall be noted that when software compensation is used, axes shall not be locked for test purposes.5.8 Minimum toleranceWhe

47、n the tolerance for a geometric test is established for a measuring length different from that given in this part of ISO 11090, the tolerance can be determined by means of the law of proportionality (see ISO 230-1:2012, 4.1.2). It shall be taken into consideration that the minimum value of tolerance

48、 is 0,005 mm.5.9 Machining testMachining test shall be made under finishing conditions.5.10 Positioning tests and reference to ISO 230-2Tests P1 to P4 are applied only to numerically controlled electro-discharge machines.To apply these tests, reference shall be made to ISO 230-2, especially for the

49、environmental conditions, warming up of the machine, measuring methods, evaluation, and interpretation of the results.Checking of the W-axis is not included because the W movement is used for adjusting the head position. When required, it shall be done in the same way as the checking of the Z-axis. ISO 2014 All rights reserved 5BS ISO 11090-1:2014ISO 11090-1:2014(E)6 Geometric tests6.1 Linear axes of motionObject G1Checking of straightness of the x-axis motion:a) in the horizontal XY plane (EYX);b)