BS ISO 11093-5-2016 Paper and board Testing of cores Determination of characteristics of concentric rotation《纸和纸板 纸芯测试 同心旋转的特性测定》.pdf

1、BSI Standards PublicationBS ISO 11093-5:2016Paper and board Testing ofcoresPart 5: Determination of characteristics ofconcentric rotationBS ISO 11093-5:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 11093-5:2016. It supersedes BS ISO 11093-5:2009 which is

2、 withdrawn.The UK participation in its preparation was entrusted to Technical Committee PAI/11, Methods of test for paper, board and pulps.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary

3、provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 90637 4 ICS 85.060; 85.080.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standa

4、rd was published under the authority of the Standards Policy and Strategy Committee on 29 February 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 11093-5:2016 ISO 2016Paper and board Testing of cores Part 5: Determination of characteristics of concentric rotati

5、onPapier et carton Essais des mandrins Partie 5: Dtermination des caractristiques de rotationINTERNATIONAL STANDARDISO11093-5Third edition2016-02-01Reference numberISO 11093-5:2016(E)BS ISO 11093-5:2016ISO 11093-5:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published

6、 in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission c

7、an be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 11093-5:2016ISO 11093-5:2016(E)Forewor

8、d iv1 Scope . 12 Normative references 13 Principles . 13.1 Determination of roundness deviation (fR) by three-point measurement . 13.2 Determination of the straightness deviation (fS) by five-point measurement 14 Apparatus . 15 Preparation of test pieces . 25.1 Sampling . 25.2 Test pieces . 25.3 Con

9、ditioning of test pieces . 26 Measuring procedure 36.1 General . 36.2 Positioning of the support . 36.3 Measuring of roundness deviation 36.4 Measuring of straightness deviation 36.4.1 Straightness deviation. 36.4.2 Precision of the measurement system 37 Calculation 48 Test report . 4 ISO 2016 All r

10、ights reserved iiiContents PageBS ISO 11093-5:2016ISO 11093-5:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technica

11、l committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wit

12、h the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed f

13、or the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent right

14、s. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this

15、document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to T

16、rade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 6, Paper, board and pulps.This third edition cancels and replaces the second edition (ISO 11093-5:2009), of which it constitutes a minor revision. It also incorporates the Tech

17、nical Corrigendum ISO 11093-5:2009/Cor.1:2010.ISO 11093 consists of the following parts, under the general title Paper and board Testing of cores: Part 1: Sampling Part 2: Conditioning of test samples Part 3: Determination of moisture content using the oven drying method Part 4: Measurement of dimen

18、sions Part 5: Determination of characteristics of concentric rotation Part 6: Determination of bending strength by the three-point method Part 7: Determination of flexural modulus by the three-point method Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis

19、 Part 9: Determination of flat crush resistanceiv ISO 2016 All rights reservedBS ISO 11093-5:2016INTERNATIONAL STANDARD ISO 11093-5:2016(E)Paper and board Testing of cores Part 5: Determination of characteristics of concentric rotation1 ScopeThis part of ISO 11093 specifies a method for determining

20、the characteristics of concentric rotation of cylindrical board cores which meet the following criteria: minimum wall thickness: 5 mm; minimum external diameter: 60 mm; maximum sample length: 3 200 mm.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in t

21、his document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 110931, Paper and board Testing of cores Part 1: SamplingISO 110932, Paper and bo

22、ard Testing of cores Part 2: Conditioning of test samples3 Principles3.1 Determination of roundness deviation (fR) by three-point measurementMeasurement between three points in a plane perpendicular to the core axis where two points are fixed in predetermined positions and the third moves in the dir

23、ection of the measurement.3.2 Determination of the straightness deviation (fS) by five-point measurementMeasurement between five points in planes perpendicular to the core axis where four measuring points are fixed in pairs in predetermined positions in two planes perpendicular to the core axis, and

24、 the fifth in a central plane perpendicular to the core axis moves in the direction of the measurement.4 ApparatusThe apparatus, shown in Figure 1, consists of two supports (2), a rack (1), and two measuring heads (4 and 5). Each support consists of two free rotating support rollers mounted side by

25、side (3) where the distance between the two can be adjusted. The diameter of each roller shall be (85 1) mm and the width shall be (19 1) mm. For example, a 6209 roller bearing can be used.Each measuring head consists of a flat foot with a diameter of 10 mm, a rod which transmits the vertical moveme

26、nt of the foot to a dial gauge and a dial gauge graduated in 0,01 mm, accurate to at least 0,005 mm. The load exerted by each measuring foot on the test piece is approximately 1,2 N. One of the measuring heads (4) is fixed directly above the mid-point between one pair of support rollers. The other m

27、easuring head (5) is moveable parallel to the rack. ISO 2016 All rights reserved 1BS ISO 11093-5:2016ISO 11093-5:2016(E)123456Key1 rack2 supports3 support rollers4 measuring head5 measuring head, moveable6 test pieceFigure 1 Schematic representation of the apparatus5 Preparation of test pieces5.1 Sa

28、mplingSampling shall be carried out in accordance with ISO 11093-1.5.2 Test piecesFor cores less than 3 200 mm long, the complete undamaged core shall be tested.For cores more than 3 200 mm long, a test piece from 1 200 mm to 3 200 mm long shall be cut. If there is an obvious difference in warpage b

29、etween various positions of the long core, the test piece shall be taken from where the warpage is greatest.5.3 Conditioning of test piecesThe test pieces shall be conditioned in accordance with ISO 11093-2.2 ISO 2016 All rights reservedBS ISO 11093-5:2016ISO 11093-5:2016(E)6 Measuring procedure6.1

30、GeneralMeasuring shall be carried out in a standard atmosphere identical to that used for the conditioning (see 5.3). The measuring heads shall not produce any measurable deformation of the test piece during measuring.6.2 Positioning of the supportAdjust the distance between the two support rollers

31、within each pair so that the tangents to the lines of the support of the core form an angle of 120 5. Adjust the distance between the inner faces of the two pairs of support rollers to the core length less (200 10) mm. This is the test length. Position the core centrally on the support rollers.6.3 M

32、easuring of roundness deviationPlace the foot of the fixed measuring head in contact with the core so that it is centrally located with respect to the core axis and the line between the support-roller pair to an accuracy of 1 mm. Rotate the core through 360 and record the highest and lowest readings

33、 of the gauge to an accuracy of 0,01 mm. The difference between the two readings is the individual value for the roundness deviation ( fR), expressed in millimetres.6.4 Measuring of straightness deviation6.4.1 Straightness deviationPlace the foot of the moveable measuring head in contact with the co

34、re so that it is centrally located with respect to the core axis at a point half-way between the two support-roller pairs. The measuring head placed at the half-way point is located with an accuracy of 1 mm. Rotate the core through 360 and record the highest and lowest readings of the gauge to an ac

35、curacy of 0,01 mm. Record the difference between the two readings. The straightness deviation ( fS) is half of this measured difference (x), determined with an accuracy of 0,01 mm, as given in Formula (1):fxS=2(1)wherefSis the straightness deviation, in mm;x is the measured difference, in mm.6.4.2 P

36、recision of the measurement systemProvided that the rack has the stiffness needed, the precision of the measurement system is sufficient for cores which have a straightness deviation 0,3 mm/m. ISO 2016 All rights reserved 3BS ISO 11093-5:2016ISO 11093-5:2016(E)To obtain comparable values for paper c

37、ores of different (support) lengths, the following conversion to millimetres per metre (mm/m), as given in Formula (2), shall be made:fflSS=1000(2)wherefSis the straightness deviation, in mm/m;fSis the straightness deviation, in mm see Formula (1) in 6.4.1;l is the distance between supports (inner m

38、easurement), in mm.7 CalculationCalculate the mean and standard deviation for the roundness deviation and straightness deviation to the nearest 0,01 mm.8 Test reportThe test report shall include the following information:a) reference to this part of ISO 11093, i.e. ISO 110935;b) type and designation

39、 of the cores tested;c) place and date of sampling;d) place and date of test;e) number of test pieces;f) core length;g) test length;h) mean and standard deviation of the roundness deviation ( fR);i) mean and standard deviation of the straightness deviation ( fS);j) date and signature;k) any deviatio

40、n from this part of ISO 11093 that might have affected the results.4 ISO 2016 All rights reservedBS ISO 11093-5:2016BS ISO 11093-5:2016ISO 11093-5:2016(E) ISO 2016 All rights reservedICS 85.060Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing B

41、ritish Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London

42、 W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our op

43、en consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or con

44、tacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign

45、 standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Onl

46、ine (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase

47、 price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about beco

48、ming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure you

49、r documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll t