BS ISO 1132-2-2002 Rolling bearings Tolerances Measuring and gauging principles and methods《滚动轴承 公差 测量和校验原理和方法》.pdf

1、BRITISH STANDARD BS ISO 1132-2:2001 Rolling bearings Tolerances Part 2: Measuring and gauging principles and methods ICS 21.100.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 1132-2:2001 This British Standard, having been prepared under the direction of the Engineeri

2、ng Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 26 April 2002 BSI 26 April 2002 ISBN 0 580 39485 9 National foreword This British Standard reproduces verbatim ISO 1132-2:2001and implements it as the UK national standard. Th

3、e UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international

4、 or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all

5、the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European comm

6、ittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii t

7、o iv, pages 1 to 48, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsReference number ISO/FDIS 1132-2:2001(E) INTERNATIONAL STANDARD ISO 1132-2 First editio

8、n 2001-09-01 Rolling bearings Tolerances Part 2: Measuring and gauging principles and methods Roulements Tolrances Partie 2: Principes et mthodes de mesurage et de vrification par calibreii ISO 1132-2:2001(E)iii Contents Page Foreword.iv 1 Scope 1 2 Normative references 1 3 Terms and definitions .2

9、4 Symbols 2 5 General conditions 4 6 Measuring and gauging principles and methods.7 7 Principles of measuring bore diameter .8 8 Principles of measuring outside diameter 14 9 Principles of measuring width and height 17 10 Principles of measuring ring and washer chamfer dimension .24 11 Principles of

10、 measuring raceway parallelism.26 12 Principles of measuring surface perpendicularity.28 13 Principles of measuring thickness variation 32 14 Principles of measuring radial runout.37 15 Principles of measuring axial runout 42 16 Principles of measuring radial clearance45 Annex A (normative) Cross-re

11、ference to clauses in ISO 1132-147ISO 1132-2:2001(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees

12、. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Intern

13、ational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodie

14、s for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 1132 may be the subject of patent rights. ISO shall not be held responsible for identifyi

15、ng any or all such patent rights. International Standard ISO 1132-2 was prepared by Technical Committee ISO/TC 4, Rolling bearings. This first edition of ISO 1132-2 cancels and replaces ISO/TR 9274:1991, in the form of a technical revision thereof. ISO 1132 consists of the following parts, under the general title Rolling bearings Tolerances: Part 1: Terms and definitions Part 2: Measuring and gauging principles and methods Annex A forms a normative part of this part of ISO 1132.