BS ISO 11379-2009 Textile floor coverings - Laboratory cleaning procedure using spray extraction《铺地织物 采用喷雾提取法的实验室清洁程序》.pdf

1、BS ISO11379:2009ICS 59.080.60NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTextile floor coverings Laboratory cleaningprocedure using sprayextractionThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June20

2、09. BSI 2009ISBN 978 0 580 56944 9Amendments/corrigenda issued since publicationDate CommentsBS ISO 11379:2009National forewordThis British Standard is the UK implementation of ISO 11379:2009. Itsupersedes BS ISO 11379:1997 which is withdrawn.The UK participation in its preparation was entrusted to

3、TechnicalCommittee PRI/3, Textile floor coverings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with

4、 a British Standard cannot confer immunityfrom legal obligations.BS ISO 11379:2009Reference numberISO 11379:2009(E)ISO 2009INTERNATIONAL STANDARD ISO11379Second edition2009-02-01Textile floor coverings Laboratory cleaning procedure using spray extraction Revtements de sol textiles Mthode de nettoyag

5、e en laboratoire par injection-extraction BS ISO 11379:2009ISO 11379:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and

6、 installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software

7、 products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is fo

8、und, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mi

9、crofilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO

10、 2009 All rights reservedBS ISO 11379:2009ISO 11379:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried

11、out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO

12、collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Internationa

13、l Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the eleme

14、nts of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11379 was prepared by Technical Committee ISO/TC 219, Floor coverings. This second edition cancels and replaces the first edition (ISO 11379:1997), which has

15、 been technically revised. BS ISO 11379:2009BS ISO 11379:2009INTERNATIONAL STANDARD ISO 11379:2009(E) ISO 2009 All rights reserved 1Textile floor coverings Laboratory cleaning procedure using spray extraction 1 Scope This International Standard describes a laboratory-scale textile-floor-covering cle

16、aning procedure using a spray-extraction technique. This International Standard is applicable to all kinds of textile floor coverings, both machine-made and hand-made. NOTE Depending on the characteristic under investigation, test specimens subjected to this cleaning procedure can be evaluated for m

17、any properties, e.g. ease of soil (dirt) removal, changes in appearance, effects of cleaning materials and durability of floor covering finishes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition c

18、ited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 139, Textiles Standard atmospheres for conditioning and testing ISO 1957, Machine-made textile floor coverings Selection and cutting of specimens for physical tests 3 Principle

19、 Test specimens of textile floor coverings are treated in a controlled manner with a spray-extraction cleaning machine. 4 Apparatus and materials 4.1 Spray-extraction cleaning machine, capable of applying (3,75 0,25) l/m2of cleaning solution to the surface when the cleaner wand is moved across the s

20、urface at a rate of (40 5) mm/s. NOTE This may be achieved by using a machine with a wand width of (100 5) mm and an application rate of (0,9 0,1) l/min or by using a machine with a wand width of (200 10) mm and an application rate of (1,8 0,2) l/min. An antifoam agent may be used in the waste tank

21、of the spray-extraction machine but shall not be used in the delivery tank. 4.2 Suitable base, e.g. bench, table top or floor. 4.3 Floor-covering adhesive or pressure-sensitive adhesive tape. 4.4 Suction-only cleaner, canister-type, giving an air flow of (25 5) l/s through the suction-only nozzle wi

22、th a suction surface of (125 25) mm (15 2,5) mm. 4.5 Cleaning solution, prepared according to the manufacturers instructions. A specific cleaning agent should be advised when using this test method to evaluate whether a surface treatment was applied to the textile floor covering; the choice of the s

23、pecific cleaning agent is dependent on the nature of the surface treatment or intended subsequent test procedure. BS ISO 11379:2009ISO 11379:2009(E) 2 ISO 2009 All rights reserved5 Conditioning Condition the test specimens in one of the standard atmospheres described in ISO 139 for a minimum of 24 h

24、. 6 Preparation of test specimens Sample and select the test specimens in accordance with ISO 1957. Cut a test specimen of suitable dimensions from each sample, e.g. (200 300) mm, with the longer side in the manufacturing direction as shown in Figure 1. Dimensions in millimetres Key 1 surround of te

25、xtile floor covering 2 test specimen Figure 1 Example of dimensions of test specimen and mounting arrangement Mount the test specimen on a suitable base (4.2) using a floor-covering adhesive or pressure-sensitive adhesive tape (4.3). Surround the test specimen with a material of comparable construct

26、ion and thickness and of dimensions at least 100 mm greater than those of the test specimen secured to the base using the floor-covering adhesive or pressure-sensitive adhesive tape (4.3) (see Figure 1). Ensure that this material is colourfast to prevent bleeding into the test specimen. NOTE In some

27、 cases, the test specimen will be of predetermined dimensions, as it will have been used for other procedures, e.g. soiling, and the mounting arrangements will have to be adjusted accordingly. BS ISO 11379:2009ISO 11379:2009(E) ISO 2009 All rights reserved 37 Procedure 7.1 Use the suction-only clean

28、er (4.4) to clean the test specimens, using two double strokes, i.e. twice backwards and twice forwards, in order to give all parts of all specimens equal treatment, as follows. The first two double strokes shall be made with the vacuum cleaner suction slot approximately 50 % on the buffer textile f

29、loor covering and 50 % over the test area. Each subsequent series of strokes is made parallel to the first series with 50 % overlap, ending when the buffer strip at the other side is included in the overlap. 7.2 Prepare the cleaning solution (4.5). Pour the cleaning solution into the spray-extractio

30、n cleaning machine (4.1). Attach the cleaner wand and run the machine prior to cleaning to obtain stable conditions, including temperature, at the point of delivery. 7.3 Spray and extract the test specimen by drawing the cleaner wand at a speed of (40 5) mm/s, necessary to obtain the required applic

31、ation per unit area (see 4.1), in the length direction both with and against the pile lay. For the first stroke, position the cleaner wand approximately 50 % over the surround of textile floor covering and 50 % over the test specimen. For each subsequent stroke, allow 50 % overlap per stroke, finall

32、y ending when the opposite side of the surround of textile floor covering is included in the overlap. Do not use a scrubbing action. 7.4 Turn the test specimen through 180 and repeat the process described in 7.3. 7.5 Dry the test specimen to approximately constant mass and then condition in the stan

33、dard atmosphere (see Clause 5) for a minimum of 24 h, or proceed to the conditioning process required by any subsequent test procedure. 7.6 Suction clean the test specimen as described in 7.1 with the last stroke in the direction of the pile lay. 8 Test report The test report shall include the follo

34、wing information: a) a reference to this International Standard: ISO 11379:2008; b) identification of the textile floor covering; c) description of the spray-extraction machine used; d) conditioning atmosphere used; e) identification and concentration of the cleaning product; f) application rate and

35、 temperature at point of delivery of the cleaning solution; g) date of test; h) reason for carrying out the procedure. BS ISO 11379:2009ISO 11379:2009(E) ICS 59.080.60 Price based on 3 pages ISO 2009 All rights reserved BS ISO 11379:2009This page has been intentionally left blank BS ISO11379:2009BSI

36、 GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is in

37、corporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone

38、finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service call

39、ed PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy direct

40、ly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of

41、information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44

42、 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: In

43、formation regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the internation

44、al standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not

45、preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: