BS ISO 12151-3-2010 Connections for hydraulic fluid power and general use - Hose fittings - Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends《液压传动和通用连接件 软管接头 带ISO 6162-1或ISO .pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 12151-3:2010Connections for hydraulic fluidpower and general use HosefittingsPart 3: Hose fittings with ISO 6162-1 or ISO6162-2 flange endsBS ISO 12151-3:2010 BRITISH STAN

2、DARDNational forewordThis British Standard is the UK implementation of ISO 12151-3:2010.It supersedes BS ISO 12151-3:1999 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/4, Connectors and associated components.A list of organizations represente

3、d on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 58531 9ICS 23.040.70; 23.100.40Compliance with a British Standard cannot con

4、fer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2010Amendments issued since publicationDate Text affectedBS ISO 12151-3:2010Reference numberISO 12151-3:2010(E)ISO 2010INTERNATIONAL STANDARD ISO12151-3

5、Second edition2010-06-15Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends Raccordements pour transmissions hydrauliques et applications gnrales Raccords de flexible Partie 3: Raccords de flexible avec brides conformes

6、lISO 6162-1 ou lISO 6162-2 BS ISO 12151-3:2010ISO 12151-3:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed

7、on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products u

8、sed to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please

9、 inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, wi

10、thout permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All r

11、ights reservedBS ISO 12151-3:2010ISO 12151-3:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references2 3 Terms and definitions .2 4 Performance requirements.2 5 Designation of hose fittings .2 6 Design.3 7 Manufacture .3 8 Procurement informati

12、on .4 9 Marking.4 10 Identification statement (reference to this part of ISO 12151) .4 Bibliography12 BS ISO 12151-3:2010ISO 12151-3:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me

13、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme

14、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Dire

15、ctives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bod

16、ies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12151-3 was prepared by Technical Committee ISO/TC 131, Fluid power systems,

17、Subcommittee SC 4, Connectors and similar products and components. This second edition cancels and replaces the first edition (ISO 12151-3:1999), which has been technically revised. ISO 12151 consists of the following parts, under the general title Connections for hydraulic fluid power and general u

18、se Hose fittings: Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Part 2: Hose fittings with ISO 8434-1 and 8434-4 24 degree cone connector ends with O-rings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends Part 4: Hose fittings with ISO 6149 metric stud ends Part 5: Hose

19、fittings with ISO 8434-2 37 degree flared ends Part 6: Hose fittings with ISO 8434-6 60 degree cone ends BS ISO 12151-3:2010ISO 12151-3:2010(E) ISO 2010 All rights reserved vIntroduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an e

20、nclosed circuit. In general applications, the fluid can be conveyed under pressure. Components are connected through their ports by stud ends on fluid conductor connectors to tubes/pipes or to hose fittings and hoses. BS ISO 12151-3:2010BS ISO 12151-3:2010INTERNATIONAL STANDARD ISO 12151-3:2010(E) I

21、SO 2010 All rights reserved 1Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends 1 Scope This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of flange hose fittings, m

22、ade of carbon steel, for nominal hose inside diameters of 12,5 mm to 51 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162-1 and ISO 6162-2. NOTE 1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user. NOTE 2

23、For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22/SC 2, Road vehicles), see ISO 4038, ISO 4039-1 and ISO 4039-2. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose that

24、 meets the requirements of the respective hose standards and in general applications with suitable hoses. Key 1 hose fitting 2 port, flanged head and clamp per ISO 6162-1 or ISO 6162-2 3 O-ring seal Figure 1 Typical example of hose fitting connection with ISO 6162-1 or ISO 6162-2 flange end BS ISO 1

25、2151-3:2010ISO 12151-3:2010(E) 2 ISO 2010 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

26、including any amendments) applies. ISO 4397, Fluid power systems and components Connectors and associated components Nominal outside diameters of tubes and nominal inside diameters of hoses ISO 5598, Fluid power systems and components Vocabulary ISO 6162-1, Hydraulic fluid power Flange connectors wi

27、th split or one-piece flange clamps and metric or inch screws Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 ISO 6162-2, Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws Part 2: Flange con

28、nectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51 ISO 6605, Hydraulic fluid power Hoses and hose assemblies Test methods ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests ISO 19879, Metallic tube connections for fluid power and general use Test m

29、ethods for hydraulic fluid power connections 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Performance requirements 4.1 Hose assemblies shall meet the performance requirements specified in the appropriate hose specification without le

30、akage or failure. 4.2 The working pressure of the hose assembly shall be the lower of the pressures given for its flange style (pressure series) and size in ISO 6162-1 or ISO 6162-2, and in the relevant hose specification. 4.3 The hose-fitting portion of a hose assembly shall be tested in accordance

31、 with ISO 19879, and the complete hose assembly shall be tested in accordance with ISO 6605. 5 Designation of hose fittings 5.1 Hose fittings shall be designated by an alphanumeric code to facilitate ordering. They shall be designated by the words “Hose fitting”, followed by a space, followed by “IS

32、O 12151-3”, followed by a spaced hyphen, then the shape symbol (see 5.2), followed by another spaced hyphen, the style letter L for 2,5 MPa to 35 MPa (25 bar to 350 bar) flanges or the style letter S for 40 MPa (400 bar) flanges in accordance with ISO 6162-1 or ISO 6162-2, followed by the flange siz

33、e from ISO 6162-1 or ISO 6162-2, a multiplication symbol () and the hose size (nominal hose inside diameter in accordance with ISO 4397). EXAMPLE A 45 elbow hose fitting, with a medium drop length (E45M) with a 40 MPa (400 bar) flanged head (S) 32 mm nominal flange size and 31,5 nominal ID hose, is

34、designated as follows: Hose fitting ISO 12151-3 - E45M - S32 31,5 5.2 The letter symbols as given in Table 1 shall be used. BS ISO 12151-3:2010ISO 12151-3:2010(E) ISO 2010 All rights reserved 3Table 1 Letter symbols used in the designation of hose fittings Connection end type Symbol 2,5 MPa to 35 MP

35、a (25 bar to 350 bar) L Style 40 MPa (400 bar) S Straight S 45 elbow, short E45S 45 elbow, medium E45M 90 elbow, short ES Shape 90 elbow, medium EM 22,5 elbow, medium E22M 30 elbow, short E30S 30 elbow, medium E30M 60 elbow, short E60S 60 elbow, medium E60M 67,5 elbow, short E67S Deprecated fitting

36、angles 67,5 elbow, medium E67M 6 Design 6.1 Hose fitting dimensions shown in Figures 2 to 8 shall conform to those given in Tables 2 to 8 and to the relevant dimensions in ISO 6162-1 or ISO 6162-2. 6.2 Angular tolerances on axes of ends of elbows shall be 3 for all sizes. 6.3 Details of contour shal

37、l be as chosen by the manufacturer, provided that the dimensions given in Tables 2 to 8 are maintained. 7 Manufacture 7.1 Construction Hose fittings may be made by forging or cold forming, machined from barstock or manufactured from multiple components. 7.2 Workmanship Workmanship shall conform to t

38、he best commercial practice to produce high quality hose fittings. Hose fittings shall be free from visual contaminants, all hanging burrs, loose scale and slivers that can be dislodged in use, and any other defects that can affect the functioning of the parts. All machined surfaces shall have a sur

39、face roughness value of Ra u 6,3 m, except where otherwise specified. 7.3 Finish The external surface and threads of all carbon steel parts shall be plated or coated with a suitable material that passes a 72 h neutral salt spray test in accordance with ISO 9227, unless otherwise agreed upon by the B

40、S ISO 12151-3:2010ISO 12151-3:2010(E) 4 ISO 2010 All rights reservedmanufacturer and the user. Any appearance of red rust during the salt spray test on any area, except those noted below, shall be considered failure: all internal fluid passages; edges, such as hex points, serrations and crests of th

41、reads, where there can be mechanical deformation of the plating or coating typical of mass-produced parts or shipping effects; areas where there is mechanical deformation of the plating or coating caused by crimping, flaring, bending and other post-plate metal forming operations; areas where the par

42、ts are suspended or affixed in the test chamber where condensate can accumulate. Internal fluid passages shall be protected from corrosion during storage. NOTE Cadmium plating is deprecated due to environmental concerns. Changes in plating can affect assembly torques and require requalification, whe

43、n applicable. 7.4 Fitting protection By a method agreed between the supplier and purchaser, the face of the flange hose fittings shall be protected by the manufacturer from nicks and scratches that can be detrimental to the functioning of the hose fitting. Passages shall be securely covered to preve

44、nt the entrance of dirt or other contaminants. Covers that contribute to contamination shall not be used. 8 Procurement information The following minimum information should be supplied by the purchaser when making an inquiry or placing an order: description of hose fitting using designation in accor

45、dance with Clause 5; material of hose fitting if other than carbon steel; hose type and size; fluid being conveyed; working pressure; working temperature (ambient and of the fluid). 9 Marking Hose fittings shall be permanently marked with the manufacturers name or trademark. 10 Identification statem

46、ent (reference to this part of ISO 12151) It is strongly recommended to manufacturers who have chosen to conform to this part of ISO 12151 that the following statement be used in test reports, catalogues and sales literature: “Flange hose fittings conform to ISO 12151-3, Connections for hydraulic fl

47、uid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends.” BS ISO 12151-3:2010ISO 12151-3:2010(E) ISO 2010 All rights reserved 5NOTE 1 Connection details and O-rings in accordance with ISO 6162-1 or ISO 6162-2. NOTE 2 Method of attachment of hose fittin

48、g to hose is optional. Figure 2 Straight flange hose fittings (S) Table 2 Dimensions of straight flange hose fittings (S) Dimensions in millimetres d10,25 Hose fitting size S-L S-S Nominal flange size Nominal hose inside diameterd2d3a min. L1bmax. 13 12,5 30,2 31,8 13 12,5 8 100 19 12,5 38,1 41,3 19

49、 12,5 8 120 19 19 38,1 41,3 19 19 14 140 25 19 44,45 47,6 25 19 14 150 25 25 44,45 47,6 25 25 19 150 32 25 50,8 54 32 25 19 163 32 31,5 50,8 54 32 31,5 25 175 38 31,5 60,35 63,5 38 31,5 25 182 38 38 60,35 63,5 38 38 31 200 51 38 71,4 79,4 51 38 31 220 51 51 71,4 79,4 51 51 42 240 aMinimum diameter at any point through the hose fitting prior to assembly to the hose. The diameter after assembly shall not be less than 0,