1、BSI Standards PublicationBS ISO 12164-4:2014Hollow taper interface withflange contact surfacePart 4: Dimensions of receivers forstationary toolsBS ISO 12164-4:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12164-4:2014.It supersedes BS ISO 12164-4:2008 wh
2、ich is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the n
3、ecessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83598 8ICS 25.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard w
4、as published under the authority of theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS ISO 12164-4:2014 ISO 2014Hollow taper interface with flange contact surface Part 4: Dimensions of receivers for stationary toolsInterfaces cne cr
5、eux-face Partie 4: Dimensions des nez de broches pour outils non rotatifsINTERNATIONAL STANDARDISO12164-4Second edition2014-12-15Reference numberISO 12164-4:2014(E)BS ISO 12164-4:2014ISO 12164-4:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless ot
6、herwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the addres
7、s below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 12164-4:2014ISO 12164-4:2014(E) ISO 2014 All rights reserved iiiContents Pa
8、geForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2 Receiver for hollow taper shank, type T . 14 Design Hole for manual clamping . 35 Designation 3Annex A (informative) Recommendations for use and application . 5Bibliography 6BS ISO 12164-4:2014ISO 12164-4:2014(E)Forew
9、ordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic
10、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el
11、ectrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was
12、 drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such pate
13、nt rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not
14、constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationTh
15、e committee responsible for this document is ISO/TC 29, Small tools.This second edition cancels and replaces the first edition (ISO 12164-4:2008), Figure 1 of which has been technically revised.ISO 12164 consists of the following parts, under the general title Hollow taper interface with flange cont
16、act surface: Part 1: Shanks Dimensions Part 2: Receivers Dimensions Part 3: Dimensions of shanks for stationary tools Part 4: Dimensions of receivers for stationary toolsiv ISO 2014 All rights reservedBS ISO 12164-4:2014INTERNATIONAL STANDARD ISO 12164-4:2014(E)Hollow taper interface with flange con
17、tact surface Part 4: Dimensions of receivers for stationary tools1 ScopeThis part of ISO 12164 specifies dimensions for receivers with taper and flange contact surfaces for hollow taper shanks in accordance with ISO 12164-3 to be applied to machine tools (e.g. turning machines, turning-mill machines
18、). A range of sizes is specified.This part of ISO 12164 specifies the receiver of type T. It is for automatic tool exchange and manual clamping, which is achieved via holes in both the receiver and the tool shank.The torque is transmitted via the tail end of the shank through keys as well as frictio
19、n.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amen
20、dments) applies.ISO 1101, Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-outISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 3040, Geometrical product sp
21、ecifications (GPS) Dimensioning and tolerancing Cones3 Dimensions3.1 GeneralDimensions of receivers for hollow taper shanks with flange contact surface for stationary tools, type T, are specified in Figure 1, Table 1, and Annex A. Details not specified in Figures 1 shall be chosen expediently. Toler
22、ancing of form, orientation, location, and run-out is in accordance with ISO 1101. Dimensioning and tolerancing of cones are in accordance with ISO 3040. Tolerances not specified shall be of tolerance class m in accordance with ISO 2768-1.3.2 Receiver for hollow taper shank, type TThe dimensions of
23、receiver for hollow taper shanks, type T, shall be in conformance with Figure 1 and Table 1. ISO 2014 All rights reserved 1BS ISO 12164-4:2014ISO 12164-4:2014(E)Dimensions in millimetres Surface roughness values in micrometresKey1 cutting edgeb2 tenonc3 hole for manual clampingdaWhen tenons are inse
24、rted, the taper hole may be conical over the total length l1.bPosition of the cutting edge for right-hand tools with single cutting edged.cTenon alternative integrated or inserted.dInside edge min. 0,5 mm 45 chamfer.Figure 1 Dimensions of receivers2 ISO 2014 All rights reservedBS ISO 12164-4:2014ISO
25、 12164-4:2014(E)Table 1 DimensionsDimensions in millimetresNominal size 32 40 50 63 80 100 125 160b10,05 6,8 7,8 10,3 12,3 15,8 19,78 24,78 29,78b26,92 7,92 10,41 12,41 15,91 19,89 24,89 29,89tol.0 0250, 0030,d1min. 32 40 50 63 80 100 125 160d223,998 29,998 37,998 47,998 59,997 74,997 94,996 119,995
26、d3a17 21 26 34 42 53 67 85d4b001+ ,23,28 29,06 36,85 46,53 58,1 72,6 92,05 116,1d5002+ ,23,8 29,6 37,5 47,2 58,8 73,4 93 118d6Hole diameter to be chosen by the manufacturerl1b002+ ,16,5 20,5 25,5 33 41 51 64 81l23,2 4 5 6,3 8 10 12,5 16l3002+ ,11,4 14,4 17,9 22,4 28,4 35,4 44,4 57,4l4002+ ,13,4 16,9
27、 20,9 26,4 32,4 40,4 51,4 64,4l50,8 0,8 1 1 1,5 1,5 2 2l6001+ ,1 1 1,5 1,5 2 2 2,5 2,5l70,1 2 2 2 2,5 3 3 4 4l80,1 5 6 7,5 9 12 15 r1c0050,1,5 2 2,5 3 4 5 6 8t 0,001 5 0,001 5 0,002 0,002 0,002 5 0,003 0,003 5 0,003 5aDepending on the clamping system.bSee note ato Figure 1.cr1tangent to b1or b2and d
28、4.4 Design Hole for manual clampingDesign without hole for manual clamping is standard.Design with hole for manual clamping is optional.5 DesignationA receiver for hollow taper shank (HSK) in accordance with this part of ISO 12164 shall be designated by the following:a) “Receiver for hollow taper sh
29、ank”; ISO 2014 All rights reserved 3BS ISO 12164-4:2014ISO 12164-4:2014(E)b) reference to this part of ISO 12164, i.e. ISO 12164-4;c) “HSK”;d) type: T for stationary tools;e) nominal size, in millimetres.EXAMPLE A receiver for hollow taper shank with flange contact surface (HSK) for stationary tools
30、 (type T) with nominal size 50 mm is designated as follows:Receiver for hollow taper shank ISO 12164-4-HSK-T 504 ISO 2014 All rights reservedBS ISO 12164-4:2014ISO 12164-4:2014(E)Annex A (informative) Recommendations for use and applicationA.1 Clamping systemThe clamping system should be specified b
31、y the manufacturer of the receiver or machine tool spindle. The system should provide sufficient clamping force to ensure contact of the shank flange with the receiver face, as well as seating of the taper by elastic deformation. The torque transmitting capacity of the interface is substantially det
32、ermined by the size of the clamping force.A.2 Clamping forcesThe recommended clamping forces are shown in Table A.1.The clamping forces are only applied to the hollow shanks for stationary tools (type T).Table A.1Nominal size, mm 32 40 50 63 80 100 125 160Clamping force, kN 5 8 14 24 37 55 86 150Low
33、er clamping forces can be sufficient when operational loads are low (e.g. cutting and feed forces in finish machining). Conversely, higher clamping forces can be required when high operational loads are encountered (e.g. cutting and feed forces in heavy machining).A.3 Information about speeds and to
34、rqueThe manufacturer should provide information regarding permissible speeds and torque transmitting capacities. ISO 2014 All rights reserved 5BS ISO 12164-4:2014ISO 12164-4:2014(E)Bibliography1 ISO 12164-3, Hollow taper interface with flange contact surface Part 3: Dimensions of shanks for stationa
35、ry tools6 ISO 2014 All rights reservedBS ISO 12164-4:2014BS ISO 12164-4:2014ISO 12164-4:2014(E) ISO 2014 All rights reservedICS 25.060.20Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publication
36、s, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry,
37、government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and
38、across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.B
39、uying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organization
40、s, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 Brit
41、ish and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscriptio
42、n format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of member
43、ship, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, ema
44、il .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowle
45、dge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formall
46、y licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without
47、prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1