1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 13007-1:2010Ceramic tiles Grouts andadhesivesPart 1: Terms, definitions and specificationsfor adhesivesBS ISO 13007-1:2010 BRITISH STANDARDNational forewordThis British St
2、andard is the UK implementation of ISO 13007-1:2010.The UK participation in its preparation was entrusted to TechnicalCommittee B/539, Ceramic tiles and other rigid tiling.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purpo
3、rt to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 68615 3ICS 83.180; 91.100.23Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the
4、Standards Policy and Strategy Committee on 31 October 2010.Amendments issued since publicationDate Text affectedBS ISO 13007-1:2010Reference numberISO 13007-1:2010(E)ISO 2010INTERNATIONAL STANDARD ISO13007-1Second edition2010-09-15Ceramic tiles Grouts and adhesives Part 1: Terms, definitions and spe
5、cifications for adhesives Carreaux cramiques Mortiers de joints et colles Partie 1: Termes, dfinitions et spcifications relatives aux colles BS ISO 13007-1:2010ISO 13007-1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may b
6、e printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts
7、 no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the f
8、ile is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be repr
9、oduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22
10、749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 13007-1:2010ISO 13007-1:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Classificatio
11、n and designation 3 5 Requirements.4 5.1 Substrates 4 5.2 Specifications for cementitious adhesives C 5 5.3 Specifications for dispersion adhesives D 6 5.4 Specifications for reaction resin adhesives R.7 6 Marking, labelling and packaging8 BS ISO 13007-1:2010ISO 13007-1:2010(E) iv ISO 2010 All right
12、s reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for
13、 which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a
14、ll matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are
15、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re
16、sponsible for identifying any or all such patent rights. ISO 13007-1 was prepared by Technical Committee ISO/TC 189, Ceramic tiles. This second edition cancels and replaces the first edition (ISO 13007-1:2004), which has been technically revised. It also incorporates the Technical Corrigendum ISO 13
17、007-1:2004/Cor.1:2006. ISO 13007 consists of the following parts, under the general title Ceramic tiles Grouts and adhesives: Part 1: Terms, definitions and specifications for adhesives Part 2: Test methods for adhesives Part 3: Terms, definitions and specifications for grouts Part 4: Test methods f
18、or grouts BS ISO 13007-1:2010INTERNATIONAL STANDARD ISO 13007-1:2010(E) ISO 2010 All rights reserved 1Ceramic tiles Grouts and adhesives Part 1: Terms, definitions and specifications for adhesives 1 Scope This part of ISO 13007 defines terms concerning the products, working methods and application p
19、roperties for ceramic tile adhesives. It specifies values of performance requirements for all ceramic tile adhesives cementitious (C), dispersion (D) and reaction resin (R) adhesives. This part of ISO 13007 is applicable to ceramic tile adhesives for internal and external tile installations on walls
20、 and floors. It is not applicable to criteria or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can also be used for other types of tiles (natural and agglomerated stones, etc.), where these do not adversely affect the materials. 2 Normative references
21、The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 13006, Ceramic tiles Definitions, classificat
22、ion, characteristics and marking ISO 13007-2:2010, Ceramic tiles Grouts and adhesives Part 2: Test methods for adhesives 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 13006 and the following apply. 3.1 substrate fixing surface surface on which the
23、tile is installed or fixed 3.2 wall and floor tiles tiles made out of ceramic tile or natural and agglomerated stones 3.3 cementitious adhesive C mixture of hydraulic binding agents, aggregates and organic additives, mixed with water or liquid admix immediately prior to use BS ISO 13007-1:2010ISO 13
24、007-1:2010(E) 2 ISO 2010 All rights reserved3.4 dispersion adhesive D ready-for-use mixture of organic binding agent(s) that is in the form of an aqueous polymer dispersion, organic additives and mineral fillers 3.5 reaction resin adhesive R single or multi-component mixture of synthetic resin, mine
25、ral fillers and organic additives in which curing occurs by chemical reaction 3.6 notched trowel toothed tool, which makes it possible to apply the adhesive as a series of ribs of a uniform thickness on to the fixing surface and the reverse face of the tile 3.7 application to one surface only adhesi
26、ve applied only to the fixing surface with a trowel to obtain a uniform layer and then combed with a notched trowel 3.8 application to both surfaces adhesive applied to the fixing surface and to the reverse surface of the tiles 3.9 shelf life time of storage under stated conditions during which an a
27、dhesive can be expected to maintain its working properties 3.10 maturing time interval between the time when the cementitious adhesive is mixed and the time when it is ready for use 3.11 pot life time interval during which the adhesive can be used after mixing 3.12 open time maximum time interval af
28、ter application at which tiles can be embedded in the applied adhesive and meet the specified tensile adhesion strength requirement 3.13 slip downward movement of a tile applied to a combed adhesive layer on a vertical surface 3.14 adjustability maximum time interval after which the tiles position i
29、n the adhesive layer can be adjusted without significant loss of adhesion strength 3.15 adhesion strength maximum strength per unit surface area which can be measured by shear or tensile testing BS ISO 13007-1:2010ISO 13007-1:2010(E) ISO 2010 All rights reserved 33.16 deformability capacity of a har
30、dened adhesive to be deformed by stresses between the tile and the fixing surface without damage to the installed surface 3.17 transverse deformation deflection recorded at the centre when a beam of hardened adhesive is subjected to three point loading 3.18 fundamental characteristic characteristic
31、that is absolutely required of an adhesive 3.19 additional characteristic characteristic of an adhesive for specific service conditions where enhanced levels of performance are required 3.20 special characteristic characteristic of an adhesive which provides further information about its general per
32、formance 4 Classification and designation 4.1 Tile adhesives are classified into three types (see 3.3, 3.4 and 3.5, and ISO 13006): C cementitious adhesive D dispersion adhesive R reaction resin adhesive For each type, there are different possible classes, related to combinations of the different ad
33、ditional and special characteristics, in accordance with Tables 1, 2 and 3. These classes are designated with the following numbers and letters: 1 normal adhesive 2 improved adhesive F fast-setting cementitious adhesive A accelerated drying dispersion adhesive T slip-resistant adhesive E adhesive wi
34、th extended open time S special deformable characteristic for cementitious adhesives only P adhesive with adhesion to exterior glue plywood 4.2 The designation of the adhesive is generated with the symbol of the type (C, D or R), followed by the abbreviation of the class or classes to which it belon
35、gs. Table 1 describes the designation of tile adhesives. BS ISO 13007-1:2010ISO 13007-1:2010(E) 4 ISO 2010 All rights reservedTable 1 Examples of designation and classification Symbol type Number Class Description C 1 Normal cementitious adhesive C 1 F Fast-setting cementitious adhesive C 1 T Normal
36、 cementitious adhesive with slip resistance C 1 FT Fast-setting cementitous adhesive with slip resistance C 2 Cementitious adhesive with improved characteristics C 2 E Cementitous adhesive with improved characteristics and extended open time C 2 F Fast-setting cementitous adhesive with improved char
37、acteristics C 2 T Cementitous adhesive with improved characteristics and slip resistance C 2 TE Cementitious adhesive with improved characteristics, slip resistance and extended open time C 2 FT Fast-setting cementitious adhesive with improved characteristics and slip resistance D 1 Normal dispersio
38、n adhesive D 1 T Normal dispersion adhesive with slip resistance D 2 Dispersion adhesive with improved characteristics D 2 A Accelerated drying dispersion adhesive with improved characteristics D 2 T Dispersion adhesive with improved characteristics with slip resistance D 2 TE Dispersion adhesive wi
39、th improved characteristics, slip resistance and extended open time R 1 Normal reaction resin adhesive R 1 T Normal reaction resin adhesive with slip resistance R 2 Reaction resin adhesive with improved characteristics R 2 T Reaction resin adhesive with improved characteristics and slip resistance N
40、OTE Additional designations can be inserted according to the combination of the different symbols of the characteristics. EXAMPLE Deformable, improved cementitious adhesive with extended open time and normal adhesion to exterior glue plywood: C2ES1P1. 5 Requirements 5.1 Substrates The standard concr
41、ete substrate is mandatory. Other substrates may be used upon agreement, if the substrate is recommended for the ceramic tile application by the adhesive manufacturer. To demonstrate compatibility with other optional substrates, the adhesive shall be applied to the selected substrate in accordance w
42、ith the tensile adhesion strength method given in ISO 13007-2:2010, 4.4.4.2. When the result of W 0,5 N/mm2is achieved or cohesive failure occurs in the substrate, the requirement shall be considered satisfied. BS ISO 13007-1:2010ISO 13007-1:2010(E) ISO 2010 All rights reserved 55.2 Specifications f
43、or cementitious adhesives C Cementitious adhesives shall comply with all of the C1 fundamental characteristics reported in Table 2. The amount of water or liquid admix required for preparing the cementitious adhesive shall be the same for all tests. The additional characteristics for C2 (improved pe
44、rformance) products are also contained in Table 2. Table 3 gives the special characteristics that can be reported for cementitious adhesives. Table 2 Specifications for cementitious adhesives C Classification Property Requirement Test method in ISO 13007-2:2010Tensile adhesion strength W 0,5 N/mm24.
45、4.4.2 Tensile adhesion strength after water immersion W 0,5 N/mm24.4.4.3 Tensile adhesion strength after heat ageing W 0,5 N/mm24.4.4.4 Tensile adhesion strength after freeze-thaw cycle W 0,5 N/mm24.4.4.5 C1 Normal cementitious adhesives (fundamental characteristics) Open time: tensile adhesion stre
46、ngth W 0,5 N/mm2After not less than 20 min 4.1 Tensile adhesion strength W 1,0 N/mm24.4.4.2 Tensile adhesion strength after water immersion W 1,0 N/mm24.4.4.3 Tensile adhesion strength after heat ageing W 1,0 N/mm24.4.4.4 C2 Improved cementitious adhesives (additional characteristics) Tensile adhesi
47、on strength after freeze-thaw cycle W 1,0 N/mm24.4.4.5 BS ISO 13007-1:2010ISO 13007-1:2010(E) 6 ISO 2010 All rights reservedTable 3 Specifications for cementitious adhesives (C) Special characteristics Special characteristic Property Requirement Test method in ISO 13007-2:2010T Slip resistance Slip
48、u 0,5 mm 4.2 Tensile adhesion strength W 0,5 N/mm2 after no more than 6 h 4.4.4.2 Open time: tensile adhesion strength W 0,5 N/mm2 after not less than 10 min 4.1 F Fast-setting adhesives All other requirements at least equal to or better than those listed for C1 adhesives as in Table 2 See Table 2 u
49、nder C1 adhesives See Table 2 under C1 adhesives Deformable adhesive (S1) W 2,5 mm, 5 mm 4.5 S Transverse deformation Highly deformable adhesives (S2) W 5 mm 4.5 E Extended open time Extended open time: tensile adhesion strength W 0,5 N/mm2after not less than 30 min 4.1 Normal exterior glue plywood adhesion (P1) W 0,5 N/mm24.4.4.2 P Exterior glue plywood adhesion (optional substrates) Improved exterior glue plywood adhesion (P2) W 1 N/mm24.4.4.2 5.3 Specificat
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1