BS ISO 13105-1-2014 Building construction machinery and equipment Machinery for concrete surface floating and finishing Terms and commercial specifications《建筑施工机械和设备 混凝土表面浮动处理和精加工机.pdf

1、BSI Standards PublicationBS ISO 13105-1:2014Building constructionmachinery and equipment Machinery for concrete surfacefloating and finishingPart 1: Terms and commercial specificationsBS ISO 13105-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 13105-1:2

2、014. The UK participation in its preparation was entrusted to TechnicalCommittee B/513, Construction equipment and plant and site safety. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary p

3、rovisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 79553 4ICS 01.040.91; 13.110; 91.220Compliance with a British Standard cannot confer immunity from legal obligations.This British S

4、tandard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 13105-1:2014 ISO 2014Building construction machinery and equipment Machinery for concrete surface floating and

5、 finishing Part 1: Terms and commercial specificationsMachines et matriels pour la construction des btiments Talocheuses-lisseuses de mortier Partie 1: Terminologie et spcifications commercialesINTERNATIONAL STANDARDISO13105-1First edition2014-12-01Reference numberISO 13105-1:2014(E)BS ISO 13105-1:2

6、014ISO 13105-1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

7、the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgW

8、eb www.iso.orgPublished in SwitzerlandBS ISO 13105-1:2014ISO 13105-1:2014(E)Contents PageForeword ivIntroduction v1 Scope . 12 Terms and definitions . 13 Commercial specifications . 13.1 General . 13.2 Pedestrian-controlled power trowel 23.3 Ride-on power trowel . 3Annex A (informative) Power trowel

9、 dimensions in operating mode . 4Bibliography 6 ISO 2014 All rights reserved iiiBS ISO 13105-1:2014ISO 13105-1:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stand

10、ards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta

11、ke part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In pa

12、rticular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements o

13、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see

14、 www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence t

15、o the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO ISO/TC 195, Building construction machinery and equipment, Subcommittee SC 1, Machinery and equipment for concrete work.ISO 1310

16、5 consists of the following parts, under the general title Building construction machinery and equipment Machinery for concrete surface floating and finishing: Part 1: Terms and commercial specifications Part 2: Safety requirements and verificationiv ISO 2014 All rights reservedBS ISO 13105-1:2014IS

17、O 13105-1:2014(E)IntroductionISO 13105 deals with machinery designed for smoothing and finishing concrete on construction sites. These machines are commonly referred to as “power trowels.”This part of ISO 13105 provides terminology and definitions for the machine and for specific components of the m

18、achine.It establishes requirements and parameters for stating values typically found in commercial literature in an effort to aid customers and users in product selection and comparison. ISO 2014 All rights reserved vBS ISO 13105-1:2014BS ISO 13105-1:2014Building construction machinery and equipment

19、 Machinery for concrete surface floating and finishing Part 1: Terms and commercial specifications1 ScopeThis part of ISO 13105 defines terms and commercial specifications for machines used for concrete surface floating and finishing (also known as power trowels). This includes pedestrian-controlled

20、 equipment and ride-on equipment.It does not address strike-off type machines, commonly known as screeds.2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.2.1power trowelmotor-powered machine with rotating tools for floating and finishing freshly pla

21、ced concrete2.2rotorrotating assembly including the blades and means to pitch blades2.3bladeworking tool which contacts with the concrete surface2.4handlepoledevice on pedestrian-controlled power trowel to enable the operator to hold and manoeuvre the machine2.5retardantliquid finishing aid2.6pitchi

22、ncluded angle between the surface of the blade and the concrete surfaceNote 1 to entry: This could be fixed or adjustable.3 Commercial specifications3.1 GeneralThe following general data shall be presented.a) model and typeINTERNATIONAL STANDARD ISO 13105-1:2014(E) ISO 2014 All rights reserved 1BS I

23、SO 13105-1:2014ISO 13105-1:2014(E)b) manufacturerc) serial numberd) prime mover (combustion engine or electric, pneumatic or hydraulic motor)1) if combustion engine: type (spark ignition or compression ignition) model manufacturer operating speed min1 engine net power kW (or as specified by engine m

24、anufacturer) fuel type fuel tank capacity litres2) if electric motor: model and type rated power kW rated current A voltage and frequency V Hz number of speeds speed range min13) if pneumatic or hydraulic motor: model and type rated power (pneumatic only) kW displacement (hydraulic only) cc rated pr

25、essure kpa rated flow lpme) number of blades per machinef) pitch range in degreesg) rotor diameter (swept circle of rotor) mmh) rotor speed (min to max) min1i) operating mass kgj) shipping mass kg3.2 Pedestrian-controlled power trowelFor pedestrian-controlled machines, the following shall also be pr

26、esented (see Figure A.1).a) handle type (i.e. short, long, foldable)2 ISO 2014 All rights reservedBS ISO 13105-1:2014ISO 13105-1:2014(E)b) handle height (if fixed height) mmc) handle height (if adjustable) range min/max in mmd) guard ring outer diameter mme) overall length in operating mode mm3.3 Ri

27、de-on power trowelFor ride-on machines, the following shall be also presented.a) swept path width mmb) unswept distance between rotors mmc) retardant tank (if any) capacity litresd) battery capacity (if equipped) Ahe) type of transmission (i.e. mechanical, hydraulic)f) type of steering system (i.e.

28、mechanical, power-assisted)g) overall dimensions (see Figure A.2): length (left to right) mm width (front to back) mm height mmh) operator seat height (from work surface) mm ISO 2014 All rights reserved 3BS ISO 13105-1:2014ISO 13105-1:2014(E)Annex A (informative) Power trowel dimensions in operating

29、 modeDimensions in mm60 max0900 minL1D1D290 maxH3H1H2KeyD1rotor diameter (swept circle of rotor)D2guard ring outer diameterH1height of handle (if fixed)H2minimum height of handle (if adjustable)H3maximum height of handle (if adjustable)L1overall lengthFigure A.1 Pedestrian-controlled power trowel sh

30、own with spark ignition engine4 ISO 2014 All rights reservedBS ISO 13105-1:2014ISO 13105-1:2014(E)Dimensions in mmX1 D190 max60 maxH1H2W1W2D2KeyD1rotor diameter (swept circle of rotor)D2overall width (front to back)H1operator seat height (from work surface)H2overall heightL1overall lengthW1swept pat

31、h widthW2overall width (left to right)X1unswept distance between rotorsFigure A.2 Ride-on type power trowel ISO 2014 All rights reserved 5BS ISO 13105-1:2014ISO 13105-1:2014(E)Bibliography1 EN 12649:2008 + A1:2011, Concrete compaction and smoothing machines Safety6 ISO 2014 All rights reservedBS ISO

32、 13105-1:2014BS ISO 13105-1:2014ISO 13105-1:2014(E) ISO 2014 All rights reservedICS 01.040.91; 91.220Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is i

33、ncorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators an

34、d others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards

35、to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and downl

36、oad PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from o

37、ur Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and interna

38、tional standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscrib

39、ing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Net

40、work Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards a

41、nd other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, so

42、ftware and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI f

43、or commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. D

44、etails and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW