BS ISO 13726-2008 Hydraulic fluid power - Single rod cylinders 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm - Accessory mounting dimensions《液压流体动力 内径为250 mm至500.pdf

1、BRITISH STANDARDBS ISO 13726:2008Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm Accessory mounting dimensionsICS 23.100.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g

2、3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 13726:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 55043 0National forewordThis British Standard is the UK

3、implementation of ISO 13726:2008. It supersedes BS ISO 13726:1998 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee MCE/18, Fluid power systems and components, to Panel MCE/18/-/3, Cylinders.A list of organizations represented on this committee can be ob

4、tained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publicati

5、onDate CommentsReference numberISO 13726:2008(E)INTERNATIONAL STANDARD ISO13726Second edition2008-03-01Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm Accessory mounting dimensions Transmissions hydrauliques Vrins simple tige, srie compact

6、e 16 MPa (160 bar) dalsages 250 mm 500 mm Dimensions dinterchangeabilit des accessoires BS ISO 13726:2008ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards i

7、s normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take par

8、t in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to p

9、repare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility tha

10、t some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13726 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. This second edition cancels and r

11、eplaces the first edition (ISO 13726:1998), which has been technically revised. BS ISO 13726:2008iv Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems is the fluid power cylinder

12、. This is a device that converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. BS ISO 13726:20081Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to

13、 500 mm Accessory mounting dimensions 1 Scope This International Standard specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020-3. The accessories have been designed specifically for use with cylinders manufactu

14、red in accordance with ISO 6020-3, but this does not limit their application. This International Standard covers the following accessories: AP2 rod clevis, female thread (see Figure 1 and Table 1); AP4 rod eye, plain, female thread (see Figure 2 and Table 2); AA4 - L pivot pin (locking plate) (see F

15、igure 3 and Table 3); AL6 locking plate for pivot pin (see Figure 4 and Table 4); AA4 - S pivot pin plain (see Figure 5 and Table 5). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces res

16、ulting from the specified internal diameters of the cylinders and pressures according to ISO 2944 and ISO 3320. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc

17、es, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 2944, Fluid power systems and components Nominal pressures ISO 3320, Fluid power sy

18、stems and components Cylinder bores and piston rod diameters Metric series ISO 5598, Fluid power systems and components Vocabulary ISO 6020-3, Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 mm to 500 mm ISO 8132,

19、 Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series Mounting dimensions for accessories BS ISO 13726:20082 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Accessory mounting dimensions 4.1 Th

20、e mounting dimensions for accessories are shown in Figures 1 to 5 and given in Tables 1 to 5. 4.2 For rod eyes with spherical bearing, use those specified in ISO 8132. 5 Material load capacity All cross-sections shall be selected so that, under the maximum tensile load produced by the cylinder, the

21、yield strength of the material used for the accessories is at least 2,5 times the maximum tensile load. 6 Application instructions 6.1 Installation 6.1.1 A tolerance of f8 is recommended for plain bearing pins (see ISO 286-2). 6.1.2 The rod clevis and the rod eye shall be screwed firmly against the

22、piston rod shoulder before locking. 6.2 Lubrication 6.2.1 Sufficient lubrication for the satisfactory performance of these accessories shall be provided. 6.2.2 The method and frequency of such lubrication depends on the particular operating conditions. 7 Example of ordering designation A plain rod e

23、ye with a bore of CK = 90 mm (that is, type 90) shall be designated as follows: Rod eye ISO 13726 - 90 8 Identification statement (reference to this International Standard) It is strongly recommended to manufacturers who have chosen to conform to this International Standard that the following statem

24、ent be used in test reports, catalogues and sales literature: “Interchangeable cylinder accessory mounting dimensions selected in accordance with ISO 13726, Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm Accessory mounting dimensions.” BS

25、 ISO 13726:20083NOTE A suitable locking device is used. Figure 1 AP2 Rod clevis, female thread Table 1 Dimensions of AP2 Rod clevis, female thread Dimensions in millimetres KK CK CM ER CE AV LE CL XT CU GK aDV bCV Type Typical bore Nominal force N 6H H9 A13 max. JS14 min. min. max. JS13 JS13 min. mi

26、n. 90 250 800 000 M100 3 90 90 100 245 113 115 180 100 56 M12 20 90 110 320 1 250 000 M125 4 110 110 120 290 126 130 220 120 66 M12 20 110 125 360 1 600 000 M125 4 125 125 140 310 126 150 250 120 72 M14 25 125 140 400 2 000 000 M160 4 140 140 160 365 161 170 280 140 77 M14 25 140 180 500 3 200 000 M

27、200 4 180 180 200 470 205 210 360 180 92 M16 25 180 aOptional used with AA 4-L. bOptional. BS ISO 13726:20084 NOTE A suitable locking device is used. Figure 2 AP4 Rod eye, plain, female thread Table 2 Dimensions of AP4 Rod eye, plain, female thread Dimensions in millimetres KK CK EM ER CA AV LE N CV

28、 Type Typical bore Typical rod Nominal force N 6H H9 h13 max. JS14 min. min. max. min. 90 250 140 800 000 M100 3 90 90 100 245 113 110 180 90 110 320 180 1 250 000 M125 4 110 110 120 290 126 130 220 110 125 360 180 1 600 000 M125 4 125 125 140 310 126 150 250 125 140 400 220 2 000 000 M160 4 140 140

29、 160 365 161 170 280 140 180 500 280 3 200 000 M200 4 180 180 200 470 205 210 360 180 BS ISO 13726:20085Figure 3 AA4 - L Pivot pin (locking plate) Table 3 Dimensions of AA4 - L Pivot pin (locking plate) Dimensions in millimetres DK SL KL HL DC JL ZV ZX Type Nominal force N f8 1 0 1 + 0,3 + 0,1 min.

30、max. h13 90 800 000 90 230 35 15 15 15 80 3 110 1 250 000 110 270 35 15 15 15 100 3 125 1 600 000 125 310 40 18 22,5 15 115 3 140 2 000 000 140 340 40 18 25 15 130 3 180 3 200 000 180 425 45 20 30 15 170 3 BS ISO 13726:20086 Key 1 screw ( 2) Figure 4 AL6 Locking plate for pivot pin Table 4 Dimension

31、s of AL6 Locking plate for pivot pin Dimensions in millimetres DB BU SK YL XT CU BO Screw Type Nominal force N DK H13 max. 0 0,2 min. JS13 JS13 JS14 (class 8,8) 90 800 000 90 13,5 50 15 130 100 56 25 M12 30 110 1 250 000 110 13,5 50 15 150 120 66 25 M12 30 125 1 600 000 125 15,5 60 18 155 120 72 30

32、M14 40 140 2 000 000 140 15,5 60 18 170 140 77 30 M14 40 180 3 200 000 180 17,5 60 20 215 180 92 30 M16 40 BS ISO 13726:20087Figure 5 AA4 - S Pivot pin, plain (cotter pin or snap ring type) Table 5 Dimensions of AA4 - S Pivot pin, plain Dimensions in millimetres EK EL ML Type Nominal force N f8 min.

33、 max. 90 800 000 90 190 230 110 1 250 000 110 230 270 125 1 600 000 125 260 300 140 2 000 000 140 290 330 180 3 200 000 180 370 410 BS ISO 13726:2008BS ISO 13726:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing B

34、ritish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is

35、the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front c

36、over. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be

37、addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publ

38、ished as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available wh

39、ich give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For

40、details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on

41、the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored

42、in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.