BS ISO 13733-2012 Ships and marine technology Ship-s mooring and towing fittings Universal fairleads with upper roller《船舶和海洋技术 船舶下锚和拖航设备 带上滚轮的通用导缆器》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 13733:2012Ships and marine technology Ships mooring and towingfittings Universal fairleadswith upper rollerBS ISO 13733:2012 BRITISH STANDARDNational forewordThis British

2、Standard is the UK implementation of ISO 13733:2012.The UK participation in its preparation was entrusted to TechnicalCommittee SME/32/-/4, Ships and marine technology - Outfitting anddeck machinery.A list of organizations represented on this committee can beobtained on request to its secretary.This

3、 publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 69749 4ICS 47.020.50Compliance with a British Standard cannot confer immu

4、nity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2012.Amendments issued since publicationDate Text affectedBS ISO 13733:2012 ISO 2012Ships and marine technology Ships mooring and towing fittings Universal

5、fairleads with upper rollerNavires et technologie maritime Corps-morts et ferrures de remorquage de navires Chaumards universels avec rouleau suprieurINTERNATIONAL STANDARDISO13733First edition2012-07-01Reference numberISO 13733:2012(E)BS ISO 13733:2012ISO 13733:2012(E)ii ISO 2012 All rights reserve

6、dCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address b

7、elow or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 13733:2012ISO 13733:2012(E) ISO 2012 All rights reserved iiiContents PageForew

8、ord ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitions . 14 Classification 14.1 Type . 14.2 Nominal sizes . 15 Dimensions . 26 Materials . 27 Construction . 28 Manufacturing and inspection . 29 Marking . 2Annex A (informative) Basis for strength assessment of universal fairle

9、ads 15Bibliography .18BS ISO 13733:2012ISO 13733:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.

10、 Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Interna

11、tional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standa

12、rds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject

13、of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13733 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery.iv ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)Int

14、roductionThe universal fairlead is a type of ships mooring fitting installed on board to lead the mooring rope from the ships inboard to outboard. ISO 2012 All rights reserved vBS ISO 13733:2012BS ISO 13733:2012Ships and marine technology Ships mooring and towing fittings Universal fairleads with up

15、per roller1 ScopeThis International Standard specifies the design, size and technical requirements for universal fairleads with upper roller(s) installed to lead the mooring rope of a ship.2 Normative referencesThe following referenced documents are indispensable for the application of this document

16、. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.IMO Circular MSC/Circ.1175, Guidance on shipboard towing and mooring equipment3 Terms and definitionsFor the purposes of this document, the

17、 following terms and definitions apply.3.1safe working loadSWLmaximum load in kN on the rope that should normally be applied in service conditions4 Classification4.1 TypeDepending on the construction, universal fairleads are to be classified as the following four types: type 4R: with one rope-passin

18、g opening; type 5RL: with one rope-passing opening with additional guide roller on left side; type 5RR: with one rope-passing opening with additional guide roller on right side; type 7R: with two rope-passing openings.4.2 Nominal sizesThe nominal sizes, Dn, of universal fairleads are denoted by refe

19、rence to the outside diameter of the main roller in millimetres, in terms of the nearest number drawn from a basic series of preferred numbers. For the universal fairleads having the same roller diameter, the alphabetical character is followed by nominal size for the different SWL.The nominal sizes

20、are:140, 160, 180, 200, 250, 300A, 300B, 400A, 400B and 400C.INTERNATIONAL STANDARD ISO 13733:2012(E) ISO 2012 All rights reserved 1BS ISO 13733:2012ISO 13733:2012(E)5 DimensionsUniversal fairleads have dimensions and particulars in accordance with Tables 1, 2, 3 and 4, and Figures 1, 2, 3, 4 and 5.

21、6 MaterialsThe materials of the following components are to be used for manufacturing the universal fairleads: Frame and other plates: weldable steel plates having a yield point of not less than 235 N/mm2except frame with rope guide for nominal size 400A, 400B and 400C shall be made of weldable stee

22、l plates having a yield point of not less than 315 N/mm2. Roller: weldable steel plates having a yield point of not less than 235 N/mm2except rollers for nominal size 400A, 400B and 400C shall be made of weldable steel plates having a yield point of not less than 315 N/mm2, or equivalent steel tubes

23、. Axle: carbon steel having a yield point of not less than 345 N/mm2. Bush: brass or bronze or equivalent.7 Construction7.1 The rollers of the universal fairleads shall be constructed from steel tubes or formed from plate.7.2 The foundation of the universal fairleads shall be determined by the manuf

24、acturer. The foundation and welding connections to the hull shall be guaranteed reliable transmission of the maximum loading of the universal fairleads to hull construction without any plastic deformation or cracks.8 Manufacturing and inspection8.1 All surfaces of the universal fairleads, including

25、welding, shall be free from any visible flaws or imperfections.8.2 All surfaces in contact with the ropes shall be free from surface roughness or irregularities likely to cause damage to the ropes by abrasion.8.3 The universal fairleads shall be coated externally with an anti-corrosion protective fi

26、nish.8.4 All rotating parts shall be provided with greasing.9 Marking9.1 The safe working load (SWL) intended for the use of the universal fairleads shall be noted in the towing and mooring plan available on board for the guidance of the shipmaster as specified in MSC/Circ.1175.9.2 The actual SWL on

27、 board shall be determined by considering the foundation and under deck reinforcement, and it shall be marked on the towing and mooring plan. The actual SWL shall not be over the SWL in this International Standard.9.3 The universal fairleads are to be clearly marked with their SWL by weld bead or eq

28、uivalent. The SWL shall be expressed in tonnes (letter t) and be placed so that it is not obscured during operation of the fitting.EXAMPLE SWL XXX t2 ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)Dimensions in millimetres ISO 2012 All rights reserved 3BS ISO 13733:2012ISO 13733:2012(

29、E)Key1 frame with rope guide2 vertical rollers with housing and washers3 lower horizontal roller with washers4 upper horizontal roller with washers5 vertical axles with stopper6 lower horizontal axle with stoppers7 upper horizontal axle with stoppersaHeight of seat shall be determined in accordance

30、with the hull construction design.bFor nominal size 250 and above.cFor nominal size beween 140 and 200 only.dSide shell.Figure 1 Assembly of type 4R universal fairleads4 ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)Dimensions in millimetres ISO 2012 All rights reserved 5BS ISO 13733

31、:2012ISO 13733:2012(E)Key1 frame with rope guide2 vertical rollers with housing and washers3 lower horizontal roller with washers4 upper horizontal roller with washers5 vertical axles with stopper6 lower horizontal axle with stoppers7 upper horizontal axle with stoppers8 type 5RL9 type 5RRaHeight of

32、 seat shall be determined in accordance with the hull construction design.bFor nominal size 250 and above.cFor nominal size beween 140 and 200 only.dSide shell.NOTE Details not shown in this figure; refer to Figure 1.Figure 2 Assembly of type 5RL and 5RR universal fairleadsTable 1 Dimensions and SWL

33、 of type 4R, 5RL and 5RR universal fairleadsDimensions in millimetresNominal sizeDnB x H D1D2h h1h2b b1b2b3b4w c140 195 150 139,8 114,3 277 130 480 335 515 656 820 140 260 150160 200 150 165,2 114,3 290 145 515 365 570 730 920 140 310 175180 200 150 190,7 139,8 315 155 560 391 620 800 1 000 140 360

34、200200 200 150 216,3 139,8 328 170 590 416 675 896 1 110 140 410 225250 250 200 267,4 165,2 416 195 715 517 825 1 046 1 270 180 520 280300A 300 250 318,5 216,3 517 220 870 618 980 1 206 1 480 200 620 330300B 300 250 318,5 216,3 517 220 870 618 980 1 206 1 480 200 620 330400A 350 250 406,4 216,3 561

35、265 960 756 1 210 1 450 1 750 200 795 420400B 350 250 406,4 216,3 561 265 960 756 1 210 1 450 1 750 200 795 420400C 350 250 406,4 216,3 561 265 960 756 1 210 1 450 1 750 200 795 4206 ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)Table 1 (continued)Dimensions in millimetresNominal siz

36、eDne w1w2T T1T2T3T4fWelding leg lengtha,bSWLcCalculated weightdkgz1z2(kN) (t) 4R 5R140 70 30 100 12 10 10 12 12 3 7 4 137 14 159 194160 83 40 100 14 10 14 14 14 4 7 5 196 20 218 267180 95 40 100 16 10 14 16 16 4 7 5 245 25 279 343200 108 50 100 18 12 16 18 18 6 9 7 314 32 373 455250 133 65 200 22 16

37、 18 20 20 6 11 7 510 52 730 877300A 159 80 200 24 20 22 24 22 7 14 8 687 70 1 173 1 411300B 159 80 200 26 22 24 24 22 8 15 9 736 75 1 267 1 521400A 203 100 200 26 22 22 32 28 7 15 8 981 100 1 710 2 032400B 203 100 200 28 24 26 32 28 8 17 9 1 256 128 1 958 2 332400C 203 100 200 30 26 28 32 28 8 18 9

38、1 373 140 2 114 2 516aWelding with chamfering is available based on the same welding volume/strength.bWelding otherwise mentioned in the figures in this International Standard and in this table: minimum leg length is to be 1/2 of thinner plate thickness.cThe SWL is the maximum applicable rope tensio

39、n.The SWLs shown in this table are for reference only. These are based on the loadings as mentioned in Annex A.The “SWL” may be adjusted depending on the actual loading conditions, and the actual marking shall be agreed between the user and the manufacturer.dThe calculated weight is for reference on

40、ly excluding foundation. ISO 2012 All rights reserved 7BS ISO 13733:2012ISO 13733:2012(E)Dimensions in millimetres8 ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)Key1 frame with rope guide2 vertical rollers with housing and washers3 lower horizontal roller with housing and washers4 u

41、pper horizontal roller with housing and washers5 vertical axles with stopper6 lower horizontal axle with stoppers7 upper horizontal axle with stoppersaHeight of seat shall be determined in accordance with the hull construction design.bFor nominal size 250 and above.cFor nominal size beween 140 and 2

42、00 only.dSide shell.Figure 3 Assembly of type 7R universal fairleadsTable 2 Dimensions and SWL of type 7R universal fairleadsDimensions in millimetres Nominal sizeDnB x H D1D2h h1h2b b1b2b3b4w c140 195 150 139,8 114,3 277 130 480 335 850 1 000 1 160 140 260 150160 200 150 165,2 114,3 290 145 515 365

43、 935 1 100 1 286 140 310 175180 200 150 190,7 139,8 315 155 560 391 1 011 1 200 1 400 140 360 200200 200 150 216,3 139,8 328 170 590 416 1 091 1 320 1 550 140 410 225250 250 200 267,4 165,2 416 195 715 517 1 342 1 580 1 820 180 520 280300A 300 250 318,5 216,3 517 220 870 618 1 598 1 840 2 150 200 62

44、0 330300B 300 250 318,5 216,3 517 220 870 618 1 598 1 840 2 150 200 620 330400A 350 250 406,4 216,3 561 265 960 756 1 966 2 250 2 550 200 795 420400B 350 250 406,4 216,3 561 265 960 756 1 966 2 250 2 550 200 795 420400C 350 250 406,4 216,3 561 265 960 756 1 966 2 250 2 550 200 795 420 ISO 2012 All r

45、ights reserved 9BS ISO 13733:2012ISO 13733:2012(E)Table 2 (continued)Dimensions in millimetres Nominal sizeDne w1w2T T1T2T3T4fWelding leg lengtha,bSWLcCalculated weightdz1z2(kN) (t) (kg)140 70 30 100 12 12 18 12 12 6 9 7 137 14 256160 83 40 100 14 14 20 14 14 6 10 7 196 20 357180 95 40 100 16 16 28

46、16 16 8 11 9 245 25 481200 108 50 100 18 18 28 18 18 8 13 9 314 32 629250 133 65 200 22 26 36 20 20 10 18 10 510 52 1 307300A 159 80 200 24 28 46 24 22 10 20 10 687 70 2 013300B 159 80 200 26 30 48 24 22 10 21 10 736 75 2 154400A 203 100 200 26 30 40 32 28 10 21 10 981 100 2 924400B 203 100 200 28 3

47、2 52 32 28 10 22 10 1 256 128 3 344400C 203 100 200 30 34 54 32 28 10 24 10 1 373 140 3 591aWelding with chamfering is available based on the same welding volume/strength.bWelding otherwise mentioned in the figures in this International Standard and in this table: minimum leg length is to be 1/2 of

48、thinner plate thickness.cThe SWL is the maximum applicable rope tension.The SWLs shown in this table are for reference only. These are based on the loadings as mentioned in Annex A.The “SWL” may be adjusted depending on the actual loading conditions, and the actual marking shall be as agreed between

49、 the user and the manufacturer.dThe calculated weight is for reference excluding foundation.Dimensions in millimetresa) Vertical rollerb) Lower support for vertical roller10 ISO 2012 All rights reservedBS ISO 13733:2012ISO 13733:2012(E)c) Horizontal rollerd) Type 7R horizontal rollere) Horizontal supports for type 7R horizontal rollersKey1 vertical roller2 upper washer for vertical roller3 bushes for vertical roller4 lower washer for vertical roller5 horizon