BS ISO 14535-2001 Photography - Room-light loading packages for electronic scanners and image-setting film and paper rolls - Dimensions and related requirements《摄影技术 电子扫描仪、成像胶片和胶卷的.pdf

1、BRITISH STANDARD BS ISO 14535:2001 Photography Room-light loading packages for electronic scanners and image-setting film and paper rolls Dimensions and related requirements ICS 37.040.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 14535:2001 This British Standard, h

2、aving been prepared under the direction of the Consumer Products and Services Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 7 September 2001 BSI 7 September 2001 ISBN 0 580 38444 6 National foreword This British Standard rep

3、roduces verbatim ISO 14535:2001 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee CPW/42, Photography, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its se

4、cretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standa

5、rds Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers t

6、o understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document c

7、omprises a front cover, an inside front cover, pages i to v, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STAND

8、ARD ISO 14535 First edition 2001-07-15 Reference number ISO 14535:2001(E) OSI 2001 Photography Room-light loading packages for electronic scanners and image-setting film and paper rolls Dimensions and related requirements Photographie Emballages de chargement la lumire artificielle pour scanners lec

9、troniques, et films et rouleaux de papier pour rgler limage Dimensions et exigences connexesii ISO 14535:2001(E) iii Contents Page 1 Scope . 1 2 Normative references . 1 3 Conditions for measurement of dimensions . 1 4 Film and paper dimensions 1 5 Winding orientation . 1 6 Dimensions of flanges 2 7

10、 Packaging . 4 8 Leader 4 9 Package marking 5 10 Compliance . 5 Bibliography. 6ISO 14535:2001(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally

11、carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wo

12、rk. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical c

13、ommittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent right

14、s. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 14535 was prepared by Technical Committee ISO/TC 42, Photography.ISO 14535:2001(E) v Introduction Room-light operation has become increasingly attractive to users of electronic-scanner outp

15、ut equipment and image- setting devices. This equipment requires accurate cassettes and a good sensitized material/equipment interface, especially where accurate registration is an important feature, e.g. in colour work. This International Standard is required in order to define the room-light loadi

16、ng packages which must interface with the above equipment.blankINTERNATIONAL STANDARD ISO 14535:2001(E) 1 Photography Room-light loading packages for electronic scanners and image-setting film and paper rolls Dimensions and related requirements 1 Scope This International Standard applies to room-lig

17、ht loading packages either containing photographic film or paper rolls for electronic scanners or image-setting devices. It specifies the dimensions of the package and its contents, critical equipment interfacing features, and package marking. The prime aim of this International Standard is to ensur

18、e compatibility between room-light loading packages and the equipment in which it is used. Two types of package are recognized. One type uses a rigid flange into which mandrils on the exposing device are inserted. The other type uses a flexible flange and relies on the exposing equipment design to h

19、old the roll correctly in the machine. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications d

20、o not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Me

21、mbers of ISO and IEC maintain registers of currently valid International Standards. ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications. ISO 3772:2000, Photography Rolls of sensitized material for the pre-press industry Dimensions and related requirements. 3 Conditions

22、for measurement of dimensions The dimensions and tolerances specified in this International Standard apply at the time of manufacture, measured under atmospheric conditions of and relative humidity as specified in ISO 554. All measuring instrument calibrations should be conducted at a temperature of

23、 , as specified in ISO 1, and a relative humidity of . 4 Film and paper dimensions The dimensions of the film or paper and labelling shall comply with the appropriate requirements of ISO 3772. 5 Winding orientation The winding configuration of the film or paper shall comply with the appropriate requ

24、irements of ISO 3772. (23 2) C (50 5) % 20 C 50 %ISO 14535:2001(E) 2 6 Dimensions of flanges 6.1 Rigid flange The aim and tolerance dimensions of the internal diameter of the flange ( ), into which the machine cassette mandrel inserts, currently varies in different countries. The aim and tolerance o

25、f is preferred due to its tighter tolerance. However, is recognized because it is the standard in certain countries and functions well in those locations (see Figure 1). Dimension applies to the mouth of the flange hole, which may have a slight taper towards the bottom of the hole in order to easily

26、 draw a (positive) mould from the plastic flange. The thickness of the flange rim ( ) shall be , which contributes to the practical width of the roll. The external diameter of the rim ( ), which contributes to the maximum external dimension of the spooled roll, shall be such that the dimensions give

27、n in clause 7 are not exceeded (see Figure 1). Dimension shall be . Dimension shall be not less than . Dimension shall be . Rigid flanges should insert fully and securely into the film-roll core such that the flange is flush with the spooled material. Dimension shall ensure compatibility with the co

28、res specified in ISO 3772. Incorporation of six fins in the flange design is preferred to aid the machine wind and unwind functions. Figure 1 Rigid flange dimensions A 65,5 0 0,5 mm 65,5 mm 0,5 mm A B 3mm 0,3 mm C 130,5 +0,5 4,0 mm D 37 mm 0,4 mm E 28,6 mm F 52 mm 2mm GISO 14535:2001(E) 3 Dimension

29、shall be not greater than . Dimension shall be CAUTION The maximum tolerance for dimension is critical for proper interchangeability. 6.2 Flexible flange Flanges are required for each of the preferred core sizes specified in ISO 3772. The flanges shall be firmly attached to each end of a core which

30、supports the roll of material and shall provide light- tight protection to the roll edges. The flanges shall not impede the winding or the unwinding of the material on the roll. The internal diameter of the combination of the core plus any portion of the flexible flange shall comply with the minimum

31、 dimensions specified in ISO 3772:2000, 5.3. See Figure 2 for an example of a flexible flange configuration. Key 1 End flange 2 Paper core 3 Light-tight seal area of flange Figure 2 Example of a flexible flange configuration H 3,4 mm I 43 mm 0,5 mm IISO 14535:2001(E) 4 7 Packaging 7.1 Package width

32、7.1.1 Rigid flange The overall maximum width of the spooled film or paper plus room-light loading packaging, required to fit an electronic scanner or input cassette of an image-setting device, shall be up to a maximum material width . 7.1.2 Flexible flange The overall maximum width of the spooled fi

33、lm or paper plus room-light loading packaging, required to fit an electronic scanner or input cassette of an image-setting device, shall be up to a maximum material width . 7.2 External package diameter The maximum external package diameter varies according to the core on which the material is wound

34、. The core, in turn, is related to the specific equipment in use. These shall be in accordance with Table 1. 8L e a d e r 8.1 General requirements The leader material is used both as the initial material feed prior to loading into the exposing device and to protect the sensitized film or paper from

35、light. The leader material shall be sufficiently robust and securely affixed to the film or paper to withstand the initial manual feed prior to disposal of the leader. 8.2 Leader width dimension The width of the leader shall be sufficient to protect the film or paper roll from light penetration, but

36、 not hinder the initial material feed through the machine cassette opening. 8.3 Leader length dimension The leader length shall be sufficient to protect the film or paper roll from light penetration, both during transit and the machine cassette loading operation. Table 1 Package diameter Dimensions

37、in millimetres Core internal diameter Maximum external package diameter 28,8 96 50,7 153 71,9 a 142 a cores have largely replaced cores as the preferred internal diameter (ISO 3772). + 10 mm + 2,5 mm 71,9 mm 71,2 mmISO 14535:2001(E) 5 8.4 Leader splicing The total splice thickness (including the fil

38、m/paper) shall not exceed . The width of the splicing tape shall not protrude beyond the edge of the sensitized material. 9 Package marking Sufficient data shall be provided on a products packaging to inform the user of proper use and handling. Product packaging shall be marked so as to indicate pro

39、duct name and size, conditions of use (such as safelight), and conditions of shipping and storage. To accomplish this, each of the packages which constitute the products packaging should be marked so as to indicate one or more of the following: 1) product name or trade name for unit packages; a reas

40、onable effort shall be made to make this item legible under recommended safelight conditions; name or trade mark of the manufacturer; manufacturers catalogue identification number; bar-code information; information to assist recycling of waste packaging; quantity of units contained in the package; p

41、roduct name or trade name of sensitized material; nominal product dimensions, in metric units, with the smaller dimension first; batch number and/or parent roll number; expiration date or “develop before” date or inventory control code; manufacturers recommended safelight conditions; 2) manufacturer

42、s recommended storage conditions. 2) 10 Compliance If it is desired to indicate compliance of the room-light loading package with this International Standard, the following wording shall be used: “PACKAGE COMPLYING WITH ISO 14535” 1) There can be legal requirements in certain countries for other dat

43、a to be marked on the package. 2) This may be indicated by wording or by a code. 3mmISO 14535:2001(E) 6 Bibliography 1 ISO 1, Geometrical Product Specifications (GPS) Standard reference temperature for geometrical product specifications. 2 ISO 11312:2000, Photography Sheets of sensitized material fo

44、r the pre-press industry Dimensions and related requirements.blankBS ISO 14535:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the i

45、nternational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and service

46、s. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an indivi

47、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards a

48、re also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of inf

49、ormation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and o