BS ISO 15218-2003 Pneumatic fluid power - 3 2 solenoid valves - Mounting interface surfaces《气液传动 3 2电磁阀 安装接口表面》.pdf

1、BRITISH STANDARD BS ISO 15218:2003 Pneumatic fluid power 3/2 solenoid valves Mounting interface surfaces ICS 23.100.50 BS ISO 15218:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 20 February 2003 BSI 20 February 2003 ISBN 0 580 41273 3

2、National foreword This British Standard reproduces verbatim ISO 15218:2003 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee MCE/18, Fluid power systems and components, to Subcommittee MCE/18/-/5, Control components, which has

3、 the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “I

4、nternational Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with

5、a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internatio

6、nal and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5 and a back cover The BSI copyright date displayed in this document indicates when the document

7、was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 15218:2003(E)INTERNATIONAL STANDARD ISO 15218 First edition 2003-02-15 Pneumatic fluid power 3/2 solenoid valves Mounting interface surfaces Transmissions pneumatiques lectrodistributeurs 3/2 Plan de pos

8、e BSISO15218:2003IS:81251 O3002(E) DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide

9、 ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna

10、 f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata

11、 ta teh serddaig sleb nevwo. ISO 3002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mceinahcla, incliduntohp gcoiypodna gn micrfoilm, wittuoh repmissii now nritign from ietI rehSa Ot tsserdda eh e

12、bolw or ISOs memreb i ydobn the cnuotfo yr ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.o gro Web www.iso.org ii ISO 3002 Allr ihgtsser edevrBSISO15218:2003 iiiForeword ISO (the International Organization for

13、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r

14、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internation

15、al Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as

16、 an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. IS

17、O 15218 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components. BSISO15218:2003INTENRATIONAL TSANDADR IS:81251 O3002(E)1Pneumatic fluid power 3/2 solenoid valves Mounting interface surfaces 1 Scope This International Standard specifies

18、 the dimensions of 3/2 solenoid valves for four sizes of mounting interface surfaces, with three holes for flow passages, two holes for fixing screws and requirements for a sealing surface, for use at a maximum rated pressure of 1,6 MPa (16 bar 1) ). 2 Normative references The following referenced d

19、ocuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1302, Geometrical Product Specifications (GPS) Indication of surface te

20、xture in technical product documentation ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 4287, Geometrical Product Specifications (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters I

21、SO 5598, Fluid power systems and components Vocabulary ISO 11727, Pneumatic fluid power Identification of ports and control mechanisms of control valves and other components 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Port identific

22、ation Identify the port in accordance with ISO 11727. Marking at the interface is not required. 1) 1 bar = 10 5Pa = 100 kPa = 0,1 MPa; 1 Pa = 1 N/m 2BSISO15218:20032 5 Dimensions 5.1 Dimensions and tolerances Requirements for dimensions and tolerances for sizes 10 mm, 15 mm and 22 mm are shown in Fi

23、gure 1 and given in Table 1. Requirements for dimensions and tolerances for size 30 mm are shown in Figures 2 and 3. Any tolerances not specified shall be in accordance with ISO 2768-1. 5.2 Tolerances on surface conditions Tolerances on surface conditions of the area within the continuous lines in F

24、igures 1, 2 and 3 shall be as follows: Surface roughness: Ra = 1,6 m (see ISO 4287 and ISO 1302); Surface flatness: 0,05 mm for the whole surface on sizes 10 mm, 15 mm, 22 mm, and 0,1 mm on size 30 mm. 5.3 Interface for 3/2 solenoid valves of widths 10 mm, 15 mm and 22 mm See Figure 1 and Table 1. 5

25、.4 Interface for 3/2 solenoid valves of width 30 mm 5.4.1 With exhaust port See Figure 2. 5.4.2 Non-collectable exhaust See Figure 3. 6 Identification statement (Reference to this International Standard) Use the following statement in test reports, catalogues and sales literature when electing to co

26、mply with this International Standard: “Mounting interface surfaces of 3/2 pneumatic solenoid valves conform to ISO 15218:2002, Pneumatic fluid power 3/2 solenoid valves Mounting interface surfaces.” BSISO15218:2003 3Dimensions in millimetres Key 1 face of the solenoid valve 2 mounting face 3 coil a

27、 Hole for fixing screws T (2 ). b 2 T, depth P. c Interface axis of the identical valve. Figure 1 Interface for 3/2 solenoid valve of widths 10 mm, 15 mm and 22 mm Table 1 Dimensions Dimensions in millimetres A B C D E F G T P Y Size min. max. min. max. 0,1 min. max. min. max. 0,1 0,1 min. min. 10 1

28、,0 1,2 10,0 10,5 6,8 3,8 4,0 6,2 6,4 2,8 1 M1,6 3 11 15 1,6 2,0 15 16 9,7 6,0 6,3 9,0 9,3 3,8 1,4 M3 6 17 22 2,1 2,5 22 23 15 9,0 9,3 13,0 13,3 5,5 2 M3 7 24 BSISO15218:20034 Dimensions in millimetres Key 1 face of the solenoid valve 2 mounting face 3 coil a Hole for fixing screws M4 (2 ). b 2 M4 -

29、6H, minimum depth 8 mm. c Locating hole 3 H13, minimum depth 3 mm. d Interface axis of next identical valve. Figure 2 Interface for 3/2 solenoid valve of width 30 mm with exhaust port BSISO15218:2003 5Dimensions in millimetres Key 1 face of the solenoid valve 2 mounting face 3 coil a Hole for fixing

30、 screws M4 (2 ). b 2 M4 - 6H, minimum depth 8 mm. c Area without obstacle. d Interface axis of next identical valve. e Sealing surface. Figure 3 Interface for 3/2 solenoid valve of width 30 mm with non-collectable exhaust BSISO15218:2003BS ISO 15218:2003 BSI 389 Chiswick High Road London W4 4AL BSI

31、British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users

32、of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary

33、 of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standar

34、ds. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for in

35、ternational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its

36、 Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to dat

37、e with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Sta

38、ndards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization

39、bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the f

40、ree use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.