BS ISO 15550-2016 Internal combustion engines Determination and method for the measurement of engine power General requirements《内燃机 测量发动机功率的测定方法 总要求》.pdf

1、BS ISO 15550:2016Internal combustion engines Determination and methodfor the measurement of enginepower General requirementsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 15550:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementati

2、on of ISO 15550:2016. It supersedes BS ISO 15550:2002 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/14, RIC engines.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpor

3、t to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 92340 1 ICS 27.020 Compliance with a British Standard cannot confer immunity from legal obligations

4、.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 15550:2016 ISO 2016Internal combustion engines Determination and method for the measurement of

5、engine power General requirementsMoteurs combustion interne Dtermination et mthode de mesure de la puissance du moteur Exigences gnralesINTERNATIONAL STANDARDISO15550Second edition 2016-12-01Reference numberISO 15550:2016(E)BS ISO 15550:2016ISO 15550:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT P

6、ROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without p

7、rior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 1

8、5550:2016ISO 15550:2016(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 24 Symbols .115 Standard reference conditions .176 Tests 176.1 General 176.2 Test method 1 176.2.1 Preamble 176.2.2 Test designation .176.2.3 Extent of tests 176.2.4 Measurement techniques

9、 186.2.5 Test conditions196.2.6 Test procedures216.3 Test method 2 246.3.1 General. 246.3.2 Measuring equipment and instrument accuracy 246.3.3 Setting conditions 256.3.4 Test conditions256.3.5 Test procedure 276.3.6 Data to be recorded 277 Method of power correction 277.1 General 277.2 Test atmosph

10、eric conditions 277.3 Correction factor afor naturally aspirated and pressure-charged spark-ignition engines (with or without charge air cooling) 287.4 Correction factor cfor compression-ignition (diesel) engines 287.4.1 General. 287.4.2 Atmospheric factor fa.287.4.3 Engine factor, fm297.4.4 Limitat

11、ion in use of correction factor equation .307.5 Other types of engine . 308 Measurement and correction of smoke value for compression-ignition (diesel) engines 308.1 General 308.2 Correction factor for the smoke light absorption coefficient .318.3 Determination of the correction factor for the smoke

12、 light absorption coefficient .318.4 Limits of application 319 Test report 319.1 Test method 1 319.1.1 General. 319.1.2 Type test report .319.2 Test method 2 329.2.1 General. 329.2.2 Type test report .32Bibliography .43 ISO 2016 All rights reserved iiiContents PageBS ISO 15550:2016ISO 15550:2016(E)F

13、orewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec

14、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o

15、f electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document

16、 was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such p

17、atent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does no

18、t constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information

19、The committee responsible for this document is ISO/TC 70, Internal combustion engines.This second edition cancels and replaces the first edition (ISO 15550:2002), of which it constitutes a minor revision.iv ISO 2016 All rights reservedBS ISO 15550:2016ISO 15550:2016(E)IntroductionThis document estab

20、lishes the framework for ISO engine power measurement standards. By applying this framework, the disadvantages of the existence of many similar, but different, ISO standards for the definition and determination of engine power can be avoided.This framework uses the “Core” and “Satellite” approach. T

21、he “Core” standard contains the requirements that are common to all engine applications described in the scope and the “Satellite” standard contains those requirements that are necessary to tailor power measurement and declaration to suit a particular engine application.This document is only applica

22、ble in conjunction with a particular “Satellite” standard in order to completely specify the requirements for the particular engine application. The “Core” standard, therefore, is not a document that can stand alone, but only represents addenda to a particular “Satellite” standard used to create a c

23、omplete standard together with the said “Satellite” standard.The advantage of this approach is that the use of standards for the same or similar engines used in different applications will be rationalized and the harmonization of standards in the course of revision or development will be ensured.Thi

24、s document is the “Core” standard.This document was prepared in order to serve as the “Core” standard for making engine power measurements. It was drafted in close co-operation with technical committees ISO/TC 22 Road vehicles, ISO/TC 23 Machinery for forestry and agriculture, ISO/TC 127 Earth movin

25、g machinery and ISO/TC 188 Small craft. The prerequisite for any future modification of this document will be the formal approval of all the above technical committees. Together with the “Satellite” standard for each engine application, the “Core” standard serves as the basis for engine power declar

26、ation and measurement. Each technical committee is fully responsible for the administration of its own “Satellite” standard(s).Any further requirements are subject to agreement between the manufacturer and customer. ISO 2016 All rights reserved vBS ISO 15550:2016BS ISO 15550:2016Internal combustion

27、engines Determination and method for the measurement of engine power General requirements1 Scope1.1 This document specifies standard reference conditions and methods of declaring the power, fuel consumption, lubricating oil consumption and test methods for internal combustion engines in commercial p

28、roduction using liquid or gaseous fuels. It is applicable to the following:a) reciprocating internal combustion (RIC) engines (spark-ignition or compression-ignition engines) but excluding free piston engines;b) rotary piston engines.These engines can be naturally aspirated or pressure-charged eithe

29、r using a mechanical pressure-charger or turbocharger.1.2 This document is applicable to engines used for the following:a) land, rail-traction and marine use as defined in ISO 3046-1;b) the propulsion of automotive vehicles as defined in ISO 1585 and ISO 2534;c) motorcycles as defined in ISO 4106;d)

30、 the propulsion of agricultural tractors and machinese) the propulsion of earth-moving machinery as defined in ISO 9249;f) the propulsion of recreational craft or other small marine craft up to 24 m hull length as defined in ISO 8665.This document can be applied to engines used to propel road constr

31、uction machines, industrial trucks and for other applications where no suitable International Standard for these engines exists.It also can be applied to tests performed both on a test bed at a manufacturers works as well as on site.2 Normative referencesThe following documents are referred to in th

32、e text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2710-1, Reciprocating internal combusti

33、on engines Vocabulary Part 1: Terms for engine design and operationISO 3046-4, Reciprocating internal combustion engines Performance Part 4: Speed governingISO 3046-5, Reciprocating internal combustion engines Performance Part 5: Torsional vibrationsISO 3046-6, Reciprocating internal combustion engi

34、nes Performance Part 6: Overspeed protectionISO 3104, Petroleum products Transparent and opaque liquids Determination of kinematic viscosity and calculation of dynamic viscosityINTERNATIONAL STANDARD ISO 15550:2016(E) ISO 2016 All rights reserved 1BS ISO 15550:2016ISO 15550:2016(E)ISO 3675, Crude pe

35、troleum and liquid petroleum products Laboratory determination of density Hydrometer methodISO 5163, Petroleum products Determination of knock characteristics of motor and aviation fuels Motor methodISO 5164, Petroleum products Determination of knock characteristics of motor fuels Research methodISO

36、 5165, Petroleum products Determination of the ignition quality of diesel fuels Cetane engine methodISO 11614, Reciprocating internal combustion compression-ignition engines Apparatus for measurement of the opacity and for determination of the light absorption coefficient of exhaust gasASTM D 240, S

37、tandard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb CalorimeterASTM D 3338/D 3338M, Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 2710-1, ISO 3

38、046-4, ISO 7876-1 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp3.1 Auxiliaries and equipment3.1.1

39、dependant auxiliaryitem of equipment, the presence or absence of which affects the final shaft power output of the engine3.1.2independent auxiliaryitem of equipment that uses power supplied from a source other than the engine3.1.3essential auxiliaryitem of equipment that is essential for the continu

40、ed or repeated operation of the engine3.1.4non-essential auxiliaryitem of equipment that is not essential for the continued or repeated operation of the engine3.1.5standard production equipmentSPEequipment specified by the manufacturer for a particular engine application that is fitted as standard t

41、o the engine 2 ISO 2016 All rights reservedBS ISO 15550:2016ISO 15550:2016(E)3.2 Engine3.2.1engine adjustmentphysical procedure of modifying an engine for the purpose of adapting it to deliver a power adjusted to a different set of ambient conditions, such as by moving the limiting fuel stop, re-mat

42、ching the turbocharger, changing the fuel injection timing or other physical changesNote 1 to entry: Once the modifications have been completed, the engine is an adjusted engine.3.2.2non-adjusted engineengine which is pre-set so that no physical procedure of modifying the engine for the purpose of a

43、dapting it to a different set of ambient conditions is carried out3.2.3engine speednumber of revolutions of the crankshaft in a given period of timeSOURCE: ISO 2710-1:2000, 11.13.2.4declared engine speedengine speed corresponding to the declared power (3.3.1)SOURCE: ISO 2710-1:2000, 11.1.2 modifiedN

44、ote 1 to entry: In some applications, the declared engine speed is named “rated speed”.3.2.5declared intermediate engine speedengine speed less than 100 % of the declared speed, declared by the manufacturer taking into account the specific requirement defined in the relevant “Satellite” standard3.2.

45、6low idle engine speedidling speedlowest steady-state engine speed without loadSOURCE: ISO 2710-1:2000, 11.1.4 modified3.2.7engine speed at maximum torqueengine speed at maximum torque on maximum fuel stop, including additional torque fuel setting, if applicableSOURCE: ISO 3046-4:2009, 2.3.13 modifi

46、ed3.3 Power and load3.3.1declared powervalue of the power, declared by the manufacturer, which an engine will deliver under a given set of circumstancesNote 1 to entry: In some applications, the declared power is named “rated power”.3.3.1.1declared propeller shaft powervalue of the power, declared b

47、y the manufacturer, at the propeller shaft of an engine sold with complete propulsion units or at the coupling to the propeller shaft of an engine sold with reduction and/or reversing gears ISO 2016 All rights reserved 3BS ISO 15550:2016ISO 15550:2016(E)3.3.1.2declared crankshaft powervalue of the p

48、ower, declared by the manufacturer, at the engine power output shaft of an engine sold without reduction or reversing gears, stern drives or sail drive units3.3.2indicated powertotal power developed in the working cylinders as a result of the pressure of the working medium acting on the pistonsSOURC

49、E: ISO 2710-1:2000, 13.13.3.3brake powerpower or the sum of the powers delivered at the end of the crankshaft or its equivalent, with the equipment and auxiliaries fitted as required by the relevant “Satellite” standardNote 1 to entry: See Table 1.Table 1 Equipment and auxiliaries to be installed for the test to determine engine power1 2 3 4 5No. Equipment and auxiliaries Fitted for engine net power test in accordance with ISO 1585 ISO 8665 ISO 9249 ISO 4106Fitted for engine