BS ISO 16131-2012 Leather Upholstery leather characteristics Selection of leather for furniture《皮革 装饰皮革特性 家具用皮革的选择 》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16131:2012Leather Upholstery leathercharacteristics Selection ofleather for furnitureBS ISO 16131:2012 BRITISH STANDARDNational forewordThis British Standard is the UK imp

2、lementation of ISO 16131:2012. The UK participation in its preparation was entrusted to TechnicalCommittee TCI/69, Footwear, leather and coated fabrics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all t

3、he necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012ISBN 978 0 580 66012 2 ICS 59.140.99; 97.140 Compliance with a British Standard cannot confer immunity from legal obligations.In pa

4、rticular, attention is drawn to:Statutory Instrument 1988 No. 1324, The Furniture and Furnishings (Fire) (Safety) Regulations 1988; Statutory Instrument 1989 No. 2358, The Furniture and Furnishings (Fire) (Safety) (Amendment) Regulations 1989; Statutory Instrument 1993 No. 207, The Furniture and Fur

5、nishings (Fire) (Safety) (Amendment) Regulations 1993; and Statutory Instrument 2010 No. 2205, The Furniture and Furnishings (Fire) (Safety) (Amendment) Regulations 2010.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2012.Amendme

6、nts issued since publicationDate Text affectedBS ISO 16131:2012Reference numberISO 16131:2012(E)ISO 2012INTERNATIONAL STANDARD ISO16131First edition2012-02-01Leather Upholstery leather characteristics Selection of leather for furniture Cuir Caractristiques des cuirs pour garniture Slection des cuirs

7、 pour lameublement BS ISO 16131:2012ISO 16131:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without

8、permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2012 All rights

9、reservedBS ISO 16131:2012ISO 16131:2012(E) ISO 2012 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO t

10、echnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates clos

11、ely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draf

12、t International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this docum

13、ent may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16131 was prepared by Technical Committee ISO/TC 120, Leather, Subcommittee SC 2, Tanned leather. It is based on EN 13336:2004, Leather Upholstery leather characteristics Gui

14、de for selection of leather for furniture. BS ISO 16131:2012BS ISO 16131:2012INTERNATIONAL STANDARD ISO 16131:2012(E) ISO 2012 All rights reserved 1Leather Upholstery leather characteristics Selection of leather for furniture 1 Scope This International Standard specifies sampling and test methods, a

15、nd gives recommended values for, upholstery leather for furniture. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

16、ment (including any amendments) applies. ISO 105-B02, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test ISO 2418, Leather Chemical, physical and mechanical and fastness tests Sampling location ISO 2419, Leather Physical and mechanical tests

17、Sample preparation and conditioning ISO 2588, Leather Sampling Number of items for a gross sample ISO 3377-1, Leather Physical and mechanical tests Determination of tear load Part 1: Single edge tear ISO 4044, Leather Chemical tests Preparation of chemical test samples ISO 4045, Leather Chemical tes

18、ts Determination of pH ISO 5402-1, Leather Determination of flex resistance Part 1: Flexometer method ISO 8191-1, Furniture Assessment of the ignitability of upholstered furniture Part 1: Ignition source: smouldering cigarette ISO 8191-2, Furniture Assessment of the ignitability of upholstered furni

19、ture Part 2: Ignition source: match-flame equivalent ISO 11640, Leather Tests for colour fastness Colour fastness to cycles of to-and-fro rubbing ISO 11641, Leather Tests for colour fastness Colour fastness to perspiration ISO 11644, Leather Test for adhesion of finish ISO 15700, Leather Tests for c

20、olour fastness Colour fastness to water spotting ISO 17233, Leather Physical and mechanical tests Determination of cold crack temperature of surface coatings BS ISO 16131:2012ISO 16131:2012(E) 2 ISO 2012 All rights reserved3 General principles This International Standard considers the performance of

21、 different types of leather intended for upholstery. The characteristics, recommended values, and test methods are specified in Tables A.1, A.2, and A.3. Subsidiary characteristics are stated in Table A.4. 4 Sampling 4.1 When possible, the location and identification of laboratory samples shall be i

22、n accordance with ISO 2418. 4.2 The number of samples shall be by agreement between the interested parties except in cases of dispute when the number of samples shall be in accordance with ISO 2588. If the lot size of the leathers is high, the maximum number of samples shall be five. 5 Conditioning

23、and sampling preparation Leather samples shall be conditioned and prepared for physical, mechanical and fastness tests in accordance with ISO 2419. Leather samples for chemical tests shall be conditioned and prepared in accordance with ISO 4044. 6 Characteristics, test methods, and recommended value

24、s The essential characteristics stated in Tables A.1, A.2, and A.3 shall all be taken into account, even if they can have different relative weight in the process of evaluation relative to use. The subsidiary characteristics stated in Table A.4 shall be agreed by the parties concerned according to t

25、he intended end use of the leather. 7 Test report The test report shall contain at least the following information: a) reference to this International Standard; b) all information necessary for the complete identification of the sample; c) the sampling method used, if required; d) date and place of

26、the test; e) test results and number of test specimens; f) conditioning and test atmosphere used; g) any deviation from this International Standard. BS ISO 16131:2012ISO 16131:2012(E) ISO 2012 All rights reserved 3Annex A (normative) Selection criteria for upholstery leather for furniture A.1 Essent

27、ial characteristics, recommended values, and test methods for upholstery leather for furniture See Tables A.1 to A.3. Table A.1 Aniline, sude and nubuck Leather characteristic Recommended value Test method Colour fastness to Change of leather colour and pad staining to-and-fro rubbing, dry, 50 cycle

28、s, grey scale 3 ISO 11640 to-and-fro rubbing, wet, 20 cycles, grey scale 3 ISO 11640 perspiration, 20 cycles, grey scale 3 ISO 11641in which perspiration solution is defined While these values are typical of those expected, it is advisable to issue appropriate guidance with upholstered furniture to

29、inform consumers of likely performance as well as in-service care and maintenance instructions to avoid unnecessary problems. Colour fastness to light, blue scale 3 ISO 105-B02pH of water extract 3,2 ISO 4045 If the pH value is below 4, pH 0,7 Tear strength, N 20 ISO 3377-1BS ISO 16131:2012ISO 16131

30、:2012(E) 4 ISO 2012 All rights reservedTable A.2 Semi-aniline Leather characteristic Recommended value Test method Colour fastness to Change of leather colour and pad staining to-and-fro rubbing, dry, 500 cycles, grey scale 4 ISO 11640 to-and-fro rubbing, wet, 80 cycles, grey scale 3 to 4 ISO 11640

31、perspiration, 50 cycles, grey scale 3 to 4 ISO 11641 in which perspiration solution is defined While these values are typical of those expected, it is advisable to issue appropriate guidance with upholstered furniture to inform consumers of likely performance as well as in-service care and maintenan

32、ce instructions to avoid unnecessary problems. Colour fastness to light, blue scale 4 ISO 105-B02Finish adhesion, dry, N/10 mm 2 ISO 11644pH of water extract 3,2 ISO 4045 If the pH value is below 4, pH 0,7 Tear strength, N 20 ISO 3377-1BS ISO 16131:2012ISO 16131:2012(E) ISO 2012 All rights reserved

33、5Table A.3 Pigmented Leather characteristic Recommended value Test method Colour fastness to Change of leather colour and pad staining to-and-fro rubbing, dry, 500 cycles, grey scale 4 ISO 11640 to-and-fro rubbing, wet, 250 cycles, grey scale 3 to 4 ISO 11640 perspiration, 80 cycles, grey scale 3 to

34、 4 ISO 11641 in which perspiration solution is defined While these values are typical of those expected, it is advisable to issue appropriate guidance with upholstered furniture to inform consumers of likely performance as well as in-service care and maintenance instructions to avoid unnecessary pro

35、blems. Colour fastness to light, blue scale 5 ISO 105-B02Finish adhesion, N/10 mm 2 ISO 11644Flexing endurance 50 000 cycles (no finish damage cracks) ISO 5402-1 pH of water extract 3,2 ISO 4045 If the pH value is below 4, pH 0,7 Tear strength, N 20 ISO 3377-1A.2 Subsidiary characteristics, recommen

36、ded values, and test methods for upholstery leather for furniture See Table A.4. Table A.4 All leather types Leather characteristic Recommended value Test method Burning behaviour Pass ISO 8191-1 and ISO 8191-2 No soaking Cold crack resistance of finish, 15 C No finish cracks ISO 17233 Colour fastne

37、ss to water spotting, grey scale 3 (No permanent swelling) ISO 15700 BS ISO 16131:2012ISO 16131:2012(E) ICS 59.140.99; 97.140 Price based on 5 pages ISO 2012 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and othe

38、r standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (

39、BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the

40、 constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Si

41、milary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 89

42、96 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)

43、20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European

44、and international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contac

45、t Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software an

46、d documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical

47、publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not p

48、reclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: