BS ISO 16162-2012 Cold-rolled steel sheet products Dimensional and shape tolerances《连续冷轧薄钢板产品 尺寸规格及形状公差》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16162:2012Cold-rolled steel sheet products Dimensional and shapetolerancesBS ISO 16162:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation

2、 of ISO 16162:2012. Itsupersedes BS ISO 16162:2010 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/109, Coated and Uncoated Flat Products to be Usedfor Cold Forming.A list of organizations represented on this committee can beobtained on request to i

3、ts secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 76071 6ICS 77.140.50Compliance with a British Standard c

4、annot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate Text affectedBS ISO 16162:2012 ISO 2012Cold-rolled steel sheet products Dimensional and shape to

5、lerancesTles en acier lamines froid Tolrances sur dimensions et formeINTERNATIONAL STANDARDISO16162Fourth edition2012-08-15Reference numberISO 16162:2012(E)BS ISO 16162:2012ISO 16162:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise spec

6、ified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCas

7、e postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16162:2012ISO 16162:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member

8、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental

9、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directive

10、s, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies ca

11、sting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 16162 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 12, Conti

12、nuous mill flat rolled products.This fourth edition cancels and replaces the third edition (ISO 16162:2010), which has been technically revised. ISO 2012 All rights reserved iiiBS ISO 16162:2012BS ISO 16162:2012Cold-rolled steel sheet products Dimensional and shape tolerances1 ScopeThis Internationa

13、l Standard applies to dimensional and shape tolerances for all cold-rolled steel sheet products.Note Cold-rolled steel strip is not covered by this International Standard.2 Dimensional tolerancesDimensional tolerances are given in Tables 1 to 8.Table 1 Thickness tolerances for coils and cut lengthsD

14、imensions and tolerances in millimetresSpecified widthThickness tolerances for specified thicknesses a,b,c,d,e 0,4 0,4 0,6 0,6 0,8 0,8 1,0 1,0 1,2 1,2 1,6 1,6 2,0 2,0 2,5 2,5 3,0 3,0 4,0600 1 200 0,03 0,04 0,05 0,06 0,07 0,09 0,11 0,13 0,15 0,16 1 200 1 5000,05 0,05 0,05 0,07 0,08 0,10 0,12 0,14 0,1

15、6 0,17 1 500 1 800 0,06 0,07 0,08 0,10 0,12 0,14 0,16 0,19 0,19When International Standards that reference this standard permit sheet that is slit to less than 600 mm in width to be considered as sheet, tolerances shall be subject to agreement.aThe thickness tolerances for sheet in coil form are the

16、 same as for sheet supplied in cut lengths but, in cases where welds are present, the tolerances shall be double those given over a length of 15 m in the vicinity of the weld.bFor specified strength levels of Re= 360 MPa and greater, increase the thickness tolerances by 10 %, applying normal roundin

17、g-off procedures.cThickness is measured at any point on the sheet not less than 25 mm from a side edge.dThe specified thickness range captions apply as a specific value.eThe tolerances provided in this table are based on normal thickness (tolerance over and under). For ordered thicknesses other than

18、 nominal, the total tolerance is twice the tabled value and may be distributed as agreed upon between the buyer and seller.Table 2 Width tolerances for coils and cut lengths, not resquaredDimensions and tolerances in millimetresSpecified width Tolerance 1 200+30 1 200 1 500+ 50 1 500+ 60NOTE For res

19、quared material, more restrictive tolerances are subject to negotiation.INTERNATIONAL STANDARD ISO 16162:2012(E) ISO 2012 All rights reserved 1BS ISO 16162:2012ISO 16162:2012(E)Table 3 Length tolerances for cut lengths, not resquaredDimensions and tolerances in millimetresSpecified length Tolerance

20、2 000+100 2 000 8 000+050,%length 8 000+ 400NOTE For resquared material, more restrictive tolerances are subject to negotiation.Table 4 Camber tolerances for coils and cut lengths, not resquaredDimensions and tolerances in millimetresForm Camber toleranceCoils 20 in any 5 000 lengthCut lengths 0,4 %

21、 lengthNOTE Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge as shown in Figure 1. For resquared material, more restrictive tolerances are subject to negotiation.Table 5 Out-of-square tolerance for cut lengths,

22、 not resquaredDimensions Out-of-square toleranceAll thicknesses and all sizes 0,7 % x widthNOTE Out-of-square is the greatest deviation of an end edge from a straight line at right angles to a side and touching one corner as shown in Figure 2. It can also be measured as one-half the difference betwe

23、en the diagonals of the cut length sheet.Table 6 Out-of-square tolerances for resquared materialDimensions and tolerances in millimetresSpecified length Specified width Out-of-square tolerance 3 000 1 200+10 1 200+20 3 000 All widths+20NOTE Out-of-square is the greatest deviation of an end edge from

24、 a straight line at right angles to a side and touching one corner as shown in Figure 2. It can also be measured as one-half the difference between the diagonals of the cut length sheet. When measuring material to resquared tolerances, consideration may have to be given to extreme variations in temp

25、erature.2 ISO 2012 All rights reservedBS ISO 16162:2012ISO 16162:2012(E)Table 7 Standard flatness tolerances for cut lengthsDimensions and tolerances in millimetresSpecified thickness Specified widthFlatness tolerance specified strength level of Re340 MPa 0,7 1 200 12 15 18 1 200 1 500 15 18 21 1 50

26、0 19 22 27 0,7 1, 2 1 200 10 13 16 1 200 1 500 12 15 19 1 500 17 20 25 1,2 1 200 10 10 16 1 200 1 500 12 13 19 1 500 17 19 25NOTE This table does not apply to full hard sheet (CH550).Maximum deviation from a flat horizontal surface: with the sheet lying under its own weight, the maximum distance bet

27、ween the lower surface of the sheet and the flat horizontal surface (maximum deviation from flatness), as shown in Figure 3. This table also applies to sheet cut to length from coil by the customer when agreed-upon flattening procedures are performed.Table 8 Restricted flatness tolerances for cut le

28、ngthsDimensions and tolerances in millimetresSpecified thickness Specified widthFlatness tolerance specified strength level of Re340 MPa 0,7 1 200 5 8 1 200 1 500 6 9 1 500 8 12 0,7 1, 2 1 200 4 6 1 200 1 500 5 8 1 500 7 10 1,2 1 200 4 5 1 200 1 500 5 6 1 500 6 9 NOTE This table does not apply to fu

29、ll hard sheet (CH550).Maximum deviation from a flat horizontal surface: with the sheet lying under its own weight, the maximum distance between the lower surface of the sheet and the flat horizontal surface (maximum deviation from flatness), as shown in Figure 3. This table also applies to sheet cut

30、 to length from coil by the customer when agreed-upon flattening procedures are performed. ISO 2012 All rights reserved 3BS ISO 16162:2012ISO 16162:2012(E)Key1 edge camber2 side edge (concave side)3 straight edgeFigure 1 Measurement of camberKey1 out-of-square2 straight edge3 side edgeFigure 2 Measu

31、rement of out-of-squareKey1 maximum deviation from flatnessFigure 3 Measurement of flatness4 ISO 2012 All rights reservedBS ISO 16162:2012BS ISO 16162:2012ISO 16162:2012(E) ISO 2012 All rights reservedICS 77.140.50Price based on 4 pagesThis page deliberately left blankBSI is the independent national

32、 body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are publishe

33、d by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure tha

34、t they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the i

35、dentity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the lates

36、t editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicat

37、ionscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI

38、provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof

39、 standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is avai

40、lable on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has

41、 formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise

42、without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: