BS ISO 16236-2013 Crop protection equipment Test method for the determination of drainable volume and its concentration《植物保护设备 可排水体积及其浓度测定的试验方法》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16236:2013Crop protection equipment Test method for thedetermination of drainablevolume and its concentrationBS ISO 16236:2013 BRITISH STANDARDNational forewordThis Britis

2、h Standard is the UK implementation of ISO 16236:2013.The UK participation in its preparation was entrusted to TechnicalCommittee AGE/15, Equipment for crop protection and applicationof liquid fertilizer.A list of organizations represented on this committee can beobtained on request to its secretary

3、.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 74673 4ICS 65.060.40Compliance with a British Standard cannot confer

4、 immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 16236:2013 ISO 2013Crop protection equipment Test method for the determination of drainabl

5、e volume and its concentrationMatriel de protection des cultures Mthodes dessai pour lvaluation du volume vidangeableINTERNATIONAL STANDARDISO16236First edition2013-06-01Reference numberISO 16236:2013(E)BS ISO 16236:2013ISO 16236:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO

6、 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requ

7、ested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16236:2013ISO 16236:2013(E) ISO 2013 All

8、 rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Terms and definitions . 13 Test conditions . 14 Test 14.1 Test liquid 14.2 Test procedure . 1Annex A (normative) Minimum content of test report 4Bibliography 6BS ISO 16236:2013ISO 16236:2013(E)ForewordISO (the International Organ

9、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

10、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

11、The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the

12、 editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent right

13、s identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee respo

14、nsible for this document is ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 6, Equipment for crop protection.iv ISO 2013 All rights reservedBS ISO 16236:2013ISO 16236:2013(E)IntroductionThe cleaning of sprayers becomes more and more important especially for the follow

15、ing reasons: to avoid the contamination of the environment and the operator; the accidental release of agrochemicals that may cause crop damage, raise residue fears or lead to mixing of incompatible crop protection products.In addition, it is likely that the relevant bodies of the industry will need

16、 guidance in developing systems for cleaning the sprayer for emptying the sprayer as far as possible, to enable the evaluation of the state of the art and to establish a basis for future specifications.The main purpose of ISO 16236 is to define the standardized procedure to determine the drainable v

17、olume which can be emptied in the field after carrying out the cleaning procedure as recommended by the sprayer manufacturer. This drainable volume can be relevant when letting out the rinsing liquid (drainable volume) of the tank by using its outlet. Furthermore, other outlets should be included (e

18、.g. suction filter, pressure filter, filling connection). In this sense, this International Standard completes ISO 13440 and ISO 22368-1 to -3. ISO 2013 All rights reserved vBS ISO 16236:2013BS ISO 16236:2013Crop protection equipment Test method for the determination of drainable volume and its conc

19、entration1 ScopeThis International Standard specifies the test method for the determination of the volume and the concentration of the drainable volume of sprayers, in connection to the emptying of the diluted residue of the spray tank by using its outlet and other outlets allowing draining (e.g. su

20、ction filter, filling connection) at the end of the cleaning procedure.It applies to agricultural sprayers used for crop protection and liquid fertiliser applications for both brand new sprayers and sprayers already in use.2 Terms and definitionsFor the purposes of this document, the following terms

21、 and definitions apply.2.1drainable volumeamount of liquid collectable from the spray tank outlet and/or other outlets, intended for emptying the sprayer at the end of the cleaning procedure2.2rinsing systemsystem that is fitted onto sprayers and used for the internal cleaning of the complete spraye

22、r including the tank3 Test conditionsTemperature of the test liquid: 5 C to 30 C.Air temperature: 5 C to 30 C.Relative humidity of air: 30 %.4 Test4.1 Test liquidThe preferred test liquid is water with an approximate concentration of 0,000 1 % of fluorescein sodium (extra pure).Other traced liquids

23、may be used, if the same level of measuring performance can be demonstrated.4.2 Test procedure4.2.1 The test shall be carried out with the sprayer kept in a stationary and horizontal position. The internal surfaces of the complete sprayer shall be carefully cleaned at the start of the test.4.2.2 Fil

24、l up the tank with water to at least 10 % of the nominal tank volume and introduce approximately 1 mg of the tracer per litre of water into the tank through the tank opening with the agitator(s) running. If the sprayer is equipped with an induction hopper, it should not be used in order to avoid its

25、 contamination. INTERNATIONAL STANDARD ISO 16236:2013(E) ISO 2013 All rights reserved 1BS ISO 16236:2013ISO 16236:2013(E)To ensure the same contamination as in normal practice, use and operate all functions needed during the spraying process as specified in the operators manual. Run the agitator(s)

26、for at least 1 min. Open the outlet valve, collect test liquid enough to ensure the contamination of the outlet device and refill it again to the main tank. To contaminate the complete sprayer (hydraulic circuit and internal parts of the main tank), operate all valves as specified by the operators m

27、anual and spray an appropriate amount of test liquid. For sprayers without agitation, contaminate the internal part of the tank by shaking or turn off the equipment several times.4.2.3 Take one representative sample of at least 50 ml, from the sprayer tank to check the concentration of the test liqu

28、id. Enter the concentration in Table A.1.4.2.4 Empty the tank as in normal spraying practice (e.g. normal PTO speed, pressure, nozzle size, nozzle number, flow rate) by using all nozzles (e.g. the whole spray boom). Allow the pump to run for 1 min 5 s after the liquid fan from the nozzles has collap

29、sed to ensure that all relevant liquid has been emptied. For shutting off the pump when completely emptying the tank the specification in the instruction handbook apply, if available.4.2.5 Operate the rinsing system of the sprayer according to the operators manual. If no special rinsing instructions

30、 from operators manual are available carry out a rinsing procedure where the rinsing water is used in three portions. Each portion equals to one third of the volume of the clear water tank or 10 % of the nominal volume of the spray tank divided by three. Measure the volume of each portion of rinsing

31、 water with a maximum error of 2 % of its nominal volume. After each step of this procedure, spray the rinsing liquid as in normal spraying practice.If no rinsing system is available, carry out a rinsing procedure where the rinsing water is used in three portions with a clean water volume correspond

32、ing to at least 10 % of the nominal tank volume of the sprayer. For this purpose, the rinsing water is to be filled in by the filling opening.When each rinsing process is coming to the end, ensure that the agitators are switched off before the pump sucks air in and wait till there is not any liquid

33、coming out of the nozzles, so that the drainable volume is minimized.4.2.6 After the rinsing process, stop the pump drive, operate all relevant valves allowing to discharge the liquid still present in the hydraulic circuit and let the drainable volume out of the tank by using its outlet. Open other

34、outlets allowing draining tool-free (e.g. suction filter, pressure filter, further discharge valves positioned along the hydraulic circuit, filling connection) and make sure to collect all the liquids running out in separate clean containers. Measure the collected volumes individually and record the

35、m in Table A.2.4.2.7 Take one representative sample, of at least 50 ml, out of each container.4.2.8 Conduct the test procedure from 4.2.1 to 4.2.7 at least three times.4.2.9 Determine the concentration of the tracer in the samples taken in 4.2.3 and 4.2.7 by using appropriate methods with a maximum

36、error of 0,01 % of the original tank concentration. Record these concentrations in Table A.3.4.2.10 Calculate the total amount of tracer of the collected drainable volumes (using Table A.4) by multiplying the volumes measured in 4.2.6 (Table A.2) and the concentrations determined in 4.2.9 (Table A.3

37、). Calculate also the total amount of tracer from these measurements.4.2.11 Calculate the mean values and the coefficients of variation Cvof measured volumes and concentrations (using Tables A.2 to A.4). Each Cvshould not exceed 15 %. If one or more Cvvalues are higher than 15 %, repeat the test.4.2

38、.12 Calculate the fraction F of the mean concentration of the samples taken according to 4.2.3 and 4.2.6 as percentage using the following equation (using Table A.5):2 ISO 2013 All rights reservedBS ISO 16236:2013ISO 16236:2013(E)FCCR= 100% 4.2.13 Report the data in the test report (see Annex A). IS

39、O 2013 All rights reserved 3BS ISO 16236:2013ISO 16236:2013(E)Annex A (normative) Minimum content of test reportA.1 Sprayer data Type of sprayer: Nominal spray tank capacity (l): Type and size of spraying nozzles: Spray pressure and flow rate of spraying nozzle: Type and size of rinsing nozzle(s): T

40、ype of rinsing system: Manually: Automatically: Continuous: Non-continuous: Number of rinses: Clear water volume used per rinse (l): Liquid output of rinsing nozzle (l/min): Nominal capacity of rinsing water tank (l): Amount of rinse water used (l): Working width of spray boom (m): Tests were made a

41、ccording to instruction handbook: yes no A.2 Measurement dataA.2.1 Concentration of test liquid (4.2.3)Table A.1 Concentration of test liquid (4.2.3)Measurement dataTest 1 mg/lTest 2 mg/lTest 3 mg/lMean mg/lSample R (CR)4 ISO 2013 All rights reservedBS ISO 16236:2013ISO 16236:2013(E)A.2.2 Volumes of

42、 liquid after rinsing (4.2.6)Table A.2 Volumes of liquid after rinsing (4.2.6)Measurement dataTest 1 lTest 2 lTest 3 lMean lCvvalue %V1(tank sump)V2(suction filter)V3(filling connection)V4()Total volume (Vt)A.2.3 Concentration of liquids after rinsing (4.2.9)Table A.3 Concentration of liquids after

43、rinsing (4.2.9)Measurement dataTest 1 mg/lTest 2 mg/lTest 3 mg/lMean mg/lCvvalue %C1(tank sump)C2(suction filter)C3(filling connection)C4()A.2.4 Amount of tracer in drainable volumes (4.2.10)Table A.4 Amount of tracer in drainable volumes (4.2.10)Measurement dataTest 1 mgTest 2 mgTest 3 mgMean mgCvv

44、alue %m1(tank sump)m2(suction filter)m3(filling connection)m4()Total amount of tracer (mt)A.2.5 Fraction of mean concentration of liquids after rinsing in drainable volume (4.2.12)Table A.5 Fraction of mean concentration of samples as percentage of test liquidMeasurement data Mean %F1(tank sump)F2(s

45、uction filter)F3(filling connection)F4() ISO 2013 All rights reserved 5BS ISO 16236:2013ISO 16236:2013(E)Bibliography1 ISO 13440, Equipment for crop protection Agricultural sprayers Determination of the volume of total residual2 ISO 22368-1, Crop protection equipment Test methods for the evaluation

46、of cleaning systems Part 1: Internal cleaning of complete sprayers3 ISO 22368-2, Crop protection equipment Test methods for the evaluation of cleaning systems Part 2: External cleaning of sprayers4 ISO 22368-3, Crop protection equipment Test methods for the evaluation of cleaning systems Part 3: Int

47、ernal cleaning of tank6 ISO 2013 All rights reservedBS ISO 16236:2013BS ISO 16236:2013ISO 16236:2013(E) ISO 2013 All rights reservedICS 65.060.40Price based on 6 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards

48、-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising

49、 standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyo