BS ISO 16365-1-2014 Plastics Thermoplastic polyurethanes for moulding and extrusion Designation system and basis for specifications《塑料 模制和挤制热塑聚氨酯 命名系统和基本规格》.pdf

1、BSI Standards PublicationBS ISO 16365-1:2014Plastics Thermoplasticpolyurethanes for mouldingand extrusionPart 1: Designation system and basis forspecificationsBS ISO 16365-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16365-1:2014.The UK participation

2、in its preparation was entrusted to TechnicalCommittee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for it

3、s correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 74123 4ICS 83.080.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and St

4、rategy Committee on 31 May 2014.Amendments issued since publicationDate Text affectedBS ISO 16365-1:2014 ISO 2014Plastics Thermoplastic polyurethanes for moulding and extrusion Part 1: Designation system and basis for specificationsPlastiques Polyurthannes thermoplastiques pour moulage et extrusion

5、Partie 1: Systme de dsignation et base de spcificationINTERNATIONAL STANDARDISO16365-1First edition2014-05-01Reference numberISO 16365-1:2014(E)BS ISO 16365-1:2014ISO 16365-1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, n

6、o part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs memb

7、er body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16365-1:2014ISO 16365-1:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope

8、 . 12 Normative references 13 Designation system 23.1 General . 23.2 Data block 1 . 33.3 Data block 2 . 33.4 Data block 3 . 43.5 Data Block 4 . 53.6 Data block 5 . 74 Examples of designations 7Bibliography 9BS ISO 16365-1:2014ISO 16365-1:2014(E)ForewordISO (the International Organization for Standar

9、dization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to

10、 be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used

11、 to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of

12、 the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified

13、during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the

14、meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC

15、61, Plastics, Subcommittee SC 9, Thermoplastic materials.ISO 16365 consists of the following parts, under the general title Plastics Thermoplastic polyurethanes for moulding and extrusion: Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination

16、 of properties Part 3: Distinction between ether and ester polyurethanes by determination of the ester group contentiv ISO 2014 All rights reservedBS ISO 16365-1:2014INTERNATIONAL STANDARD ISO 16365-1:2014(E)Plastics Thermoplastic polyurethanes for moulding and extrusion Part 1: Designation system a

17、nd basis for specifications1 ScopeThis part of ISO 16365 establishes a system of designation for thermoplastic polyurethane elastomers, which is based on ISO 1043 (all parts) and ISO 11469.The designation system may be used as the basis for specifications.The designation system is applicable to all

18、thermoplastic polyurethane elastomers. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colourants, fillers or other additives, etc.The types of thermoplastic polyurethane are differentiated from each other by a classification system

19、based on appropriate levels of the designatory properties:a) hardness;b) tensile modulus of elasticity (optional);and on information about the alternating hard and soft segments in the main chain, the intended application and/or method of processing, important properties, additives, colour, fillers,

20、 and reinforcing materials.It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 16365 does not provide engineering data, performance data, or data on processing conditions which may be required to specify a material for a part

21、icular application and/or method of processing. If such additional properties are required, it is intended that they be determined in accordance with the test methods specified in ISO 16365-2, if suitable.In order to specify a thermoplastic elastomer for a particular application or reproducible proc

22、essing, additional requirements are intented to be given in data block 5 (see 3.1 and 3.6).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies.

23、For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 527 (all parts), Plastics Determination of tensile propertiesISO 868, Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness)ISO 1043-4, Plastics S

24、ymbols and abbreviated terms Part 4: Flame retardantsISO 11469, Plastics Generic identification and marking of plastics productsISO 18064, Thermoplastic elastomers Nomenclature and abbreviated terms ISO 2014 All rights reserved 1BS ISO 16365-1:2014ISO 16365-1:2014(E)ISO 16365-2, Plastics Thermoplast

25、ic polyurethanes for moulding and extrusion Part 2: Preparation of test specimens and determination of properties3 Designation system3.1 GeneralThe designation system for polyurethanes is based on the following standardized pattern (Figure 1).DesignationIdentity BlockDescription block(optional)Inter

26、national Standard BlockIndividual Item BlockData Block 1Data Block 2Data Block 3Data Block 4Data Block 5Figure 1 Data block designation systemThe designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an

27、 individual item block. For unambiguous designation, the individual item block is subdivided into five data blocks comprising the following information. Data block 1: Identification of the thermoplastic polyurethane by its abbreviated symbol (TPU), in accordance with ISO 18064, and optional informat

28、ion on the alternating hard and soft segments in the main chain (see 3.2). Data block 2: Fillers or reinforcing materials including summarized nominal content (3.3): important properties, modifier, and flame retardant (3.3); declaration of recyclate: R followed by a number representing the percentag

29、e by mass of recyclate (3.3). Data block 3: Application and processing: Position 1: method of processing (3.4); Positions 2 and further: additives, supplementary information and other characteristics (3.4). Data block 4: Designatory properties (3.5): hardness; modulus. Data block 5: For the purpose

30、of specifications, a fifth data block containing additional information may be used (see 3.6). The kind of information and the code-letters used are not the subject of this part of ISO 16365.The first character of the individual item block shall be a hyphen.The five data blocks shall be separated fr

31、om each other by a comma.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).Terminal commas may be omitted.2 ISO 2014 All rights reservedBS ISO 16365-1:2014ISO 16365-1:2014(E)For part marking the first two data blocks of the designation are u

32、sed, connected with a hyphen, and placed between the punctuation marks and Part marking 7 but 12 45A15 12 but 17 56A20 17 but 22 67A25 22 but 27 75A30 27 but 32 81A35 32 but 37 86A40 37 but 42 90A45 42 but 47 95A50 47 but 52 95A55 52 but 5760 57 but 6265 62 but 6770 67 but 7275 72 but 7780 77NOTE Th

33、e hardness of thermoplastic elastomers is measured in Shore A and Shore D according to ISO 868. Shore hardness is a measure of the resistance of a material to the penetration of a needle under a defined spring force. It is determined as a number from 0 to 100 on the scales A or D. The higher the num

34、ber, the higher the hardness of the material. The Shore A is used for (very) flexible types and the Shore D for flexible and more rigid types. The Shore A and D ranges do overlap. Therefore, for designation purposes a parameter combining the hardness ranges of the Shore A and D is used as this scale

35、 which covers the whole range and is able to discriminate between rather flexible, medium and rigid materials. For values around and above 50 this parameter is identical to the Shore D hardness.3.5.3 Tensile modulus of elasticityThe tensile modulus of elasticity shall be determined in accordance wit

36、h ISO 527 (all parts).The possible values of the tensile modulus of elasticity are divided into 10 ranges, each represented by a 3-figure code-number as specified in Table 4.6 ISO 2014 All rights reservedBS ISO 16365-1:2014ISO 16365-1:2014(E)Table 4 Code-numbers used for tensile modulus of elasticit

37、y in data block 4Code-numberRange of modulus MPa002 30004 30 but 50006 50 but 70008 70 but 90010 90 but 110015 110 but 200025 200 but 300040 300 but 500075 500 but 1000200 1 000 but 3 000400 3 000 but 6 000800 6 000 but 10 000999 10 0003.6 Data block 5Indication of additional requirements in optiona

38、l data block 5 is a way of transforming the designation of a material into a specification for a particular application. This may be done for example by reference to a suitable national standard or to a standard-like, generally established specification (see Clause 4).4 Examples of designationsEXAMP

39、LE 1 A unstabilized polyurethane thermoplastic elastomer (TPU) based on aromatic isocyanate (AR) and polyetherol (ET), natural (not coloured) (N) intended for general (G) and having a Shore A hardness of 85 corresponding to a Shore D hardness of 35 (35) and unknown tensile modulus of elasticity woul

40、d be designated:DesignationDescrip-tion block (optional)Identity blockInterna-tional StandardIndividual item blockData block 1Data block 2Data block 3Data block 4Data block 5Polymer Performance and originApplication and processingPropertiesAdditional informa-tionTypesegment (optional)FillerFlame ret

41、ard-antRecyclateProcess-ingCharacteris-ticsThermo-plastics16365 TPU -ARET G N 35-X Part marking Part marking No No Yes Yes No No NoDesignation: Thermoplastics ISO 16365 TPU-ARES, GF, MHNOW,75-200,8 ISO 2014 All rights reservedBS ISO 16365-1:2014ISO 16365-1:2014(E)Bibliography1 ISO 472, Plastics Voca

42、bulary2 ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics3 ISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials4 ISO 1043-3, Plastics Symbols and abbreviated terms Part 3: Plasticizers ISO 2014 All righ

43、ts reserved 9BS ISO 16365-1:2014ISO 16365-1:2014(E) ISO 2014 All rights reservedICS 83.080.20Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorpora

44、ted by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others

45、 to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help

46、them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF

47、versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Custo

48、mer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international s

49、tandards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. Yo