BS ISO 16611-2017 Plastics piping systems for drainage and sewerage without pressure Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unr.pdf

1、Plastics piping systems for drainage and sewerage without pressure Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) Dimensions, requirements and testsBS ISO 16611:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_

2、AW.indd 1 15/05/2013 15:06 ISO 2017Plastics piping systems for drainage and sewerage without pressure Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) Dimensions, requirements and testsSystmes de canalisation en plastiques

3、 pour rseaux dassainissement sans pression Tuyaux non-circulaires, assemblages de tuyaux et raccords en plastiques thermodurcissables renforcs de verre (PRV) base de rsines de polyester non satur (UP) Dimensions, exigences et essaisINTERNATIONAL STANDARDISO16611First edition2017-06Reference numberIS

4、O 16611:2017(E)National forewordThis British Standard is the UK implementation of ISO 16611:2017.The UK participation in its preparation was entrusted to Technical Committee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can be obtained on r

5、equest to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 89406 0ICS 91.140.80; 23.040.45; 93.030; 23

6、.040.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 16611:

7、2017 ISO 2017Plastics piping systems for drainage and sewerage without pressure Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) Dimensions, requirements and testsSystmes de canalisation en plastiques pour rseaux dassainis

8、sement sans pression Tuyaux non-circulaires, assemblages de tuyaux et raccords en plastiques thermodurcissables renforcs de verre (PRV) base de rsines de polyester non satur (UP) Dimensions, exigences et essaisINTERNATIONAL STANDARDISO16611First edition2017-06Reference numberISO 16611:2017(E)BS ISO

9、16611:2017ISO 16611:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, includi

10、ng photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +4

11、1 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 16611:2017ISO 16611:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe

12、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC

13、h. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 16611:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24 General requirements . 84.1 Classification . 84.1.1 Categories 84

14、.1.2 Nominal size 84.2 Materials . 84.2.1 General 84.2.2 Reinforcement 84.2.3 Resin . 84.2.4 Aggregates and fillers 94.2.5 Elastomers . 94.2.6 Metals 94.3 Wall construction 94.3.1 Inner layer . 94.3.2 Structural layer 94.3.3 Outer layer . 94.3.4 Appearance . 94.4 Reference conditions for testing . 1

15、04.4.1 Temperature . 104.4.2 Properties of water for testing 104.4.3 Loading conditions 104.4.4 Conditioning . 104.4.5 Measurement of dimensions 104.4.6 Elapsed time for determination of long-term properties, (x) 104.5 Joints . 104.5.1 General. 104.5.2 Types of joint 104.5.3 Flexibility of the joint

16、ing system .104.5.4 Sealing ring 114.5.5 Adhesives . 115 Pipes .115.1 Geometrical characteristics 115.1.1 Dimensions 115.2 Mechanical characteristics. 125.2.1 General. 125.2.2 Short-term bending modulus 135.2.3 Long-term creep bending modulus 145.2.4 Short-term bending strength . 145.2.5 Long-term b

17、ending strength 155.2.6 Resistance to strain corrosion . 165.2.7 Minimum initial longitudinal tensile strength 175.3 Marking 186 Fittings .196.1 All types 196.1.1 General. 196.1.2 Diameter series 196.1.3 Mechanical characteristics of fittings .196.1.4 Installed leak tightness of fittings 19 ISO 2017

18、 All rights reserved iiiContents PageBS ISO 16611:2017ISO 16611:2017(E)6.1.5 Dimensions 196.2 Marking 197 Joint performance 207.1 General 207.1.1 Requirements 207.1.2 Test temperature 207.1.3 Dimensions 207.2 Flexible joints 207.2.1 General. 207.2.2 Maximum allowable draw 207.2.3 Maximum allowable a

19、ngular deflection .207.2.4 Maximum allowable misalignment . 207.2.5 Flexible non-end-load-bearing joints with elastomeric sealing rings 207.3 Rigid joints . 227.3.1 Wrapped or cemented 22Annex A (informative) Examples for static calculation 24Bibliography .25iv ISO 2017 All rights reservedBS ISO 166

20、11:2017ISO 16611:2017(E)6.1.5 Dimensions 196.2 Marking 197 Joint performance 207.1 General 207.1.1 Requirements 207.1.2 Test temperature 207.1.3 Dimensions 207.2 Flexible joints 207.2.1 General. 207.2.2 Maximum allowable draw 207.2.3 Maximum allowable angular deflection .207.2.4 Maximum allowable mi

21、salignment . 207.2.5 Flexible non-end-load-bearing joints with elastomeric sealing rings 207.3 Rigid joints . 227.3.1 Wrapped or cemented 22Annex A (informative) Examples for static calculation 24Bibliography .25iv ISO 2017 All rights reserved ISO 16611:2017(E)ForewordISO (the International Organiza

22、tion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

23、has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The

24、 procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the ed

25、itorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent

26、 rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For

27、an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.The co

28、mmittee responsible for this document is ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. ISO 2017 All rights reserved vBS ISO 16611:2017ISO 16611:2017(E)IntroductionThe goal to establish this

29、 product standard is to standardize the requirements for non-circular GRP pipes.This document specifies the requirements for non-circular GRP pipe systems, designed to be used for the renovation of existing channels or open cut installation.This document specifies dimensions, requirements and tests

30、of non-circular pipes including short and long-term properties. To establish long-term properties, it is recommended to use the circular pipes samples.Annex A shows commonly used calculation methods but only as information. The calculation method is selected by the designer.This document does not in

31、clude the recommended practice for installation as this should be a separate document.vi ISO 2017 All rights reservedBS ISO 16611:2017ISO 16611:2017(E)IntroductionThe goal to establish this product standard is to standardize the requirements for non-circular GRP pipes.This document specifies the req

32、uirements for non-circular GRP pipe systems, designed to be used for the renovation of existing channels or open cut installation.This document specifies dimensions, requirements and tests of non-circular pipes including short and long-term properties. To establish long-term properties, it is recomm

33、ended to use the circular pipes samples.Annex A shows commonly used calculation methods but only as information. The calculation method is selected by the designer.This document does not include the recommended practice for installation as this should be a separate document.vi ISO 2017 All rights re

34、served Plastics piping systems for drainage and sewerage without pressure Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) Dimensions, requirements and tests1 ScopeThis document specifies the required properties of the pip

35、ing system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage without pressure including culverts.It is the responsibility of the purchaser or specifier to make the appropriate selections t

36、aking into account their particular requirements and any relevant national regulations and installation practices or codes.This document is applicable to non-circular GRP-UP pipes, with flexible or rigid joints, primarily intended for use in buried installations but may also be used to reline existi

37、ng non-circular pipe lines.NOTE 1 GRP-UP includes pipes with vinyl ester liners or made entirely from vinyl ester.NOTE 2 Piping systems conforming to this document can be used also for non-buried applications provided the influence of the environment, e.g. from UV-radiation, and the supports are con

38、sidered in the design of the pipes, fittings and joints.This document is applicable to pipes, fittings and their joints of nominal sizes from DN 150 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 C.2 Normative referencesThe following

39、documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 75-2:201

40、3, Plastics Determination of temperature of deflection under load Part 2: Plastics and eboniteISO 178, Plastics Determination of flexural propertiesISO 3126, Plastics piping systems Plastics components Determination of dimensionsISO 4633, Rubber seals Joint rings for water supply, drainage and sewer

41、age pipelines Specification for materialsISO 8513:2016, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the initial longitudinal tensile strengthISO 8533, Plastics piping systems for pressure and non-pressure drainage and sewerage Gla

42、ss-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped jointsISO 8639, Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods for leaktightness and proof of structural design of flexi

43、ble jointsINTERNATIONAL STANDARD ISO 16611:2017(E) ISO 2017 All rights reserved 1BS ISO 16611:2017ISO 16611:2017(E)ISO 10468, Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factorI

44、SO 10928, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Methods for regression analysis and their useISO 10952, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for t

45、he inside of a section in a deflected conditionEN 681-1, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubberEN/TS 14632, Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure Glass-reinfor

46、ced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) Guidance for the assessment of conformity3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the foll

47、owing addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp3.1nominal sizeBN HNalphanumerical designation of size, which is common to all components in a piping system, it is a convenient pair of numbers

48、for reference purposes that is related to the maximum internal breadth (B) and the maximum internal height (H)Note 1 to entry: The designation for reference or marking purposes consists of the letters BN(B) HN(H) and the numerical values for (B) and (H), when expressed in millimetres.3.2declared dim

49、ensionsdimensions which a manufacturer states to be the internal breadth (B) and height (H) produced in respect of a particular nominal size BN HN3.3specific ring stiffnessSphysical characteristic of a circular pipe which is a measure of the resistance to ring deflection per metre length under external loadNote 1 to entry: Specific ring stiffness is determined using formula below and is expressed in Newtons per square metre (N/m2):SEId=m3whereE is the