BS ISO 16620-5-2017 Plastics Biobased content Declaration of biobased carbon content biobased synthetic polymer content and biobased mass content《塑料 生物基含量 生物基碳含量 生物基聚合物含量和生物基质量含量的声.pdf

1、BS ISO 16620-5:2017Plastics Biobased contentPart 5: Declaration of biobased carboncontent, biobased synthetic polymercontent and biobased mass contentBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 16620-5:2017 BRITISH STANDARDNational forewordThis British Sta

2、ndard is the UK implementation of ISO 16620-5:2017. The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include

3、all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 89829 7 ICS 83.080.01 Compliance with a British Standard cannot confer immunity from legal obligations.This Brit

4、ish Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 16620-5:2017 ISO 2017Plastics Biobased content Part 5: Declaration of biobased carbon content, biobased s

5、ynthetic polymer content and biobased mass contentPlastiques Teneur biosource Partie 5: Dclaration de la teneur en carbone biosourc, de la teneur en polymre synthtique biosourc et de la teneur en masse biosourceINTERNATIONAL STANDARDISO16620-5First edition2017-01Reference numberISO 16620-5:2017(E)BS

6、 ISO 16620-5:2017ISO 16620-5:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical

7、 including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, Switzerla

8、ndTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 16620-5:2017ISO 16620-5:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols and abbreviated terms . 24.1 Symbols . 24.2 Abbreviated terms . 25 General principles . 26 Decl

9、arations of the biobased content . 36.1 Principle 36.2 Declaration of the biobased carbon content . 36.3 Declaration of the biobased synthetic polymer content . 36.4 Declaration of the biobased mass content 4Annex A (informative) Examples of labelling systems . 5Bibliography 7 ISO 2017 All rights re

10、served iiiContents PageBS ISO 16620-5:2017ISO 16620-5:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical commit

11、tees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the In

12、ternational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the d

13、ifferent types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see http:/www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

14、 ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this do

15、cument is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in th

16、e Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 5, Physical-chemical properties.A list of all parts in the ISO 16620 series can be found on the ISO website.iv ISO 2017 All

17、rights reservedBS ISO 16620-5:2017ISO 16620-5:2017(E)IntroductionIncreased use of biomass resources for manufacturing plastic products is effective for reducing global warming and the depletion of fossil resources.Current plastic products are composed of biobased synthetic polymers, fossil-based syn

18、thetic polymers, natural polymers and additives that can include biobased materials.“Biobased plastics” refers to plastics that contain materials wholly or partly of biogenic origin.In the ISO 16620 series, the “biobased content” of biobased plastics refers to the amount of the biobased carbon conte

19、nt, the amount of the biobased synthetic polymer content or the amount of the biobased mass content only. ISO 2017 All rights reserved vBS ISO 16620-5:2017BS ISO 16620-5:2017Plastics Biobased content Part 5: Declaration of biobased carbon content, biobased synthetic polymer content and biobased mass

20、 content1 ScopeThis document specifies the requirements for the declarations and labels of the biobased carbon content, the biobased synthetic polymer content and the biobased mass content in plastic products.This document is applicable to plastic products and plastic materials, polymer resins, mono

21、mers or additives, which are made from biobased or fossil-based constituents.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For

22、undated references, the latest edition of the referenced document (including any amendments) applies.ISO 14020, Environmental labels and declarations General principlesISO 14021, Environmental labels and declarations Self-declared environmental claims (Type II environmental labelling)ISO 16620-2, Pl

23、astics Biobased content Part 2: Determination of biobased carbon contentISO 16620-3, Plastics Biobased content Part 3: Determination of biobased synthetic polymer contentISO 16620-4, Plastics Biobased content Part 4: Determination of the biobased mass content3 Terms and definitionsFor the purposes o

24、f this document, the terms and definitions given in ISO 16620-1 and ISO 16620-4 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.i

25、so.org/obpINTERNATIONAL STANDARD ISO 16620-5:2017(E) ISO 2017 All rights reserved 1BS ISO 16620-5:2017ISO 16620-5:2017(E)4 Symbols and abbreviated terms4.1 SymbolsxBTCpercent biobased carbon content to total carbonxBTOCpercent biobased carbon content to total organic carbonmBSPbiobased synthetic pol

26、ymer contentmBbiobased mass content4.2 Abbreviated termsTC total carbonTOC total organic carbon5 General principlesThe general principles for the development and use of environmental labels and declarations established in ISO 14020 shall be followed with modest modifications for biobased plastics as

27、 follows:a) Principle 1: labels and declarations shall be accurate, verifiable, relevant and not misleading.b) Principle 2: procedures and requirements for labels and declarations shall not be prepared, adopted, or applied with a view to, or with the effect of, creating unnecessary obstacles to inte

28、rnational trade.c) Principle 3: labels and declarations shall be based on scientific methodology that is sufficiently thorough and comprehensive to support the claim and that produces results that are accurate and reproducible.d) Principle 4: information concerning the procedure, methodology, and an

29、y criteria used to support labels and declarations shall be available and provided upon request to all interested parties.e) Principle 5: the development of labels and declarations shall take into consideration all relevant aspects of the claim they are intended for.f) Principle 6: labels and declar

30、ations shall not inhibit innovation which maintains or has the potential to improve environmental performance and sustainability.g) Principle 7: any administrative requirements or information demands related to labels and declarations shall be limited to those necessary to establish conformance with

31、 applicable criteria and standards of the labels and declarations.h) Principle 8: the process of developing labels and declarations should include an open, participatory consultation with interested parties. Reasonable efforts should be made to achieve a consensus throughout the process.i) Principle

32、 9: information on the aspects of products and services relevant to a label or declaration shall be available to purchasers and potential purchasers from the party making the label or declaration.The requirements for self-declared environmental claims, including statements, symbols and graphics, reg

33、arding products, specified in ISO 14021 shall be satisfied.Examples of labelling systems are given in Annex A.2 ISO 2017 All rights reservedBS ISO 16620-5:2017ISO 16620-5:2017(E)6 Declarations of the biobased content6.1 PrincipleThe declaration of the biobased content according to this document is a

34、pplicable to plastic products and plastic materials, polymer resins, monomers or additives which are made from biobased and/or fossil-based constituents.The biobased carbon content, the biobased synthetic polymer content or the biobased mass content determined by applying ISO 16620-2, ISO 16620-3 or

35、 ISO 16620-4, respectively, shall be declared only by using the format described in 6.2, 6.3, or 6.4, respectively.The responsible party for placing biobased plastic products on the market should verify if the presence of the label could be erroneously considered as a proof of suitability to organic

36、 recovery (i.e. composting and anaerobic digestion according to ISO 18606 or equivalent specifications) by the consumers and, therefore, bring to unaware wrong waste separation behaviour. If there is a risk of misinterpretation, for example, for disposable single-use products placed on those markets

37、 where organic waste collection has been already implemented, then the responsible party should adopt further forms of communication to the consumers to make them aware of the recovery characteristics of the biobased product and, therefore, reduce the risks of waste misplacement caused by misinterpr

38、etation of the label and term “biobased”.6.2 Declaration of the biobased carbon contentThe declaration of the biobased carbon content, expressed as a percentage of the total organic carbon, xBTOC, shall consist of a statement, where xBTOCis the value determined according to ISO 16620-2, rounded to t

39、he nearest integer.The declaration of the biobased carbon content, expressed as a percentage of the total carbon, xBTC, shall consist of a statement, where xBTCis the value determined according to ISO 16620-2, rounded to the nearest integer.Information shall be provided as follows:a) product identif

40、ication;b) biobased carbon content according to ISO 16620-2;1) expressed as a percentage of TOC: X %and2) expressed as a percentage of TC: X %c) “this declaration is in agreement with ISO 16620-5”.6.3 Declaration of the biobased synthetic polymer contentThe declaration of the biobased synthetic poly

41、mer content, expressed as a percentage of mass, mBSP, shall consist of a statement, where mBSPis the value determined according to ISO 16620-3, rounded to the nearest integer.Information shall be provided as follows:a) product identification;b) biobased synthetic polymer content according to ISO 166

42、20-3, expressed as a percentage of the total mass: X %; ISO 2017 All rights reserved 3BS ISO 16620-5:2017ISO 16620-5:2017(E)c) “this declaration is in agreement with ISO 16620-5”.6.4 Declaration of the biobased mass contentThe declaration of the biobased mass content, expressed as a percentage of th

43、e total mass, mB, shall consist of a statement, where mBis the value determined according to ISO 16620-4.Information shall be provided as follows:a) product identification;b) biobased mass content according to ISO 16620-4, expressed as a percentage of the total mass: X %;c) “this declaration is in a

44、greement with ISO 16620-5”.4 ISO 2017 All rights reservedBS ISO 16620-5:2017ISO 16620-5:2017(E)Annex A (informative) Examples of labelling systemsA.1 GeneralExamples of labelling systems are listed in Table A.1.Table A.1 Examples of labelling systemsName of the certification systemOrganization Type

45、of declaration Reference websiteBioPreferredUnited States Department of Agriculture (USDA)Biobased carbon contentwww.biopreferred.gov/BiomassPlaJapan BioPlastics Associ-ation (JBPA)Biobased synthetic polymer Indi-catorAssociation Chimie du Vgtal (ACDV)Biobased mass content Bi-obased ProductsDIN CE

46、RTCO Gesellschaft fr Konformittsbewer-tung mbHBiobased carbon content Biobased synthetic polymer contentwww.dincertco.de/en/dincertco/home.jspOK Biobased AIB-Vinotte Interna-tional s.a./n.v.Biobased carbon contentwww.okcompost.be/en/recognising-ok-environment-log-os/ok-biobased/A.2 USDAs BioPreferre

47、d programUSDAs BioPreferred program was created by the 2002 Farm Bill to increase the purchase and use of biobased products within the Federal Government. Congress reauthorized and strengthened the program in the 2008 Farm Bill to further promote the sale of biobased products. With the launch of thi

48、s new biobased product label, USDAs BioPreferred program is now comprised of two parts: a biobased product procurement preference program for federal agencies and a voluntary labelling initiative for the broad-scale marketing of biobased products.A.3 JBPAs BiomassPla Identification and Labelling sys

49、temJBPAs BiomassPla Identification and Labelling system was started from July 2006. The system is based on the following:a) The Positive List System for all biobased synthetic polymers and its compounds, films, etc.b) The minimum value of the biobased synthetic polymer content is 25 % (by weight) of products measured by 14C measurement based on ISO 16620-2 and calculated based on ISO 16620-3.c) All com