BS ISO 16754-2011 Earth-moving machinery Determination of average ground contact pressure for crawler machines《运土机械 履带式机械用平均对地接触压力的测定》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16754:2008Earth-moving machinery Determination of average ground contact pressure for crawler machinesBS ISO 16754:2008 BRITISH STANDARDNational forewordThis British Stand

2、ard is the UK implementation of ISO 16754:2008. The UK participation in its preparation was entrusted to TechnicalCommittee B/513/1, Earth moving machinery (International). A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not pur

3、port to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 54519 1 ICS 53.100 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the St

4、andards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 16754:2008Reference numberISO 16754:2008(E)ISO 2008INTERNATIONAL STANDARD ISO16754First edition2008-06-15Earth-moving machinery Determination of average ground contact pressur

5、e for crawler machines Engins de terrassement Dtermination de la pression moyenne de contact au sol des engins chenilles BS ISO 16754:2008ISO 16754:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but

6、shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this ar

7、ea. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use

8、by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in an

9、y form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 74

10、9 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedBS ISO 16754:2008ISO 16754:2008(E) ISO 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO mem

11、ber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmen

12、tal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Direc

13、tives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodi

14、es casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16754 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery,

15、Subcommittee SC 1, Test methods relating to machine performance. BS ISO 16754:2008BS ISO 16754:2008INTERNATIONAL STANDARD ISO 16754:2008(E) ISO 2008 All rights reserved 1Earth-moving machinery Determination of average ground contact pressure for crawler machines 1 Scope This International Standard s

16、pecifies a uniform method for calculating the average ground contact pressure of self-propelled and towed crawler (track-laying) earth-moving machines, as defined in ISO 6165, on soft surfaces with empty equipment or attachment. The average ground contact pressure value is used only for comparing di

17、fferent machine models. Actual ground contact pressure values under operating conditions will vary depending on load, position of the centre of gravity, terrain, track shoe type and size, and surface conditions. NOTE 1 Alternative methods for determining ground contact pressure could apply to some s

18、pecific machine families. NOTE 2 The calculation makes allowance for some penetration into the supporting soil surface and the resulting increase in support area. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, o

19、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6165:2006, Earth-moving machinery Basic types Identification and terms and definitions ISO 6746-1:2003, Earth-moving machinery Definitions of dimensions and co

20、des Part 1: Base machine 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6746-1 and the following apply. 3.1 operating mass OM mass of the base machine, with equipment and empty attachment in the most usual configuration as specified by the manufactu

21、rer, and with the operator (75 kg), full fuel tank and all fluid systems (i.e. hydraulic oil, transmission oil, engine oil, engine coolant) at the levels specified by the manufacturer and, when applicable, with sprinkler water tank(s) half-full NOTE 1 The mass of an operator is not included for non-

22、riding machines. NOTE 2 Ballast mass included at delivery can be included if specified by the manufacturer. NOTE 3 The operating mass is expressed in kilograms. ISO 6016 BS ISO 16754:2008ISO 16754:2008(E) 2 ISO 2008 All rights reserved3.2 overall crawler length L6 distance on X coordinate between tw

23、o X planes passing through the farthest points on the ground-supported portion of the track undercarriage See Figure 1. NOTE 1 It is expressed in millimetres. NOTE 2 L6 can also be determined according to 4.3. Figure 1 Overall crawler length 3.3 crawler base L2 distance on X coordinate between two X

24、 planes passing through the front idler axis and the sprocket (or rear idler) axis ISO 6746-1 See Figure 2. NOTE It is expressed in millimetres. Figure 2 Crawler base BS ISO 16754:2008ISO 16754:2008(E) ISO 2008 All rights reserved 33.4 track shoe width W4 distance on Y coordinate between two Y plane

25、s passing through the extreme lateral points of the same track shoe ISO 6746-1 See Figure 3. NOTE It is expressed in millimetres. Figure 3 Track shoe width 4 Requirements 4.1 General The machine shall be the standard configuration as specified by the manufacturer. 4.2 Calculation of average ground c

26、ontact pressure, PgDetermine the average ground contact pressure, Pg, in kilopascals, using Equation (1): g42 6 21 000 9,8070,35( )mPnW L L L=+ (1) where m is the operating mass; n is the number of tracks; L2is the crawler base; L6is the overall crawler length; W4is the track shoe width. BS ISO 1675

27、4:2008ISO 16754:2008(E) 4 ISO 2008 All rights reservedNOTE 1 Equation (1) provides allowance for some track penetration into the supporting soil surface and the resulting increase in support area. NOTE 2 In the Equation (1), symbols with subscripts have been used to represent the dimensions in order

28、 to avoid confusion between codes (e.g. L6) and values. 4.3 Determination of L6 L6 can also be determined using Equation (2), which can be used for all types of crawler configurations, including that shown in Figure 4, provided that the angle, , is greater than or equal to 10. 622L Ld=+ (2) where d

29、is the distance on the Z coordinate between the ground reference plane and the Z plane (see ISO 6746-1) passing through the front and rear roller axis, as shown in Figure 4; L2is the crawler base; L6is the overall crawler length. NOTE In the equation, symbols with subscripts have been used to repres

30、ent the dimensions in order to avoid confusion between (e.g. L6) codes and values. Angle shall be W 10. Figure 4 Distance and angle used in determining L6 BS ISO 16754:2008ISO 16754:2008(E) ISO 2008 All rights reserved 5Bibliography 1 ISO 6016, Earth-moving machinery Methods of measuring the masses

31、of whole machines, their equipment and components 2 SAE J1309:2003, Travel Performance and Rating Procedure, Crawler Mounted Hydraulic Excavators, Material Handlers, Knuckle Boom Log Loaders, and Certain Forestry Equipment BS ISO 16754:2008ISO 16754:2008(E) ICS 53.100 Price based on 5 pages ISO 2008

32、 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated

33、by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the la

34、test amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which

35、 can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying st

36、andardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In r

37、esponse to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through

38、its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with sta

39、ndardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards

40、Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988

41、no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: