BS ISO 1728-2006 Road vehicles - Pneumatic braking connections between motor vehicles and towed vehicles - Interchangeability《道路车辆 电动车和拖车之间的气动制动连接器》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58motor vehicles and towed vehicles Interchangeability ICS 43.040.40Road vehicles Pneumatic braking c

2、onnections between BRITISH STANDARDBS ISO 1728:2006BS ISO 1728:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49248 6Amendments issued since publicationAmd. No. Date Commentscontract. Users are respon

3、sible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 1728:2006.The UK participation in its preparation was entrusted to Technical Committee A

4、UE/11, Braking systems.A list of organizations represented on AUE/11 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 1728:2006(E)INTERNATIONAL STANDARD ISO1728Third edition2006-09-01Road vehicles Pneumatic

5、 braking connections between motor vehicles and towed vehicles Interchangeability Vhicules routiers Liaisons de freinage pneumatique entre automobiles et vhicules tracts Interchangeabilit BS ISO 1728:2006ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federatio

6、n of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

7、 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wi

8、th the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appro

9、val by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1728 was prepared by Technical Committe

10、e ISO/TC 22, Road vehicles, Subcommittee SC 2, Braking systems and equipment. This third edition cancels and replaces the second edition (ISO 1728:1980), which has been technically revised. BS ISO 1728:2006blank1Road vehicles Pneumatic braking connections between motor vehicles and towed vehicles In

11、terchangeability 1 Scope This International Standard specifies the requirements which ensure interchangeability of the pneumatic braking connections between motor vehicles and towed vehicles. It concerns vehicle combinations equipped with pneumatic braking systems with two lines: one control line an

12、d one supply line. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 400

13、9, Commercial vehicles Location of electrical and pneumatic connections between towing vehicles and trailers 3 Interchangeability requirements 3.1 Coupling head type The “Palm type” coupling head shall be used. It shall be fitted with an inhibiting device to prevent incorrect coupling (see Figures 1

14、 and 2). The towing vehicle shall be equipped with an automatic device ensuring, without manual operation, the continuity of the pipelines when they are coupled, and their closure on uncoupling. This device shall not affect the interchangeability. The coupling head shall make provision for any type

15、of valve to be fitted to the towing vehicle, provided that the valve can be opened by the standard coupling head on the towed vehicle and that the ability to be coupled with all coupling heads corresponding to this International Standard is not compromized. 3.2 Coupling head dimensions The dimension

16、s of the coupling heads shall be as given in Tables 1 and 2, and shown in Figures 1 and 2. This International Standard specifies only the dimensional details necessary for the coupling. All other dimensions not shown, as well as details of design, are left to the discretion of the manufacturer. 3.3

17、Location of coupling heads and flexible pipe connections The locations of both electrical and pneumatic connections between towing and towed vehicles are specified in ISO 4009. The location of coupling heads and flexible pipe connections on the towing and towed vehicles shall comply with ISO 4009. B

18、S ISO 1728:20062 3.4 Colour coding for connections For the supply line: RED. For the control line: YELLOW. The colour shall be related to the coupling head or to a clearly visible point close to the head, for example, pipes or an identification tag. 3.5 Orientation of coupling heads The coupling axi

19、s of the fixed coupling heads shall be horizontal. The vertical sealing face shall be located as follows, according to whether it concerns a road train or an articulated road train: truck: towards the right when the vehicle is viewed from the rear; semi-trailer: towards the left when the vehicle is

20、viewed from the rear. 3.6 Length of flexible pipe connections The length of the flexible pipe connections between towing and towed vehicles is specified in ISO 4009. The length of flexible pipe connections on the towing and towed vehicles shall comply with ISO 4009. Table 1 Dimensions for coupling h

21、ead for supply line Connection A amm B mm With resilient sealing ring (for heads “tractor” and “trailer”) 2,7 0,5 19 2 With mobile part providing for the opening of the automatic valve (see 3.1) 3,5 + 1 21 max. 11 min. aThe opening of the automatic device shall be assured even when two coupling head

22、s with the most adverse tolerances for pushing down the mobile part are connected together. It shall be possible to push down the sealing face until the dimension A is at zero. BS ISO 1728:20063Dimensions in millimetres Key 1 sealing face 3 inhibiting device 2 coupling axis 4 stop Figure 1 Coupling

23、head for supply line BS ISO 1728:20064 Dimensions in millimetres BS ISO 1728:20065Key 1 minimum free space for the crossing of inhibiting device of the other head 2 sealing face 3 coupling axis 4 inhibiting device 5 stop Figure 2 Coupling head for control line Table 2 Dimensions for coupling head fo

24、r control line Connection A amm B mm With resilient sealing ring (for heads “tractor” and “trailer”) 2,7 0,5 19 2 With mobile part providing for the opening of the automatic valve (see 3.1) 3,5 + 1 21 max. 11 min. aThe opening of the automatic device shall be assured even when two coupling heads wit

25、h the most adverse tolerances for pushing down the mobile part are connected together. It shall be possible to push down the sealing face until the dimension A is at zero. BS ISO 1728:20066 Bibliography 1 ISO 1726, Road vehicles Mechanical coupling between tractors and semi-trailers Interchangeabili

26、ty BS ISO 1728:2006blankBS ISO BSI389 Chiswick High RoadLondonW4 4AL1728:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal C

27、harter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccur

28、acy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which e

29、nsures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also avai

30、lable from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on nat

31、ional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 89

32、96 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Ema

33、il: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK

34、, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prio

35、r written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.