BS ISO 17602-2014 Ships and marine technology Metal valves for use in flanged pipe Face-to-face and centre-to-face dimensions《船舶和海洋技术 法兰管用金属阀 面到面和中心到面的尺寸》.pdf

1、BSI Standards PublicationBS ISO 17602:2014Ships and marine technology Metal valves for use inflanged pipe Face-to-faceand centre-to-face dimensionsBS ISO 17602:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 17602:2014.The UK participation in its preparati

2、on was entrusted to TechnicalCommittee SME/32/-/3, Ships and marine technology - Piping andmachinery.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are resp

3、onsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 80665 0ICS 47.020.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards

4、 Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 17602:2014 ISO 2014Ships and marine technology Metal valves for use in flanged pipe Face-to-face and centre-to-face dimensionsNavires et technologie maritime Vannes en mtal pour tuyaux brides

5、 Dimensions face-face et face-axeINTERNATIONAL STANDARDISO17602First edition2014-04-15Reference numberISO 17602:2014(E)BS ISO 17602:2014ISO 17602:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication ma

6、y be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the

7、 requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 17602:2014ISO 17602:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative ref

8、erences 13 Terms and definitions . 14 Typical types of valves 25 Dimensions and tolerances . 4Bibliography .12BS ISO 17602:2014ISO 17602:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pre

9、paring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in

10、 liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC

11、 Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility t

12、hat some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent

13、declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as informat

14、ion about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee SC 3, Piping and machinery.iv ISO 2014 All rights rese

15、rvedBS ISO 17602:2014ISO 17602:2014(E)IntroductionThis International Standard establishes face-to-face and centre-to-face dimensions for metal marine valves to permit a degree of dimensional interchangeability in ships and marine piping.It is intended for use in selecting valves in piping for ships

16、and marine services.This International Standard specifies face-to-face and centre-to-face dimensions of valves for ships and marine services including supplementary series of special valves under Standards for ships, other than those specified in ISO 5752:1982 for variety of types and series of gene

17、ral industrial valves.The tables of face-to-face dimensions in this International Standard and those specified in ISO 5752:1982 represent a considerable rationalization of international practices for metallic valves to be used worldwide in the shipbuilding and marine services. The pressure/temperatu

18、re ratings for the different types of valves are those to be specified in the valve product standards for the types of valve and materials used. ISO 2014 All rights reserved vBS ISO 17602:2014BS ISO 17602:2014Ships and marine technology Metal valves for use in flanged pipe Face-to-face and centre-to

19、-face dimensions1 ScopeThis International Standard specifies the basic series of face-to-face or centre-to-face dimensions for two-way metal valves used in flanged pipe systems for ship and marine services. Each series of face-to-face or centre-to-face dimensions can be used as required with flanges

20、 of mating dimensions conforming to ISO 7005-1, ISO 7005-2, and ISO 7005-3 or other national standards.The range of pressure ratings, in “K” values, is 5 - 10 - 16 - 20 - 30 - 40 and those specified in ISO 5752.The range of nominal sizes, in “DN” or “A” values, is 15 - 20 - 25 - 32 - 40 - 50 - 65 -

21、80 - 100 - 125 - 150 - 200 - 250 - 300 - 350 - 400 - 450 - 500 - 550 - 600 - 650 - 700 - 750 - 800 - 900 - 1 000 - 1 200.NOTE For information, pressure ratings at room temperature (cold ratings up to 120 C) of K-series flanges are approximately as follows.Pressure class 5K 10K 16K 20K 30K 40KPressur

22、e rating (RT) 0,7 MPa 1,4 MPa 2,2 MPa 3,4 MPa 5,1 MPa 6,8 MPaPressure rating can differ by valve materials, sizes, and types. Reference shall be made to relevant product standards. For details of pressure temperature ratings of K-series flanges, refer to JIS Standards in the bibliography of this Int

23、ernational Standard. JIS F7300 specifies a comprehensive guide for selection of valves listed in Tables 1 to 5.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edi

24、tion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5752, Metal valves for use in flanged pipe systems Face-to-face and centre-to-face dimensionsISO 7005-1, Pipe flanges Part 1: Steel flanges for industrial and general serv

25、ice piping systemsISO 7005-2, Metallic flanges Part 2: Cast iron flangesISO 7005-3, Metallic flanges Part 3: Copper alloy and composite flangesISO 8277, Ships and marine technology Pipework and machinery Information transfer3 Terms and definitionsFor the purposes of this document, the following term

26、s and definitions apply.3.1nominal size (DN: A)alphanumeric designation of size for components of a pipework system, which is used for reference purposesNote 1 to entry: It comprises the letters DN or A followed by a dimensionless whole number which is indirectly related to the physical size, in mil

27、limetres, of the bore or outside diameter of the end connections.INTERNATIONAL STANDARD ISO 17602:2014(E) ISO 2014 All rights reserved 1BS ISO 17602:2014ISO 17602:2014(E)Note 2 to entry: Designation is to be indicated by the letters DN, followed by a number, or a number followed by the letter A.Note

28、 3 to entry: The number following the letters DN or A does not represent a measurable value and should not be used for calculation purposes except where specified in the relevant standard.3.2nominal pressureinternal pressure that a pipe is designed to safely withstandNote 1 to entry: Nominal pressur

29、es in this International Standard follow one of the following systems, the K rating system to ISO 8277 and the PN rating system or the class rating system to ISO 57523.3face-to-face dimension (for straight pattern valves)distance, in millimetres, between the two planes perpendicular to the valve axi

30、s located at the extremities of the body end ports or as can be specified in the relevant valve products standardsNote 1 to entry: The face-to-face dimension for butterfly valves is the distance between the extremities of the valve in the installed conditions. See Figure 3 a) as an example to know h

31、ow face-to-face dimension is measured.3.4centre-to-face dimension(for angle pattern valves)distance, in millimetres, between the plane located at the extremity of either body end port and perpendicular to its axis and the other body end port axisNote 1 to entry: See Figure 3 b) as an example to know

32、 how centre-to-face dimension is measured.Note 2 to entry: It should be taken into account that an angle pattern valve can have different centre-to-face dimensions for its inlet port and outlet port.4 Typical types of valvesTypical types of valves shall be as given in Figures 1 to 6.Figures 1 to 6 a

33、re intended to be a diagrammatic only and should not be used as symbols. They do not assume the principle or the construction details. Screw-down non-return (SDNR) valves shown in Figure 5 and inside screw, non-rising stem gate valves shown in Figure 6 are types of valves especially for marine use.F

34、igure 1 Wedge gate valves2 ISO 2014 All rights reservedBS ISO 17602:2014ISO 17602:2014(E)a) Wafer butterfly valve b) Double-flanged butterfly valveFigure 2 Butterfly valvesa) Globe valve b) Globe-type angle valveKeyaFace-to-face dimension.bCenter-to-face dimension (outlet).cCenter-to-face dimension

35、(inlet).Figure 3 Globe valvesa Lift-type check valve b) Swing-type check valve c) Lift-type angle check valveFigure 4 Non-return valves ISO 2014 All rights reserved 3BS ISO 17602:2014ISO 17602:2014(E)a) SDNR globe valve b) SDNR angle valveFigure 5 Screw-down non-return (SDNR) valvesFigure 6 Inside s

36、crew, non-rising stem gate valves5 Dimensions and tolerancesThe face-to-face or centre-to-face dimensions, as appropriate for the types of valves included in this International Standard, shall be in accordance with Tables 1 to 5, and the tolerances shall be in accordance with Tables 6 and 7, or dime

37、nsions and tolerances in accordance with ISO 5752.4 ISO 2014 All rights reservedBS ISO 17602:2014ISO 17602:2014(E)Table 1 Face-to-face dimensions for gate valvesDimensions in millimetresNominal size DN: AMaterialBronze Cast iron Cast steelNominal pressure5K Rising stem10K Rising stem5K Non-rising st

38、em10K Non- rising stem16K Non-rising stem10K Non-rising stemHull valve, non- rising stemDN15 15A 90 100 DN20 20A 100 110 DN25 25A 110 120 DN32 32A 130 140 DN40 40A 140 150 DN50 50A 180 200 200 200DN65 65A 190 220 220 220DN80 80A 200 230 230 230DN100 100A 230 250 250 250DN125 125A 250 270 270 270DN15

39、0 150A 270 290 290 290DN200 200A 290 320 310 310DN250 250A 330 380 340 340DN300 300A 370 440 490 380 380DN350 350A 410 500 540 420 420DN400 400A 470 590 610 480 480DN450 450A 500 640 450DN500 500A 550 710 500550A 600 780 550DN600 600A 660 850 600650A 650DN700 700A 700750A 750DN800 800A 800NOTE 1 Nom

40、inal size shall be designated by the letters DN, followed by a number, or a number followed by the letter A.NOTE 2 Refer to the note in Clause 1 of this International Standard for K-series ratings: 5K, 10K, and 16K. ISO 2014 All rights reserved 5BS ISO 17602:2014ISO 17602:2014(E)Table2 Face-to-face

41、dimensions for straight pattern globe valve, lift-type check valve, and SDNR globe valveDimensions in millimetresNominalsizeDN:AMaterialBronzeCastironSteelNominal pressure and type5K16KHullvalve5K10K16K5K10K20K30K40KAir valveHullvalveDN1515A100110110140150150DN2020A110120120160170170DN2525A120130130

42、180200200DN3232A140160160190229220DN4040A160180180200241240DN5050A210210220220220230292260220DN6565A250250270270270270330310270DN8080A280300300300300356340300DN100100A340350350350350410432390350DN125125A410420430420430460508470420DN150150A480490500490500500559540490DN200200A570570570570560570DN25025

43、0A740740740740660740DN300300A840840840840840DN350350A940DN400400A1050NOTE1Nominal size shall be designated by the letters DN, followed by a number, or a number followed by the letter A.NOTE2Refer to the note in Clause1of this International Standard for K-series ratings: 5K, 10K, 16K, 20K, 30K, and 4

44、0K.6 ISO 2014 All rights reservedBS ISO 17602:2014ISO 17602:2014(E)Table3 Centre-to-face dimensions for angle pattern globe valves, lift-type angle check valves, and SDNR angle valveDimensions in millimetresNominalsizeDN:AMaterialBronzeCastironSteelNominal pressure and type5K16KHullvalve5K10K16K5K(i

45、nlet/outlet)10K20K30K40KAirvalveHullvalve(inlet/outlet)DN1515A557070759090DN2020A607575809595DN2525A65858595100100DN3232A809595100114114DN4040A85100100110121121DN5050A100100120120120125146146120DN6565A115115130130130135165165130DN8080A130140150140150178178140DN100100A150160170160170205216205160DN125

46、125A170180200180200230254230180DN150150A190205225205225250279250205DN200200A220230250230280300230DN250250A275290320/275290310290DN300300A310320370/310320320DN350350A360360360/320DN400400A395420400/350DN450450A440450/380DN500500A485500/430550A530550/460DN600600A610/500NOTE1Nominal size shall be desig

47、nated by the letters DN, followed by a number, or a number followed by the letter A.NOTE2Refer to the note in Clause1of this International Standard for K-series ratings: 5K, 10K, 16K, 20K, 30K, and 40K. ISO 2014 All rights reserved 7BS ISO 17602:2014ISO 17602:2014(E)NominalsizeDN:AMaterialBronzeCast

48、ironSteelNominal pressure and type5K16KHullvalve5K10K16K5K(inlet/outlet)10K20K30K40KAirvalveHullvalve(inlet/outlet)650A660/540DN700700A710/570750A760/610DN800800A810/650NOTE1Nominal size shall be designated by the letters DN, followed by a number, or a number followed by the letter A.NOTE2Refer to the note in Clause1o