BS ISO 17683-2014 Ships and marine technology Ceramic weld backing for marine use《船舶与海洋技术 海上用陶瓷焊接衬垫》.pdf

1、BSI Standards PublicationBS ISO 17683:2014Ships and marine technology Ceramic weld backing formarine useBS ISO 17683:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 17683:2014.The UK participation in its preparation was entrusted to TechnicalCommittee SME/

2、32/-/8, Ships b) type II ceramic weld backing with metal cases. ISO 2014 All rights reserved 1BS ISO 17683:2014ISO 17683:2014(E)5 Dimensions and appearance5.1 GeneralFor inspection of its dimensions and appearance, six strips of ceramic weld backing shall be randomly selected. Each one of the sample

3、s shall meet the requirements in 5.2 and 5.3.5.2 Dimensions5.2.1 The tolerance of thickness for ceramic weld backing block shall be 0,5 mm of its thickness.5.2.2 The length tolerance for a strip of ceramic weld backing shall be 10 mm to +20 mm of its length.5.2.3 The centreline tolerance for ceramic

4、 weld backing block with moulding groove shall be 1,0 mm.5.2.4 The angle tolerances of a triangular or trapezoidal ceramic weld backing block shall be 2.5.3 Appearance5.3.1 Defects, such as damage and rounded corners, are not allowed for the joints between ceramic weld backing blocks other than roun

5、ded corners made by the mould itself.5.3.2 Within the area of the groove of the ceramic weld backing blocks and 2 mm on either side of them, mould sticking grain shall not be larger than 0,5 mm and the defect of the pit and damages shall not be more than 0,5 mm on the surface of the ceramic weld bac

6、king blocks.6 Performance and test6.1 Moisture absorption rate6.1.1 The moisture absorption rate shall be measured as follows.a) Randomly select three samples among the ceramic weld backing blocks. The dust on their surface shall be blown clear. Lay the samples on a tray, then put into an oven of co

7、nstant temperature and humidity together.b) Switch on the power of the oven and adjust the humidity to (95 3) % and the temperature to (25 2) C.c) Keep the samples and tray in the oven for 4 h, then take the samples out of the oven, weigh all samples, and record the weights as m2separately with an a

8、ccuracy of 0,001 g.d) Lay the samples on the tray, then place into the oven of constant temperature. Switch on the power of the oven, adjust the temperature to 200 C, and keep for 2 h.e) Take the samples out of the oven and keep it in the dryer until it cools down to the room temperature. Weigh all

9、samples by an analytical balance, and record the weights as m1separately with an accuracy of 0,001 g.f) The moisture absorption rate for each sample shall be calculated in accordance with Formula (1).2 ISO 2014 All rights reservedBS ISO 17683:2014ISO 17683:2014(E)Wmmma=211100% (1)whereWais the value

10、 of the moisture absorption rate (%);m1is the weight of dried sample (g);m2is the weight of sample which has absorbed water vapour sufficiently (g).g) Calculate the average value of the three samples.6.1.2 The average value of the moisture absorption rate shall be less than 0,35 %.6.2 Refractoriness

11、6.2.1 The refractoriness should be determined according to the welding method and melting point for the metal to be welded.6.2.2 Randomly select one ceramic weld backing block. The test of the refractoriness shall be conducted according to ISO 528.6.3 Chemical composition6.3.1 The content of sulfur

12、and phosphorus in the ceramic weld backing shall be analysed by an appropriate method and shall be less than 0,1 %.6.3.2 The content of boron in the ceramic weld backing shall be analysed by an appropriate method and shall be less than 0,01 %.6.3.3 Any analytical technique can be used, but in case o

13、f dispute, reference shall be made to established, published methods.6.4 Adhesive aluminium foil tape6.4.1 Randomly select one strip of type I ceramic weld backing for the adhesive aluminium foil tape test.6.4.2 The peeling strength of adhesive aluminium foil tape shall be determined in accordance w

14、ith ISO 29862 and shall be more than 12 N/25 mm.6.5 Metal cases6.5.1 Randomly select one strip of type II ceramic weld backing for the metal cases test.6.5.2 Erect the strip of ceramic weld backing, and there is no loose between the ceramic weld backing and metal cases. ISO 2014 All rights reserved

15、3BS ISO 17683:2014ISO 17683:2014(E)7 Type approval test7.1 GeneralThe type approval test shall be carried out under one of the following situations:a) initial production;b) upon reproduction or re-manufacturing, after being suspended from production for half a year or more, or production for 4 y con

16、tinuously;c) whenever the manufacturing technique which could affect the performance or quality of the products, or its ingredient and raw material, is changed significantly.7.2 Test itemsThe following tests for type approval shall be carried out, in addition to the items required in 5.2 and 5.3:a)

17、moisture absorption rate (see 6.1);b) refractoriness (see 6.2);c) chemical composition (see 6.3);d) adhesive aluminium foil tape (for type I) (see 6.4);e) metal cases (for type II) (see 6.5).7.3 Acceptance criteriaIf the samples meet all test requirements, the batch of ceramic weld backing will be d

18、eemed to have passed the type test. However, if the samples fail to meet any of the test requirements, additional double of samples shall be tested. If the additional samples pass all test requirements, the batch of ceramic weld backing will be deemed to have passed the type test. Otherwise, the bat

19、ch of ceramic weld backing will be deemed to have failed the type test.8 Acceptance test8.1 Test itemsPrior to delivery of the batch of ceramic weld backing blocks, the manufacturer shall test every batch of ceramic weld backing block for the following items:a) dimensions and tolerances (see 5.2);b)

20、 appearance (see 5.3);c) moisture absorption rate (see 6.1);d) chemical composition (see 6.3).8.2 Acceptance criteriaWith the same lot of raw materials, ingredients, and manufacturing technique, the ceramic weld backing can be inspected as one batch which should not be more than 500 000 m. If less t

21、han 500 000 m, the products should be treated as a batch.4 ISO 2014 All rights reservedBS ISO 17683:2014ISO 17683:2014(E)If the batch of ceramic weld backing meets the requirements specified in 8.1, the batch of the products will be deemed to have passed the acceptance test. However, if some samples

22、 fail to meet any of the test requirements, additional double of samples can be allowed only one time for re-test. If the additional samples pass the test requirements in 8.1, the batch of the products will be deemed to have passed the acceptance test. Otherwise, the batch of the products will be de

23、emed to have failed the acceptance test.9 Marking, packaging, and storage9.1 Marking9.1.1 The type of an accepted ceramic weld backing is to be marked after the number of this International Standard (i.e. ISO 17683). For example, a ceramic weld backing of type I is to be marked as follows:Ceramic we

24、ld backing ISO 17683-I9.1.2 Markings on the package shall have the following information:a) the number of this International Standard (i.e. ISO 17683:2014);b) the name of the manufacturer or supplier;c) the trade name, lot number, and number of pieces;d) health and safety warnings as required;e) the

25、 country of origin.9.2 PackagingCeramic weld backing shall be suitably packaged to ensure against damage during shipment and storage under normal conditions.9.3 StorageThe ceramic weld backing should be maintained in a dry, ventilated room. ISO 2014 All rights reserved 5BS ISO 17683:2014ISO 17683:20

26、14(E) ISO 2014 All rights reservedICS 47.020.10Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and ot

27、her standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expert

28、ise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standa

29、rdsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including Britis

30、h and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of su

31、bscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7

32、 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to B

33、SI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards pub

34、lications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revi

35、sion. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standa

36、rds and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted

37、 under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright &

38、 Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW