BS ISO 17941-2015 Ships and marine technology Hydraulic hinged watertight fireproof doors《船舶与海洋技术 液压铰链水密防火门》.pdf

1、BSI Standards PublicationBS ISO 17941:2015Ships and marine technology Hydraulic hinged watertightfireproof doorsBS ISO 17941:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 17941:2015. The UK participation in its preparation was entrusted to TechnicalCommi

2、ttee SME/32/-/8, Ships 47.020.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e

3、 c t e d ISO 2015Ships and marine technology Hydraulic hinged watertight fireproof doorsNavires et technologie maritime Portes tanches incombustibles charnires hydrauliquesINTERNATIONAL STANDARDISO 17941First edition 2015-03-01Reference number ISO 17941:2015(E)BS ISO 17941:2015ISO 17941:2015(E)ii IS

4、O 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet

5、, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in

6、SwitzerlandBS ISO 17941:2015ISO 17941:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Classification and designation . 13.1 Types 13.2 Structure and main dimensions . 23.3 Manual hydraulic and electric-hydraulic system schematic diagram . 43.4 Electrical system diagram . 53.5 De

7、signation 54 Requirement and inspection . 54.1 Material . 54.2 Appearance 54.3 Welds . 64.4 Heat Treatment . 64.5 Anti-corrosion 64.6 Tightness 64.6.1 Degrees of contact 64.6.2 Water pressure 64.7 System. 64.8 Control 64.9 Flexibility . 74.10 Alarm . 74.11 Status indication 74.12 Inclination test 74

8、.13 Fire resistance . 85 Marking, packaging, transport, and storage 95.1 Marking . 95.2 Packaging . 95.3 Transportation and storage . 9Annex A (informative) Watertight doors hydraulic system schematic diagram .10Annex B (informative) Watertight doors electrical system schematic diagram .11 ISO 2015

9、All rights reserved iiiContents PageBS ISO 17941:2015ISO 17941:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technic

10、al committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wi

11、th the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed

12、for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

13、ts. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this

14、 document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to

15、Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee SC 8, Ship design.iv ISO 2015 All rights reservedBS ISO 17941:2015ISO 17941:2015(E)IntroductionFire-proof doors shall comply with

16、 the requirements of IMO FTP-code. The standard provides reference for design, manufacturing and inspection of hydraulic watertight hinged fireproof doors, so it is not imperative for shipyards to implement the standard. ISO 2015 All rights reserved vBS ISO 17941:2015BS ISO 17941:2015Ships and marin

17、e technology Hydraulic hinged watertight fireproof doors1 ScopeThis International Standard specifies classification and designation, requirements, test method, marking, packaging, transport, and storage of hydraulic watertight hinged fireproof doors (hereinafter referred to as “watertight doors”).Th

18、is International Standard is applicable to the design, manufacture, and acceptance of hydraulic watertight hinged fireproof doors with water pressure not more than 1,0 MPa used for ships, other floating structures and ocean engineering.2 Normative referencesThe following documents, in whole or in pa

19、rt, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3796, Ships and marine technology Clear openin

20、gs for external single-leaf doorsISO 8501-1, Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous co

21、atingsIEC 61162-1:2010, Maritime navigation and radio communication equipment and systems Digital interfaces Part 1: Single talker and multiple listenersAWS D1.1/D1M:2008, Structural Welding Code SteelIMO Resolution MSC.302 (87), Adoption of performance standards for Bridge Alert Management3 Classif

22、ication and designation3.1 Types3.1.1 Depending on the opening direction, watertight doors shall be classified into two types (see Figure 1): Type R-Right-hand watertight door (the hinge stays right when the door opens towards the observer); Type L-Left-hand watertight door (the hinge stays left whe

23、n the door opens towards the observer).INTERNATIONAL STANDARD ISO 17941:2015(E) ISO 2015 All rights reserved 1BS ISO 17941:2015ISO 17941:2015(E)11L R Key1 hingeL left-hand doorR right-hand doorFigure 1 Opening directions3.1.2 According to the fire-protection rating, watertight doors shall be classif

24、ied into four levels: A-60, A-30, A-15, and A-0.3.2 Structure and main dimensions3.2.1 The structure and main dimensions of watertight doors shall be in accordance with Table 1 and Figure 2. The nominal size, L B, of watertight doors is denoted by reference to the clear opening according to ISO 3796

25、. Watertight doors of other dimensions can be provided upon agreement between manufacturer and purchaser.Table 1 Main dimensions for watertight doorDimensions in millimetresNominal size Opening in the bulkhead plate Door framesL B L1B1L2B21 200 600 1 340 740 1 480 8801 400 600 1 540 740 1 680 8801 4

26、00 750 1 540 890 1 680 1 0301 400 900 1 540 1 040 1 680 1 1801 600 600 1 740 740 1 880 8801 600 750 1 740 890 1 880 1 0301 600 900 1 740 1 040 1 880 1 1801 800 750 1 940 890 2 080 1 0301 800 900 1 940 1 040 2 080 1 180The tolerance is as follows: Nominal size:20mm; Opening in the bulkhead panel and

27、door frames:+22mm.2 ISO 2015 All rights reservedBS ISO 17941:2015ISO 17941:2015(E)4112 11 10 9876532B1B2L2LL1BtXXKey1 hinge 7 dog2 door panel 8 insulation3 door frame 9 insulation plate4 door opening/closing cylinder 10 fire-resistant sealing strip II5 driving mechanism 11 sealing strip6 lock cylind

28、er 12 fire-resistant sealing strip IFigure 2 Left-hand watertight door (Right-hand watertight door in contrast)3.2.2 The door panels sealing mechanism shall ensure the door is watertight. ISO 2015 All rights reserved 3BS ISO 17941:2015ISO 17941:2015(E)B2L2Figure 3 Door panels sealing mechanism3.3 Ma

29、nual hydraulic and electric-hydraulic system schematic diagramThe watertight doors manual hydraulic and electric-hydraulic system schematic diagram is provided in Annex A. Hydraulic pumps, cylinders, accumulators, piping, valves, and other components shall comply with requirements of the Administrat

30、ion and/or Classification Society.4 ISO 2015 All rights reservedBS ISO 17941:2015ISO 17941:2015(E)3.4 Electrical system diagramThe watertight doors electrical system diagram is provided in Annex B. Electric wiring, motors, and electric components shall comply with requirements of the Administration

31、and/or Classification Society.3.5 DesignationThe watertight door conforming to this International Standard shall be designated as follows, in the order given:a) denomination: “Hydraulic hinged watertight fireproof door”;b) number of this International Standard: ISO 17941;c) fire resistance rating: A

32、60, A30, A15, A0;d) type: R or L;e) nominal size;f) working pressure.EXAMPLE The designation for a hydraulic hinged watertight fireproof door type R of nominal size 1 800 750, fire resistance rating A60, working pressure 0,5 MPa, is:Hydraulic hinged watertight fireproof door ISO 17941A60R1800 750 0,

33、54 Requirement and inspection4.1 Material4.1.1 Except as noted below, the main components of the watertight door (door panel, door frames, hinges, locking device) shall be manufactured from the materials given in Table 2. These materials shall have the minimum mechanical properties given in the tabl

34、e. Other materials can be used upon agreement between manufacturer and purchaser.Table 2 Minimum mechanical properties of materialsName of the componentsMinimum yield stressN/mm2Tensile strengthN/mm2door panel 355 490-620door frame 235 375-460hinge 235 375-460locking device 315 440-5904.1.2 Insulati

35、on and structural materials used in the structure shall be non-combustible meeting Part 1 of Annex 1 of the 2010 FTP Code as amended.4.1.3 Fire resistant sealing strips shall comply with the demand of working pressure and be non-combustible meeting Part 1 of Annex 1 of the 2010 FTP Code as amended.S

36、ealing strips and gaskets for watertight integrity shall comply with the demand of working pressure.4.2 AppearanceWatertight door surfaces shall be smooth, without defects and sharp edges, scoring, and indentation. ISO 2015 All rights reserved 5BS ISO 17941:2015ISO 17941:2015(E)4.3 WeldsAll welds of

37、 watertight doors (door frames and doors panels) shall be smooth, without pores, cracks, slag, undercut, and lack of fusion defects in accordance with AWS D1.1/D1M:2008.4.4 Heat TreatmentExcept as noted below, welded door frames and panels shall be heat treated after welding to relieve stress in ord

38、er to ensure their water tightness.The heat treatment is not necessary for the watertight door under 0,1 MP at relieve stress.4.5 Anti-corrosionThe preparation grade of watertight doors shall be at least ISO 8501-1, Sa2 1/2 and shall be St3 locally through manual polishing. The anti-corrosion paint

39、shall be applied twice and the grease shall be applied to the movable friction surface.4.6 Tightness4.6.1 Degrees of contactTo test the degree of contact between the sealing strip of the door panel and the door frame, apply a powder uniformly on the door frames. The powder shall be of a highly visib

40、le contrasting colour such as blue. Next, close the door securely and open the door again. Examine the sealing strip of the door panel which shall have the powder uniformly and continuously pressed on it, and the width of the powder shall not be smaller than one half of the contact width.4.6.2 Water

41、 pressureWatertight doors shall be tested by water hydrostatic pressure to the working pressure, there shall be no leakage. The test pressure for offshore structure shall be the working pressure plus 5 m of water head.4.7 SystemThe hydraulic system of the watertight doors shall be subject to 1,5 tim

42、es the working pressure without any leakage.4.8 Control4.8.1 The watertight door control system shall be provided with “Close all doors”, “Local”, and “Close individually” switches on the control panel.4.8.2 All opened watertight doors shall be automatically closed within 60 s when the selector swit

43、ch is set to “Close all doors”. Each open watertight door shall be closed within 20 s approximately 40 s of the start of closing for that door under power.4.8.3 Watertight doors shall be able to be opened and closed at both sides manually or electrically when the selector switch is on the position o

44、f “Local”.4.8.4 Watertight doors shall be able to be closed individually when the selector switch is on the position of “Close individually”.4.8.5 At the hydraulic pump cut-in pressure, the accumulator shall have enough energy to operate watertight doors within the control area for 3 times, i.e. Clo

45、se Open Close against an adverse inclination 15.6 ISO 2015 All rights reservedBS ISO 17941:2015ISO 17941:2015(E)4.8.6 In the event of loss of power, the watertight doors shall be able to be opened or closed by manually opening the ball valve of the hydraulic system and then operating the hand pump a

46、t either side of the door.4.8.7 Manual closing of the door via hand pump shall not exceed 90 s from fully open to fully closed position.4.8.8 For the electro-hydraulic control, the closing time of a single watertight door shall be within 20 s approximately 40 s and the rate of closing shall be rough

47、ly even.4.9 FlexibilityCheck the rotational flexibility of watertight doors using local manual hydraulic and electro-hydraulic operation control. There shall be no jam on the transmission components and friction surface.4.10 Alarm4.10.1 When remotely controlling the watertight door, the alarm on bot

48、h sides of the watertight doors shall provide continuous audible and visual alarm signals within 5 s to 10 s before the door starts to close and continue until it is completely closed.4.10.2 When using manual hydraulic control or electro-hydraulic control on both sides of the watertight doors to ope

49、rate the watertight doors, the alarm on both sides of the watertight door shall provide continuous audible and visual alarm signals until it is completely closed.4.10.3 A fault alarm lamp shall be provided on the remote control panel. The lamp shall send an alarm signal in case of low level of hydraulic reservoir, low pressure of the hydraulic system, loss of power, or motor overload.4.10.4 There shall be an interface to the VOYAGE DATA RECORDER (VDR) to transmit each door